• Journal of Biosystems Engineering
• /
• v.1 no.1
• /
• pp.17-48
• /
• 1976

In analyzing the operational characteristics of a rice whitening machine, the internal radial pressure of the machine was measured using strain gage equipment. Changes in cylinder and feed screw configurations, screen type, cylinder speed and counter-pressure levels were examined to determine their impact on the quality and quantity of milled rice and the performance of the machine. The results are summarized as follows: 1. The internal radial pressure in the whitening chamber varied with the surface condition of the grain being processed. During the first or second pass through the machine, pressure was relatively low, reached a maximum after two to three passes with combinations I and II, three to six with combination III and then began to fall. 2. The pitch of the feed screw and the size of the feed gate opening which determine the rate of entry of grain into the whitening chamber, appeared to be the most important factor aff-::cting the degree of radial pressure, quality and quantity of milled rice and the efficiency of the machine. Using a feed screw with a wide pitch (4.8cm), radial pressure was relatively high and head rice recovery ratio \vere quite low. In this case capacity and machine effic\ulcorneriency were much higher than obtained when using a feed screw with a narrow pitch (2.3cm). Very significant responses in radial pressure, head rice recovery rates and machine capacity were observed with changes in cylinder speed and counter-pressure levels when using the wide pitch feed screw. 3. The characteristics of the screen which surrounds the whitening chamber had an important effect on whitening efficiency. The existence of small protuberances on the original screen resulted in significant increases in both machine capacity and efficiency but without a significant decrease in head rice recovery or development of excessive radial pressure. Further work is required to determine the effects of screen surface conditions and the shape of the cylinderical steel roller on the rate of bran removal, machine efficiency and recovery rates. The size of the slotted perforations 0:1 the screen affects total milled rice recovery. The opening size on the original screen was fabricated to accommodate the round shape of Japonica rice varieties but was not suitable for the more slender Indica type. Milling Indica varieties with this screen resulted in a reduction in total milled rice recovery. 4. An increase in cylinder speed from 380 to 820 rpm produced a positive effect on head rice recovery for all machine combinations at every level of counter-pressure used in the tests. Head rice recovery was considerably lower at 380rpm using a wide screw pitch when compared to the results obtained at speeds from 600 to 820 r.p.m. The effects of cylinder speed On radial pressure, capacity and machine efficiency showed contrasting results, depending on the width of the feed screw pitch. With a narrow feed screw pitch (2.3cm), a direct proportional relationship was observed bet\ulcornerween cylinder speed and both radial pressure and machine efficiency. In contrast, using a 4.8 centimeter pitch feed roller produced a series of inverse relationships between the above variables. Based on the results of this study it is recommended when milling Indica type long grain rice varieties that the cylinder speed of the original machine be increased from 500-600 rmp up to a minimum of 800 rpm to obtain a greater abrasive effect between the grain and the screen. The pitch of the feed screw should be also reduced to decr\ulcornerease the level of internal radial pressure and to obtain higher machine efficiency and increased quality of milled rice with increased cylinder speeds. Further study on the interaction between cylinder speed and feed screw pitch is recommended. 5. An increase in the counter pressure level produced a negative effect On the head rice recovery with an increase in radial pressure, capacity, and machine efficiency over all combinations and at every level of cylinder speed. 6. Head rice recovery rates were conditioned primarily by the pressure inside the whitening chamber. According to the empirical cha racteristics curve developed in this study, the relationships of head rice recovery ($Y_h$) and machine capacity ($Y_c$/TEX>) to internal radial pressure ($X_p$) followed an inverse quadratic function and a linear function respectively: $$Y_h^\Delta=\frac{1}{{1.4383-0.2951X_p^\ast+0.1425X_p^{\ast\ast}}^2} , (R^2=0.98)$$ $$Y_c^\Delta=-305.83+374.37X_p^{\ast\ast}, (R^2=0.88)$$ The correlation between capacity and power consumption per unit of brown rice expressed in the following exponential function: $$Y_c^\Delta=1.63Y_c^{-0.7786^\{\ast\ast}, (R^2=0.94)$$ These relationships indicate that when radial pressure increases above a certain range (1. 