• International Journal of Fluid Machinery and Systems
• /
• v.3 no.3
• /
• pp.260-270
• /
• 2010

Reducing the losses of the tip clearance flow is one of the keys in an unshrouded centrifugal compressor design and development because tip clearances are large in relation to the span of the blades and also centrifugal compressors produce a sufficiently large pressure rise in single stage. This problem is more acute for a low flow high-pressure ratio impeller design. The large tip clearance would cause flow separations, and as a result it would drop both the efficiency and surge margin. Thus a design of a high efficiency and wide operation range low flow coefficient centrifugal compressor is a great challenge. This paper describes a recent development of high efficiency and wide surge margin low flow coefficient centrifugal compressor. A viscous turbomachinery optimal design method developed by the authors for axial flow machine was further extended and used in the centrifugal compressor design. The compressor has three main parts: impeller, a low solidity diffuser and volute. The tip clearance is under a special consideration in this design to allow impeller insensitiveness to the clearance. A patented three-dimensional low solidity diffuser design method is used and applied to this design. The compressor test results demonstrated to be successful to extend the low solidity diffusers to high-pressure ratio compressor. The compressor stage performance showed the total to static efficiency of the compressor being about 85% and stability range over 35%. The test results are in good agreement with the design.

• Journal of Institute of Convergence Technology
• /
• v.5 no.1
• /
• pp.27-31
• /
• 2015

A Pin-fin array is widely used to enhance the heat transfer in the internal cooling passage. The heat transfer distribution around the pin-fin is varied by the horseshoe vortex and flow separation. The difference of heat transfer coefficient induces the large thermal stress, which is one of the major reasons to break of hot components. So, it is required to enhance the heat transfer on the back side of pin-fin to solve the thermal stress problem. This study suggests the pin-fin with inclined jet hole and complex pin-fin/dimple array to enhance the heat transfer on the back side of pin-fin. The heat transfer coefficient is predicted by the numerical analysis, which is performed by CFX 14.0. The numerical results are obtained at Reynolds number, 10,000. The results show that the heat transfer on the back side of pin-fin is increased in both cases. Beside, the wake, which comes from dimple and jet, helps to develop the horseshoe vortex and increase the heat transfer on the next row pin-fin.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.15 no.3
• /
• pp.143-150
• /
• 2003

Based on the eigenfunction expansion method, the interaction between monochromatic waves and a partially immersed slotted plate with a back wall has been investigated. Analytical results show that the reflection coefficients by a partially immersed slotted plate depend on the porosity, immersed depth, chamber width, incidence angle and wave frequency. It is found that the reflection coefficient has minimum value within entire frequency range when the porosity has optimal value 0.1. Comparison between the analytical results and the experimental results(Zhu,2001) of reflection coefficients is made for various chamber widths, immersed depths and wave periods with good agreement. The present analytic method can account adequately for energy dissipation caused by flow separation behind a slotted plate and provide the design informations for the construction of slit caisson breakwater.

• Wind and Structures
• /
• v.13 no.2
• /
• pp.127-144
• /
• 2010

Pressure measurements on static and autorotating flat plates have been recently reported by Lin et al. (2006), Holmes, et al. (2006), and Richards, et al. (2008), amongst others. In general, the variation of the normal force with respect to the angle of attack appears to stall in the mid attack angle range with a large scale separation in the wake. To date however, no surface pressures have been measured on auto-rotating plates that are typical of a certain class of debris. This paper presents the results of an experiment to measure the aerodynamic forces on a flat plate held stationary at different angles to the flow and allowing the plate to auto-rotate. The forces were determined through the measurement of differential pressures on either side of the plate with internally mounted pressure transducers and data logging systems. Results are presented for surface pressure distributions and overall integrated forces and moments on the plates in coefficient form. Computed static force coefficients show the stall effect at the mid range angle of attack and some variation for different Reynolds numbers. Normal forces determined from autorotational experiments are higher than the static values at most pitch angles over a cycle. The resulting moment coefficient does not compare well with current analytical formulations which suggest the existence of a flow mechanism that cannot be completely described through static tests.

• Proceedings of the KSME Conference
• /
• 2001.11b
• /
• pp.124-130
• /
• 2001

The heat transfer and flow measurements were made on a cylindrical pedestal mounted on a flat plate with a turbulent impinging air jet. The heat transfer coefficient distributions on the flat plate were measured using the shroud-transient technique and liquid crystal was used to measure the surface temperature. The jet Reynolds number (Re) is 23,000, the dimensionless nozzle-to-surface distance (L/d) from 2 to 10, the dimensionless pedestal diameter-to-height (H/D) from 0 to 1.5, the dimensionless 2nd pedestal diameter-to-height ($H/D_2$) from 0 to 0.4 and the distance from the stagnation point to 2nd pedestal (p/D). The results show that for H/D = 0.5 to 1.5, the Nusselt number distributions on the plate surface exhibit a maximum between $r/d\;{\cong}\;1.0$ and 1.5. The presence of the pedestal appears to cause the flow separation and reattachment on the plate surface, which results in the maximum heal transfer coefficient. Also, for p/D = 2.5 and $H/D_2$ = 0.3, the local Nusselt number in the region corresponding to $r/d\;{\cong}\;1.1$ was increased up to 50% compared to that for $H/D_2=0$.

