• International Journal of Aeronautical and Space Sciences
• /
• 제9권1호
• /
• pp.111-120
• /
• 2008

A particle image velocimetry (PIV) technique was employed to investigate the effects of blowing jet on the flow characteristics over stationary and pitch-oscillating airfoils. The Reynolds number was $7.84{\times}10^5$ based on the chord length. It was found that for stationary airfoil cases, continuous and pulsating blowing jets successfully reduced separated wake region at high angles of attack. A comparison study of two different types of jet blowing indicated that pulsating jet is more effective than continuous jet for flow separation control. Pulsating leading-edge blowing postpones flow separation and increased stall angle of attack by $2^{\circ}{\sim}3^{\circ}$. For pitch-oscillating airfoil cases, the PIV results showed that blowing jet efficiently delays the separation onset point during pitch-up stroke, whereas it does not prevent flow separation during pitch-down stroke, even at angles of attack smaller than static ones.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회B
• /
• pp.2868-2872
• /
• 2007

In this study, a passive control using a boat-tail device is conducted for a three-dimensional car model in ground proximity. We consider various boat-tails and investigate the mechanism of drag reduction by them. By varying the length and slant angle of boat-tail, we obtain drag reductions up to 40%. From the oil-surface flow visualization and hot-wire measurement, the drag reduction by the boat-tail is characterized by the shear-layer instability and reattachment on the boat-tail, forming a small separation bubble at the upstream part of boat-tail surface, resulting in the delay of main separation and drag reduction. At high slant angles, the flow fully separates and drag is nearly same as that of no control.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2008년 영문 학술대회
• /
• pp.143-149
• /
• 2008

A numerical study was performed for a vane of a compressor with a high-turning angle and meridional divergence. At first, the effect of the suction position was discussed. Then, the optimal suction position was applied to the cascades with the aspect ratio of 2.53 and 0.3, respectively, to get the knowledge of the effect of the endwall boundary layer removal on the secondary flow along the blade height. At last, using the critical principles of the three-dimensional separation, the topological structures of the flow patterns of the body surfaces and the separation configurations were discussed in detail. The results show that the largest reduction of the total loss can be achieved when the suction slot is near the suction side. The topological structure as well as the separation configuration varies due to boundary layer removal, which restrains the flow separation at the corner and delays or depresses the separation on the suction surface. Compared with the original cascade, the cascade with the endwall boundary layer removal has a higher blade loading along the most span. Furthermore the flow loss decreases and distributes uniformly along the span.

• 한국수자원학회논문집
• /
• 제48권8호
• /
• pp.625-634
• /
• 2015

합류부에서의 지류의 합류각, 지류와 본류의 유량비에 추가하여, 본류 준설에 의한 하상고 불일치에 따른 다양한 양상의 분리구역의 특성을 CCHE2D 모형을 사용하여 분석하였다. 분리구역은 지류가 합류되어진 직후 단면에서의 유속이 0(영)인 경계로 정의하였다. 합류각 $30^{\circ}$ 이하에서는 분리구역이 형성되지 않았다. 유량비와 합류각 증가에 따른 분리구역의 크기는 일반적으로 증가하는 양상으로 나타났다. 준설 깊이비 증가에 따른 분리구역의 크기는 합류부 수용체의 증가에 기인한 지류에서의 상대적인 운동량의 감소로 인하여 감소되었다. 유량비와 합류각의 변화에 따른 분리구역의 수축지수를 규명하였고, 통수기능의 저하에 따른 배수영향을 확인하였다. 합류각, 유량비, 준설 깊이비에 따른 분리구역의 형상지수의 관계식을 제안하였다.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2004년도 춘계학술대회
• /
• pp.1619-1624
• /
• 2004

Experimental study of separated flow over a NACA0012 airfoil is conducted at $Re=2{\times}10^5$ when periodic wakes pass over the airfoil. The wakes are periodically generated by circular cylinders upstream of the airfoil. The measurement of surface pressure and surface visualization at various angles of attack are carried out without and with passing wakes. Without passing wakes, a separation bubble at the leading edge of the suction surface is formed at an angle of attack, found from a local plateau in the streamwise pressure distribution and two distinct lines in the surface flow visualization. With passing wakes, however, the bubble disappears. Owing to passing wakes, the lift increases at high angle of attack and the angle of stall also increases.