6 to 2.0 kg/$cm^2$ based On the results of the experiment) head ricerecovery decrea\ulcornerses in a quadratic relation with a inear increase in capacity but without any decrease in power consump tion per unit of brown rice. On the other hand, if radial pressure is below the range shown above, power consumption increases dramatically with a lin\ulcornerear decrease in capacity but without significant increases in head rice recovery. During the operation of a given whitening machine, the optimum radial pressure range or the correct capacity range should be selected by controlling the feed rate and/or counter-pressure keeping in mind the condition of the grain, particulary the hardness. It was observed that the total number of passes is related to radial pessure level, feed rate and counter-pressure level. The higher theradial pressure the fewer num\ulcornerber of pass required but with decreased head rice recovery. In particular, when using high feed rates, the total number of passes should be increased to more than three by reducing the counter-pressure level to avoid decreaseases in head rice recovery (less than 65 percent head rice recovery on the basis of brown rice) at every cylinder speed. 7. A rapid rise in grain temperature seemed to have a close relationship with the pressure generated inside the whitening chamber and, subsequently with head rice reco\ulcornervery rates. The higher the rate of increase, the lower were the resulting head rice recoveries.

• Radiation Oncology Journal
• /
• v.18 no.4
• /
• pp.233-243
• /
• 2000

Purpose : First of all, this study was performed to assess the result of curative radiotherapy and to evaluate different possible prognostic factors for squamous cell carcinoma of the supraglottic larynx treated at the Pusan National University Hospital. The second goal of this study was by comparing our data with those of other study groups, to determine the better treatment policy of supraglottic cancer in future. Methods and Material : Thirty-two patients with squamous cell carcinoma of the supraglottic larynx were treated with radiotherapy at Pusan National University Hospital, from August 1985 to December 1996. Minimum follow-up period was 29 months, Twenty-seven patients (84.4$\%$) were followed up over 5 years. Radiotherapy was delivered with 6 MV photons to the primary laryngeal tumor and regional iymphatics with shrinking field technique. Ail patients received radiotherapy under conventional fractionated schedule (once a day). Median total tumor dose was 70.2 Gy (range, 55.8 to 75.6 Gy) on primary or gross tumor lesion. Thirteen patients had Induction chemotherapy with cisplatln and 5-fluorouracil (1-3 cycles). Patient distribution, according to the different stages, were as follows: stage I, 5/32 (15.6$\%$): stage II, 10/32 (31.3$\%$); stage III, 8/32 (25$\%$): stage IV, 9/32 (28.1$\%$). Results :The 5-year overall survival rate of the whole series (32 patients) was 51.7$\%$. The overall survival rate at 5-years was 80$\%$ in stage I, 66.7$\%$ in stage II, 42.9$\%$ in stage III, 25$\%$ in stage IV (p=0.0958). The S-year local control rates after radiotherapy were as fellows: stage I, 100$\%$; stage II, 60$\%$ stage III, 62.5$\%$; stage IV, 44.4$\%$ (p=0.233). Overall vocal preservation rates was 65.6$\%$, 100% In stage I, 70% in stage II, 62.5$\%$ In stage III, 44.4$\%$ in stage IV (p=0.210). There was no statistical significance in survival and local control rate between neoadjuvant chemotherapy followed by radiotherapy group and radiotherapy alone group. Severe laryngeal edema was found in 2 cases after radiotllerapy, emergent tracheostomy was done. Four patients were died from distant metastsis, . three in lung, one in brain. Double primary tumor was found in 2 cases, one in lung (metachronous), another in thyroid (synchronous). Ulcerative lesions were revealed as unfavorable prognostic factor ( p=0.0215), and radiation dose (more or less than 70.2 Gy) was an important factor on survival (p=0.002). Conclusion : The role of radiotherapy treatment of supraglottic carcinoma is to important factor on survival and to preserve the laryngeal function. Based on our data and other studies, early and moderately advanced supragiottic carcinomas could be successfully treated with either consewative surgery or radiotherapy alone. Both modalities showed similar results in survival and vocal preservation. For the advanced cases, radiotherapy alone is Inadequate for curative aim and surgery combined with radiotherapy should be done in operable patients. When patients refuse operation or want to preserve vocal function, or for the patients with inoperable medical conditions, combined chemoradiotherapy (concurrent) or altered fractionated radiotherapy with or without radiosensitizer should be taken into consideration in future.

