• Korean Journal of Geomatics
• /
• v.3 no.1
• /
• pp.23-32
• /
• 2003

Rigorous sensor and dynamic modeling techniques are required if spatial information is to be accurately extracted from video imagery. First, a mathematical model for an uncalibrated video camera and a description of a bundle adjustment with added parameters, for purposes of general block triangulation, is presented. This is followed by the application of invariance-based techniques, with constraints, to derive initial approximations for the camera parameters. Finally, dynamic modeling using the Kalman Filter is discussed. The results of various experiments with real video imagery, which apply the developed techniques, are given.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.27 no.12
• /
• pp.825-830
• /
• 2014

$[(Co_{1-x}Cu_x)_{0.2}(Ni_{0.3}Mn_{0.7})_{0.8}]_3O_4$ ($0{\leq}x{\leq}1$) thin films prepared by metal organic decomposition process were fabricated on SiN/Si substrate for infrared sensor application. Their structural and electrical properties were investigated with variation of Cu dopant. The $[(Co_{1-x}Cu_x)_{0.2}(Ni_{0.3}Mn_{0.7})_{0.8}]_3O_4$ (CCNMO) film annealed at $500^{\circ}C$ exhibited a dense microstructure and a homogeneous crystal structure with a cubic spinel phase. Their crystallinity was further enhanced with increasing doped Cu amount. The 120 nm-thick CCNMO (x=0.6) thin film had a low resistivity of $53{\Omega}{\cdot}cm$ at room temperature while the Co-free film (x=1) showed a significantly decreased resistivity of $5.9{\Omega}{\cdot}cm$. Furthermore, the negative temperature coefficient of resistance (NTCR) characteristics were lower than $-2%/^{\circ}C$ for all the specimens with $x{\geq}0.6$. These results imply that the CCNMO ($x{\geq}0.6$) thin films are a good candidate material for infrared sensor application.

• Journal of Sensor Science and Technology
• /
• v.15 no.2
• /
• pp.127-133
• /
• 2006

Recent studies demonstrated the ability of carbon nanotube (CNT) to promote electron transfer reactions of important compounds and to impart higher stability onto electrochemical sensors. CNT-based sensors measured by hydroxyl radical concentration or pH value suggest great promise for biosensors. This paper describes a new method for fabricating a very simple and inexpensive pH sensor compose of single walled-carbon nanotubes (SW-CNTs) using an ultra-precision spray. CNT-based sensor shows pH sensitivity in buffer solution at different pH range. Our experimental results show the sensor responses to pH buffer solution and the conductance of depends on the pH values. These results support application possibility of SW-CNTs based pH sensor for mass production.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2017.10a
• /
• pp.465-469
• /
• 2017

In this paper we propose a human body tracking method for application of smartphones. The conventional human body tracking method is divided into a sensor-based method and a vision-based method. The sensor-based methods have a weakness in that tracking accuracy is low due to cumulative error of position information. The vision-based method has no cumulative error, but it requires reduction of the computational complexity for application of smartphone. In this paper we use the improved HOG algorithm as a human body tracking method for application of smartphone. The improved HOG algorithm is implemented through downsampling and frame sampling. Gaussian pyramid is applied for downsampling, and uniform sampling is applied for frame sampling. We measured the proposed algorithm on two devices, four resolutions, and four frame sampling intervals. We derive the best detection rate among downsampling and frame sampling parameters that can be applied in realtime.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.12 no.5
• /
• pp.261-265
• /
• 2012

The applications of augmented reality technology is increasing in the several field by IT convergence and we find augmented reality application easily in the smart device application area. And then, to attempt to use augmented reality technology in advantage, exhibitions and performances was activated. However, it less than other fields of augmented reality technology expertise yet. Among them services to Use in fusion with monitoring are lacking. In this paper, we proposed the augmented reality monitoring technology based on smart device. It is able to incorporate QR-code which is already building for the purpose of advertising promotional materials with augmented reality technology in many areas. Therefore, it is able to utilize unattended building or automation equipment facilities using QR-code and environmental monitoring sensor in the industry.

