• Tunnel and Underground Space
• /
• v.19 no.6
• /
• pp.534-544
• /
• 2009

The collapse of the underground cavity can cause the abrupt local subsidence of the ground surface. It can be hazardous to the stability of road and building for human activity. Therefore it is necessary to develop reinforcement methods for the filling of the underground cavity. This study was executed to improve the material quality and systems to fill the calcium-aluminate mineral $(C_{12}A_7)$ environmentally, and minimize the loss of filling materials for the steep underground cavity. Filling material which was developed in this study is composed of rapid hardening material and additives. The developed material had rapid hardening and non-separation ability in the water cavity condition, so it made the effective underground dam in the cavity with prevention of material loss when it was poured in the water cavity. Results of heavy metal leaching test for environmental assessment showed that it was environmentally suiTable material for the filling in the mine cavity.

• Tunnel and Underground Space
• /
• v.25 no.5
• /
• pp.470-486
• /
• 2015

Two-arch tunnels require minimal spacing between the 2 tunnels and thus occupy small amount of land compared to parallel tunnels. But it is rather expensive. The parallel tunnel is not as expensive, but it requires more land than 2-arch tunnels. This may cause a problem when there is a land shortage. The new design is to connect these two types of tunnels by another pair of parallel tunnels where the separation distance is gradually increasing. The applicability of this new design to the cases where rock condition is not even fair has to be verified since the width of the pillar between the connecting tunnels can be quite narrow. Therefore both two and three dimensional numerical analyses were conducted and pillar stability was examined for rock classes IV and V in two different ways. Results showed that this new design is still effective for poor rock conditions if central pillar is properly reinforced by tension bolts as long as overburden is less than five times of the tunnel diameter.

• Geomechanics and Engineering
• /
• v.11 no.2
• /
• pp.235-252
• /
• 2016

This paper presents a new numerical solution of the ultimate lateral capacity of rectangular piles in clay. The two-dimensional plane strain finite element was employed to determine the limit load of this problem. A rectangular pile is subjected to purely lateral loading along either its major or minor axes. Complete parametric studies were performed for two dimensionless variables including: (1) the aspect ratios of rectangular piles were studied in the full range from plates to square piles loaded along either their major or minor axes; and (2) the adhesion factors between the soil-pile interface were studied in the complete range from smooth surfaces to rough surfaces. It was found that the dimensionless load factor of rectangular piles showed a highly non-linear function with the aspect ratio of piles and a slightly non-linear function with the adhesion factor at the soil-pile interface. In addition, the dimensionless load factor of rectangular piles loaded along the major axis was significantly higher than that loaded along the minor axis until it converged to the same value at square piles. The solutions of finite element analyses were verified with the finite element limit analysis for selected cases. The empirical equation of the dimensionless load factor of rectangular piles was also proposed based on the data of finite element analysis. Because of the plane strain condition of the top view section, results can be only applied to the full-flow failure mechanism around the pile for the prediction of limiting pressure at the deeper length of a very long pile with full tension interface that does not allow any separation at soil-pile interfaces.

• Applied Chemistry for Engineering
• /
• v.10 no.5
• /
• pp.672-676
• /
• 1999

Adsorption isotherm is the most fundamental information in adsorption separation-process. Directly from the elution profile of a peak, the elution-curve method and frontal analysis(FA) were utilized to measure the adsorption isotherm in this work. Using RP-HPLC, sample and the buffer added in mobile phase were 5'-GMP and sodium phosphate, respectively. In this experimental condition, the retention time was decreased with increase in the injected mass of sample. And the front part of a peak was very stiff, so Langmuir adsorption isotherm might be applied. By the elution-curve method, the parameters used in the isotherm were obtained by optimization method, while by the FA, the concentrations of stationary phase were measured from the elution curve and the isotherm was determined by regression analysis. Compared to FA, the consumption of sample was less, and only one or two injections were needed by the elution-curve method. Finally, the effect of concentration of sodium phosphate in mobile phase on the parameters of the isotherm was investigated.