• 한국항공우주학회지
• /
• 제32권8호
• /
• pp.47-53
• /
• 2004

타원형 날개꼴의 공력 특성에 브로잉 제트 방식과 제트 방향의 영향에 대하여 실험을 통하여 연구를 수행하였다. 본 연구는 타원형 날개꼴의 박리제어에 있어서 브로잉 제트적용에 관한 기본 데이터를 축적하는데 목적을 두었다. 본 연구에서는 날개면에서의 압력 분포, 브로잉 제트 출구에서의 유속 분포 및 공력 자료를 제공하였다. 타원형 날개꼴에 대한 실험은 레이놀즈수 $8.22{\times}10^5$에서 수행하였다. 펄스제트는 후실속각 이후에 공력 특성을 향상시키는 효과를 보여 주었다. 즉, 펄스제트는 감소된 질량유동율로 상당히 높은 양력을 발생하였다. 제트 방향도 박리제어의 주요 파라미터임을 보였다. 양의 제트각은 박리를 지연시키거나 억제하였고, 음의 제트각은 박리를 오히려 촉진시켰다.

• 대한기계학회논문집B
• /
• 제24권2호
• /
• pp.260-269
• /
• 2000

Oil-film flow visualizations and three-dimensional flow measurements have been conducted in the downstream region of a butterfly-type valve used in air-conditioning systems, with the variation of a disk open angle. The flow visualizations in the flow symmetry plane show that there are a pair of counter-rotating separation/recirculation zones as wall as two jet-like near-wall flows. These flow disturbances are strongly depends on the disk open angle. Based on the flow visualization, a qualitative flow model is suggested in the near-field and downstream region of the valve disk. For a small disk open angle, the mean velocities and turbulent intensities have relatively small values in the near-field of the valve disk, but they do not show uniform distributions even in some downstream region. With an increment of the disk open angle, mean velocity variations and turbulent intensities are greatly increased in the immediate downstream region, but uniform distributions are quickly resumed as departing from the valve disk. The mass flow rate remains nearly constant for the disk open angles less than 30 degrees, meanwhile it strongly depends on the disk open angles between 45 and 75 degrees. The pressure loss is found to be about zero for the disk open angles less than 45 degrees, but is substantially increased for those larger than 75 degrees.

• Advances in aircraft and spacecraft science
• /
• 제1권4호
• /
• pp.443-454
• /
• 2014

An experimental study was conducted to investigate the effect of Reynolds number on compressible convex-corner flows, which correspond to an upper surface of a deflected flap of an aircraft wing. The flow is naturally developed along a flat plate with two different lengths, resulting in different incoming boundary layer thicknesses or Reynolds numbers. It is found that boundary layer Reynolds number, ranging from $8.04{\times}10^4$ to $1.63{\times}10^5$, has a minor influence on flow expansion and compression near the corner apex in the transonic flow regime, but not for the subsonic expansion flow. For shock-induced separated flow, higher peak pressure fluctuations are observed at smaller Reynolds number, corresponding to the excursion phenomena and the shorter region of shock-induced boundary layer separation. An explicit correlation of separation length with deflection angle is also presented.

• Ocean Systems Engineering
• /
• 제12권3호
• /
• pp.335-358
• /
• 2022

Hydrodynamic field alteration around a cylindrical pier using a curved vane is numerically investigated. The curved vane with various angles ranged from 10 to 220 degree is placed at the upstream of the cylindrical pier. Laminar flow is adopted in order to perform the steady-state analysis. It is found that the flow separation leads to the formation of four bubbles depending on the value of the curved vane angle. Two bubbles are located in the region between the rear of the curved vane and the leading surface of the cylindrical pier, while the remaining two bubbles are located at the wake zone behind the cylindrical pier. Numerical analysis is performed to reveal the hydrodynamic field and influence of curved vane on the formation and evolution of the bubbles. It is found that the center and size of the bubble depend mainly on the value of the curved vane angle. It is observed that the flow velocity vector shows clearly the alteration in the flow velocity direction especially at the leading surface and rear surface of the curved vane owing to the occurrence of flow separation and flow dissipation along the circumference of the vane.

• 한국정밀공학회지
• /
• 제4권1호
• /
• pp.42-52
• /
• 1987

Experimental investigation on the characteristics of the air flow around a square prism located in a uniform flow with various angles of attack was carried out. Experimental results were obtained for the angle of attack from 0 .deg. to 45 .deg. and for Reynolds No. from $2.6{\times}^4$to $12.8^4$. Seperation and reattachment was occurred on the forward face (face AB). Reattachment phenomenon was not developed in the range of attack angle lower 13 .deg. . But, for the range, 13 .deg. .approx. 35 .deg. , the reattachment developed and its position was moved forward the angle of attack increases. Pressure distributions on the reattachment face has a maxium at the reattachment point and a minimum at the separation point. Pressurea on two back faces are nearly symmetric in spite of the changes of the angle of attack and are influenced by the turbulence in rearward flow field.