• Journal of Chest Surgery
• /
• v.38 no.1 s.246
• /
• pp.44-49
• /
• 2005

Although thymomas are relatively common mediastinal tumors, to date not only has a universal system of pathologic classification not been established but neither has a clearly defined predictable relationship between treatment and prognosis been made. Recently, a new guideline for classification was reported by WHO, and efforts, based on this work, have been made to better define the relationship between treatment and pro­gnostic outcome. In the present study a comparative analysis between the WHO classification and Masaoka stage system with the clinical disease pattern was conducted. Material and Method: A total of 98 patients undergoing complete resection for mediastinal thymoma between Juanuary 1993 and June 2003 were included in the present study. The male female ratio was 48 : 50 and the mean age at operation was $49.6{\pm}13.9\;years.$ A retrospective analytic comparison studying the relationship between the WHO classification and the Masaoka stage system with the clinical disease pattern of thymoma was conducted. Pathologic slide specimens were carefully examined, details of postoperative treatment were documented, and a relationship with the prognostic outcome and recurrence was studied. Result: There were 7 patients in type A according to the WHO system of classification, 14 in AB, 28 in B 1, 23 in B2, 18 in B3, and 9 in type C. The study of the relationship between the Masaoka stage and WHO classification system showed 4 patients to be in WHO system type A, 7 in type AB, 22 in B 1, 17 in B2, and 3 in type B3 among 53 $(54{\%})$ patients shown to be in Masaoka stage I. Among 28 $(28.5{\%})$ patients in Masaoka stage II system, there were 2 patients in type A, 7 in AB, 4 in B 1, 2 in B2, 8 in B3, and 5 in type C. Among 15 $(15.3{\%})$ in Masaoka stage III, there were 1 patient in type B1, 3 in B2, 7 in B3, and 4 in type C. Finally, among 2 $(2{\%})$ patients found to be in Masaoka stage IV there was 1 patient in type B1, and 1 in type B2. The mean follow up duration was $28{\pm}6.8$ months. There were 3 deaths in the entire series of which 2 were in type B2 (Masaoka stages III and IV), and 1 was in type C (Masaoka stage II). Of the patients that experienced relapse, 6 patients remain alive of which 2 were in type B2 (Masaoka III), 2 in type B3 (Masaoka I and III) and 2 in type C (Masaoka stage II). The 5 year survival rate by the Kaplan-Meier method was $90{\%}$ for those in type B2 WHO classification system, $87.5{\%}$ for type C. The 5 year freedom from recurrence rate was $80.7{\%}$ for those in WHO type B2, $81.6{\%}$ for those in type B3, and $50{\%}$ for those in type C. By the Log-Rank method, a statistically significant correlation between survival and recurrence was found with the WHO system of classification (p<0.05). An analysis of the relationship between the WHO classification and Masaoka stage system using the Spearman correction method, showed a slope=0.401 (p=0.023), showing a close correlation. Conclusion: As type C of the WHO classification system is associated with a high postoperative mortality and recurrence rate, aggressive treatment postoperatively and meticulous follow up are warranted. The WHO classification and Masaoka stage system were found to have a close relationship with each other and either the WHO classification method or the Masaoka stage system may be used as a predict prognostic outcome of Thymoma.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.9 no.1
• /
• pp.1-18
• /
• 1973