• Korean Institute of Interior Design Journal
• /
• v.25 no.1
• /
• pp.3-12
• /
• 2016

This study analyses characteristics of space to facilitate community centering on cases of collective houses in Japan and uses the results as basic data to activate collective houses as an alternative form of housing in our country. To identify the characteristics of space for active communities with collective living space, this study conducted a theoretical examination on collective houses and housing, derived territoriality, accessibility, comfort and safety as factors of community activation and analysed various cases, and the results are presented as follows: First, territoriality is a necessary condition for formation of community, and a confined and physical space. It indicates the proper size of a space and diverse spacial areas which meet the needs of residents with the proper size and amount of space (space which can accommodate diverse generations including women, the aged and the young, flexible space which changes according to the purposes and program, space which supports leisure and hobby activities, and space which can accommodate outsiders). Second, accessibility indicates an environment which supports residents' easy use of space. As the more accessible it is, the higher the frequency of its use, spatial factors (piloti, backyards, benches and tables) should be provided, community space should be arranged in a central or decentralized way and community living space should be made for each floor. As for exits, accessibility should be considered in every way; entrances connected with community spaces, open entrances and entrances accessible from outside or individual living spaces. Third, comfort satisfies the physical and mental needs of residents through separation of floors and flows between the community and individual spaces for privacy and formation of eco-friendly spaces including vegetable gardens, gardens and plant arrangements. Fourth, safety should be considered for a higher quality environment with psychological stability and comfort, for which the following are recommended: installation of hand-rails, removal of thresholds, spacial design for the socially weak, duplex and open type structures for community space, open stages and halls, as well as indoor and outdoor openness through the use of windows.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• v.y2005m4
• /
• pp.1-1
• /
• 2005

Japan Aerospace Exploration Agency(JAXA) has been conducting research and development of the Scramjet engines and their derivative combined cycle engines as hypersonic propulsion system for space access. Its history will be introduced first, and its recent advances, focusing on the engine performance progress, will follow. Finally, future plans for a flight test of scramjet and ground test of combined cycle engine will be introduced. Two types of test facilities for testing those hypersonic engines. namely, the 'Ramjet Engine Test Facility (RJTF)' and the 'High Enthalpy Shock Tunnel (HIEST)' were designed and fabricated during 1988 through 1996. These facilities can test engines under simulated flight Mach numbers up to 8 for the former, whereas beyond 8 for the latter, respectively. Several types of hydrogen-fueled scramjet engines have been designed, fabricated and tested under flight conditions of Mach 4, 6 and 8 in the RJTF since 1996. Initial test results showed that the thrust was insufficient because of occurrence of flow separation caused by combustion in the engines. These difficulty was later eliminated by boundary-layer bleeding and staged fuel injection. Their results were compared with theory to quantify achieved engine performances. The performances with regards to combustion, net thrust are discussed. We have reached the stage where positive net thrust can be attained for all the test coditions. Results of these engine tests will be discussed. We are also intensively attempting the improvement of thrust performance at high speed condition of Mach 8 to 15 in High Enthalpy Shock Tunnel (HIEST). Critical issues for this purposemay be air/fuel mixing enhancement, and temperature control of combustion gas to avoid thermal dissociation. To overcome these issues we developed the Hypermixier engine which applies stream-wise vortices for mixing enhancement, and the M12-engines which optimizes combustor entrance temperature. Moreover, we are going to conduct the flight experiment of the Hypermixer engine by utilizing flight test infrastructure (HyShot) provided by the University of Queensland in fall of 2005 for comparison with the HIEST result. The plan of the flight experiment is also presented.