• Journal of Mechanical Science and Technology
• /
• v.18 no.2
• /
• pp.272-285
• /
• 2004

The losses at off-design points from a compressor cascade occur due to the deviation from a design incidence angle at the inlet of the cascade. The self-noise from the blade cascade at off-design points comes from a separated boundary layer and vortex sheddings. If the incidence angle to the cascade increases, stalling in blades may occur and the noise level increases significantly. This study applied Large-Eddy Simulations (LES) using deductive and deductive dynamic SGS models to low Mach-number, turbulent flow with each incidence angle to the cascade ranging from -40$^{\circ}$ to +20$^{\circ}$ and compared numerical predictions with measured data. It was observed that the oscillating separation bubbles attached to the suction surface do not modify wake flows dynamically for cases of negative incidence angles. However, an incidence angle greater than 8$^{\circ}$ caused a separated vortex near the leading edge to be shed downstream and created stalling. The computed performance parameters such as drag coefficient and total pressure loss coefficient showed good agreement with experimental results. Noise from the cascade of the compressor is summarized as sound generated by a structure interacting with unsteady, turbulent flows. The hybrid method using acoustic analogy was observed to closely predict the measured overall sound powers and directivity patterns at design and off-design points of blade cascade.

• Clean Technology
• /
• v.14 no.1
• /
• pp.47-52
• /
• 2008

Among various mass transfer models to express adsorption rates for any adsorption processes, the linear driving force (LDF) model is used most. The present investigation aims at finding whether this model may be applied to real adsorption process for separation and removal of benzene. Comparison of numerical simulation results calculated by the LDF model with experimental data allowed us to find the mass transfer coefficients that are most appropriate for a specific adsorption process. Various breakthrough curves were obtained from experiments performed at many different temperatures and pressures, which in turn produced suitable mass transfer coefficients. These dependencies of mass transfer coefficient on temperature and pressure were represented by an Arrhenius type- and a power law type empirical equation, respectively.

• Biotechnology and Bioprocess Engineering:BBE
• /
• v.6 no.6
• /
• pp.426-432
• /
• 2001

Perstractive fermentation is a good way to increase the productivity of bioreactors. Us-ing Propionibacteria as the model system, the feasibility of using supported emulsion liquid mem-brane(SELM) fro perstractive fermentation is assessed in this study. Five industrial solvents were considered as the solvent for perparing the SELM. The more polar a solvent, is the higher the par-tition coefficeint However, toxicity of a solvent also increases with its polarity. CO-1055(indus-trial decanol/octanol blend)has the highest partition coefficient toward propionic acid among the solvents that has no molecular toxicity toward Propionibacteria, A preliminary extraction study was conducted using tetradecane as solvent in a hydrophobic hollow fiber contactor. The results confirmed that SELM eliminates the equilibrium limitation of conventional liquid-liquid extrac-tion and allows the use of a non-toxic solvent with low partition coefficient.

• Journal of Korean Society of Water and Wastewater
• /
• v.33 no.2
• /
• pp.103-110
• /
• 2019

Management of stormwater runoff is considered a nationwide challenge. To deal with this challenge, many researches have been conducted to study initial stage of stormwater fee imposition. The objective of this study was to recommend a framework for stormwater fee imposition not only for funding the stormwater management programs but also for encouraging people to decrease impervious area. This study focused on, regulations, financial resources and international cases related to stormwater runoff management. Polluter pays principle, which is generally recognized environmental policy principle is regarded the basis of stormwater fee imposition. Three components suggested for the stormwater rate structure are 1) stormwater utility revenue requirement, 2) billable equivalent stormwater unit, 3) system unit cost. The key point of stormwater rate structure is the "Equivalent Residential Unit(ERU)". The concept of an ERU is one residential area with a runoff coefficient. The runoff coefficient is that portion of rainfall that becomes runoff rather than infiltrating into the ground. In addition to this, this study took into account the observed data simulation for the separation of stormwater treatment expenditure from the comprehensive wastewater treatment cost.

• Wind and Structures
• /
• v.32 no.3
• /
• pp.239-248
• /
• 2021

In this study, three airfoil families, NACA, FX and S, in each case three from each series with different shapes were investigated at different angles of attack using Computational Fluid Dynamics (CFD) method. To verify the CFD model, simulation results of the NACA 0012 airfoil was compared against the available experimental data and k-ω SST was used as the turbulence model. Lift coefficients, lift to drag ratios and pressure distributions around airfoils were obtained from the CFD simulations and compared each other. The simulations were performed at three Reynolds numbers, Re=2×105, 1×106and 2×106, and angle of attack was varied between -6 and 12 degrees. According to the results, similar lift coefficient values were obtained for symmetric airfoils reaching their maximum values at similar angles of attack. Maximum lift coefficients were obtained for FX 60-157 and S 4110 airfoils having lift coefficient values around 1.5 at Re=1×106 and 12 degrees of angle of attack. Flow separation occurred close to the leading edge of some airfoils at higher angles of attack, while some other airfoils were more successful in keeping the flow attached on the surface.