For regulating the depth of midwater trawl nets towed at the optimum constant speed, the changes in the shape of warps caused by adding a weight on an arbitrary point of the warp of catenary shape is studied. The shape of a warp may be approximated by a catenary. The resultant inferences under this assumption were experimented. Accordingly feasibilities for the application of the result of this study to the midwater trawl nets were also discussed. A series of experiments for basic midwater trawl gear models in water tank and a couple of experiments of a commercial scale gears at sea which involve the properly designed depth control devices having a variable attitude horizontal wing were carried out. The results are summarized as follows: 1. According to the dimension analysis the depth y of a midwater trawl net is introduced by $$y=kLf(\frac{W_r}{R_r},\;\frac{W_o}{R_o},\;\frac{W_n}{R_n})$$) where k is a constant, L the warp length, f the function, and $W_r,\;W_o$ and $W_n$ the apparent weights of warp, otter board and the net, respectively, 2. When a boat is towing a body of apparent weight $W_n$ and its drag $D_n$ by means of a warp whose length L and apparent weight $W_r$ per unit length, the depth y of the body is given by the following equation, provided that the shape of a warp is a catenary and drag of the warp is neglected in comparison with the drag of the body: $$y=\frac{1}{W_r}\{\sqrt{{D_n^2}+{(W_n+W_rL)^2}}-\sqrt{{D_n^2+W_n}^2\}$$ 3. The changes ${\Delta}y$ of the depth of the midwater trawl net caused by changing the warp length or adding a weight ${\Delta}W_n$_n to the net, are given by the following equations: $${\Delta}y{\approx}\frac{W_n+W_{r}L}{\sqrt{D_n^2+(W_n+W_{r}L)^2}}{\Delta}L$$ $${\Delta}y{\approx}\frac{1}{W_r}\{\frac{W_n+W_rL}{\sqrt{D_n^2+(W_n+W_{r}L)^2}}-{\frac{W_n}{\sqrt{D_n^2+W_n^2}}\}{\Delta}W_n$$ 4. A change ${\Delta}y$ of the depth of the midwater trawl net by adding a weight $W_s$ to an arbitrary point of the warp takes an equation of the form $${\Delta}y=\frac{1}{W_r}\{(T_{ur}'-T_{ur})-T_u'-T_u)\}$$ Where $$T_{ur}^l=\sqrt{T_u^2+(W_s+W_{r}L)^2+2T_u(W_s+W_{r}L)sin{\theta}_u$$ $$T_{ur}=\sqrt{T_u^2+(W_{r}L)^2+2T_uW_{r}L\;sin{\theta}_u$$ $$T_{u}^l=\sqrt{T_u^2+W_s^2+2T_uW_{s}\;sin{\theta}_u$$ and $T_u$ represents the tension at the point on the warp, ${\theta}_u$ the angle between the direction of $T_u$ and horizontal axis, $T_u^2$ the tension at that point when a weights $W_s$ adds to the point where $T_u$ is acted on. 5. If otter boards were constructed lighter and adequate weights were added at their bottom to stabilize them, even they were the same shapes as those of bottom trawls, they were definitely applicable to the midwater trawl gears as the result of the experiments. 6. As the results of water tank tests the relationship between net height of H cm velocity of v m/sec, and that between hydrodynamic resistance of R kg and the velocity of a model net as shown in figure 6 are respectively given by $$H=8+\frac{10}{0.4+v}$$ $$R=3+9v^2$$ 7. It was found that the cross-wing type depth control devices were more stable in operation than that of the H-wing type as the results of the experiments at sea. 8. The hydrodynamic resistance of the net gear in midwater trawling is so large, and regarded as nearly the drag, that sweeping depth of the gear was very stable in spite of types of the depth control devices. 9. An area of the horizontal wing of the H-wing type depth control device was $1.2{\times}2.4m^2$. A midwater trawl net of 2 ton hydrodynamic resistance was connected to the devices and towed with the velocity of 2.3 kts. Under these conditions the depth change of about 20m of the trawl net was obtained by controlling an angle or attack of $30^{\circ}$.