• Korea-Australia Rheology Journal
• /
• v.20 no.2
• /
• pp.59-63
• /
• 2008

A theoretical model was developed to describe the flow behavior of a filled polymer in the packing stage of reaction injection molding and predict the residual stress distribution of thin injection-molded parts. The model predictions were compared with experiments performed for phenol-formaldehyde resin filled with wood dust and cured by urotropine. The packing stage of reaction injection molding process presents a typical example of complex non-isothermal flow combined with chemical reaction. It is shown that the time evolution of pressure distribution along the mold cavity that determines the residual stress in the final product can be described by a single 1D partial differential equation (PDE) if the rheological behavior of reacting liquid is simplistically described by the power-law approach with some approximations made for describing cure reaction and non-isothermality. In the formulation, the dimensionless time variable is defined in such a way that it includes all necessary information on the cure reaction history. Employing the routine separation of variables made possible to obtain the analytical solution for the nonlinear PDE under specific initial condition. It is shown that direct numerical solution of the PDE exactly coincides with the analytical solution. With the use of the power-law approximation that describes highly shear thinning behavior, the theoretical calculations significantly deviate from the experimental data. Bearing in mind that in the packing stage the flow is extremely slow, we employed in our theory the Newtonian law for flow of reacting liquid and described well enough the experimental data on evolution of pressure.

• The Journal of Korean Academy of Prosthodontics
• /
• v.34 no.2
• /
• pp.290-298
• /
• 1996

The effects of impression tray disinfection procedures on the bond strength of impression-material adhesive to two of types resin trays were evaluated with a tensile test. Autopolyme-rizing acrylic resin was formed into 1x1x1 cm cubes. A hook was attached to each cube with autopolymerizing acrylic resin. Perforated trays were fabricated with stops to maintain an even 3 cm of impression material over the resin block. Hook on the opposite side of the perforated tray permitted attachment of the metal plate to a mechanical testing machine. Before adhesive was applied, one third of the resin specimens were immersed in a 5% sodium hypochlorite solution : one third in a 2% glutaradehyde solution, and one third were kept in the "as fabricated" condition. Three products(Perfect ups, Exafine, and Exp-ress) of polyvynil siloxane impression material-adhesive system were evaluated. The resin-impression material-metal plate couples were attached to a mechanical testing machine and tensile forces were applied at a separation rate of 10 centimeters per second. The results were as follows; 1. Both disinfectant and adhesive had effects on bond strength values, but adhesive had more effect than disinfectant(p<0.01). However, there was no interaction between dinin-fectant and adhesive(p>0.01). 2. Mean bond strength values for the Perfect materials were about 85% less than that of the Exafine or the Express materials. However, there was no stastically significant difference between the mean bond strength values of the Exafine materials and the Express materials(p>0.05). 3. The use of disinfectants produced significant reduction in bond strength values(p<0.05). But there was no stastically significant difference between the mean bond strength values of the groups treated with disinfectants(p>0.05).

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.19 no.6
• /
• pp.647-656
• /
• 2008

In this paper, we present interference power distribution results when radio frequency identification(RFID) and ubiquitous sensor network(USN) systems share the $908.5{\sim}914MHz$ frequency bands. Average interference powers are obtained by simulation and statistical analysis, respectively. Simulation results are then verified by statistical analysis. According to the number of interferers and the diameter of the protection area, the cumulative density functions(CDFs) of interference power are simulated under the various conditions. From the simulation results, the probability that both USN and RFID systems meet the required maximal interference power levels is 95 % on condition that there are 1 low revered RFID reader and several USN nodes and that the minimum distance between a RFID reader and an USN node is greater than 1 m. Our results can be used as an basic research for coexistence analysis of RFID and USN systems in the $908.5{\sim}914MHz$ frequency bands.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.8 no.1
• /
• pp.179-186
• /
• 1998

We have been investigated the effects of the initial pH of the aquous solution, reaction temperature and time for the flaking of the soda-lime glass container. Flaking of glass occuurred in the cases of the $121^{\circ}C$, above pH 11 of solution with no $Mg^{2+}$ ions in solution. The pH of the solution approached to pH 10 under the conditions of below pH 9 of start solution. The flaking mechanism of the glass seem to be composed of formation of leached layer of $Ca^{2+}$ and $Na^{2+}$ ion and separation of these layers during the cooling by the difference of thermal expansion between leached layer and glass surface. The leaching of alkali ions in glass depends on the pH condition of the start solution and the temperature. In the case of $Mg^{2+}$ ions are added, $Mg^{2+}$ ions accelerate the flaking of the sodalime glasses and forms the magnesium silicate compound which result in the decrease of the pH of the solution.