• Journal of Communications and Networks
• /
• v.17 no.5
• /
• pp.453-462
• /
• 2015

Body area networks (BANs) have emerged as an enabling technique for e-healthcare systems, which can be used to continuously and remotely monitor patients' health. In BANs, the data of a patient's vital body functions and movements can be collected by small wearable or implantable sensors and sent using shortrange wireless communication techniques. Due to the shared wireless medium between the sensors in BANs, it may be possible to have malicious attacks on e-healthcare systems. The security and privacy issues of BANs are becoming more and more important. To provide secure and correct association of a group of sensors with a patient and satisfy the requirements of data confidentiality and integrity in BANs, we propose a novel enhanced secure sensor association and key management protocol based on elliptic curve cryptography and hash chains. The authentication procedure and group key generation are very simple and efficient. Therefore, our protocol can be easily implemented in the power and resource constrained sensor nodes in BANs. From a comparison of results, furthermore, we can conclude that the proposed protocol dramatically reduces the computation and communication cost for the authentication and key derivation compared with previous protocols. We believe that our protocol is attractive in the application of BANs.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.27 no.1
• /
• pp.92-98
• /
• 2013

In this paper, Completely beyond the existing conventional Guard Light management system, introduced the 447Mhz band wireless sensor network Guard Light to manage efficiently the shape of the new system is proposed. In addition, about wireless sensor network technology, control server technology, application layer protocol technology etc which is core technology for the proposed system configuration, it was verified by the design and experiment. Especially studying wireless Guard Light System(about 1,700 node configuration) commercially installed in the Daegu area as a results of the study, I would like to prove the effectiveness of the study.

• Journal of Sensor Science and Technology
• /
• v.28 no.4
• /
• pp.231-235
• /
• 2019

We investigated the facile and effective strategy for sensitive and selective $C_2H_5OH$ sensors based on the In-decorated NiO nanoigloos. The In-decorated NiO nanoigloos is fabricated by RF sputtering using 750 nm-diameter polystyrene beads using a soft-template. The morphological evolution based on the Van der Drift model was generated through a heterojunction between In metal and NiO, resulting in a pyramidal rough surface. Upon decorating the In on the NiO surface, high sensitivity and selectivity to $C_2H_5OH$ were observed, and gas sensing mechanism was demonstrated by a high surface-to-volume and double Schottky barrier. We are confident that the method presented in this study will have a significant impact on the fabrication of effective nanostructures and their application for the gas sensors.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.28 no.5
• /
• pp.421-426
• /
• 2008

The magnetic bio-sensor used the PHR (planar hall resistance) effect generated by the free layer in spin-valve giant magnetoresistance structure of Ta/NiFe/CoFe/Cu/NiFe/IrMn/Ta. The PHR element with micrometer size was fabricated through the photolithograph and dry etching process. The PHR signal with magnetic field was measured under the conditions of with and without single magnetic bead. A single magnetic bead of diameter $2.8\;{\mu}m$ was successfully detected using the PHR sensor. Therefore, the high resolution PHR sensor can be applied to bio-sensor application utilizing the output voltage variation of the PHR signals in the presence and absence of a single magnetic bead.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.24 no.5
• /
• pp.476-486
• /
• 2004

This paper is the second part of the study on the development of a smart active layer (SAL) sensor, which consists of two parts. As mentioned in the first paper, structural health monitoring (SHM) is a new technology that is being increasingly applied at the industrial field as a potential approach to improve cost and convenience of structural inspection. Recently, the development of smart sensor is very active for real application. This study has focused on preparation and application study of SAL sensor which is described with regard to the theory and concept of the SAL sensor in the first paper. In order to detect elastic wave, smart piezoelectric sensor, SAL, is fabricated by using a piezoelectric element, shielding layer and protection layer. This protection layer plays an important role in a patched network of distributed piezoelectric sensor and shielding treatment. Four types of SAL sensor are designed/prepared/tested, and these details will be discussed in the paper In this study, SAL sensor ran be feasibly applied to perform structural health monitoring and to detect damage sources which result in elastic waves.