• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 1997년도 고액공존금속의 성형기술 심포지엄
• /
• pp.148-159
• /
• 1997

In this study, microstructure, size of primary $\alpha$, solid fraction and hardness of A356 Al alloy, were investigated. Semi-solid A356 allos were obtained by semi-solid continuous casting apparatus consists of melting furnace, formation apparatus of granular primary $\alpha$ and continuous casting apparatus. Size of promary $\alpha$ and fraction solid were decreased with decreasing temperature, and with increasing volume of cooling water. At the cooling water temperature of 15$^{\circ}C$ and cooling water volume of 18.2$\ell$/min, the sizes of primary $\alpha$ phases were decreased up to 40${\mu}{\textrm}{m}$, and fraction solid was 0.68.

• 소성∙가공
• /
• 제4권3호
• /
• pp.233-244
• /
• 1995

Rolling force in the direct rolling(or twin-roll strip continuous casting) process fo semi-solid material has been computed using rigid-viscoplastic finite element method. Temperature distributions for calculations of rolling force and roll deformation are obtained from thermofluid analysis. Three dimensional roll deformation analysis has also been performed by using commercial package ANSYS. From the results, behavior of metal flow, rolling force and roll deformation have been investigated according to the process conditions of semi-solid direct rolling.

• 소성∙가공
• /
• 제23권3호
• /
• pp.178-183
• /
• 2014

Continuous casting is a process where molten metal is solidified into a semi-finished billet on a large scale with either a rectangular or round cross section for subsequent processing. The use of continuous casting provides an opportunity for producing material on a practical industrial scale with lower cost than conventional casting. In the current study, the material was fabricated by continuous casting and subsequent extrusion. Tensile tests were conducted on continuous cast ZK60A after extrusion over a range of strain rates at temperatures from 473K to 623K. The alloy exhibits a quasi-superplastic behavior with a maximum recorded elongation of ~250% at 523K when tested with an initial strain rate of $10^{-5}/s$. The experiments give a strain rate sensitivity exponent of 0.3~0.4 and an activation energy of 108 kJ/mol. From the current investigation, it was found that the high-temperature plastic flow of the ZK60A is controlled by a dislocation viscous glide mechanism.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 1998년도 춘계학술대회논문집
• /
• pp.138-143
• /
• 1998

The continuous casting process has been adopted increasingly in recent years to save both energy and labor. It has experienced a rapid development in the production of semi-finished steel products, replacing the conventional route of ingot casting plus rolling. To achieve this good merit, however, more studies about a heat transfer mechanism between roll and slab are needed. So this paper shows the results of the deformation behavior of steel cast slabs, which are about the solidification and heat transfer. This study is used to prevent internal cracks of a slab in a bending and unbending zone. The value of moving strand shell bulging between two supporting rollers under ferrostatic pressure and slab-self weight has been computed in terms of creep and elastic-plasticity. The high strand distributions in solidified shell undergoes a series of bulging are calculated with boundary condition a very closed to continuous steel cast slabs productions.

• 대한기계학회논문집A
• /
• 제24권7호
• /
• pp.1650-1660
• /
• 2000

Continuous casting process has been adopted increasingly in recent years to save both energy and labor. It has experienced a rapid development in the production of semi-finished steel products, rep lacing the conventional route of ingot casting and rolling. In order to achieve this merit, however, more studies about the mechanism between roll and slab are needed. In this paper, a dynamic bulging in steel cast slabs was simulated by considering the solidification and heat transfer. This study is to prevent internal cracks of a slab in a bending and unbending zone. The value of moving strand shell bulging between two supporting rollers under the ferrostatic pressure and slab-self weight has been calculated in terms of creep and elasto-plasticity. The strain and strain rate distributions in solidified shell undergoing a series of bulging are calculated with working boundary conditions.

• 한국재료학회지
• /
• 제10권2호
• /
• pp.117-123
• /
• 2000

본 연구에서는 반응고 Al합금을 얻기 위해서 3상 2극의 전자교반장치를 이용하였으며, 주입온도와 주입전압을 변화시켜 Al합금의 초정입자크기, aspect ratio, 표준편차, 경도 및 공정 Si 입자의 크기 및 형상 변화를 조사하였다. 같은 주입온도에서는 주입전압이 증가함에 따라 aspect ratio, 표준편차 및 초정입자의 크기는 감소되었다. 전자교반식 수평연속주조방법에 의한 Al 합금의 최적제조 조건은 주입전압 220V, 주입온도 68$0^{\circ}C$이었으며, 이 조건에서 초정입자의 크기는 54$\mu\textrm{m}$이었고, aspect ratio는 1.56이었으며 그 표준편차는 0.4이었다. 그리고 공정 Si의 크기는 0.5$\mu\textrm{m}$이었으며 제조된 Al합금의 경도는 72.1 Hv를 나타내었다. 본 연구를 위해 제작된 3상 2극 전자교반장치에 의해서 매우 낮은 aspect ratio 및 표준편자를 갖는 반응고 A356 Al합금을 제조할 수 있었다.

• 한국정보처리학회논문지
• /
• 제7권2호
• /
• pp.477-487
• /
• 2000

본 논문에서는 체적 시각화 과정을 이론적으로 고찰하여 시각화 모델을 제시하고 그 모델로 유도된 관계로부터 미분 방정식을 이용하여 분석적 체적 시각화 해법을 구하였다. 이 분석적 방법을 제적 시각화의 대표적인 방법인 Levoy의 이산적 광선 추적법과 비교하여 본 연구에서 제시한 방법의 특수한 형태가 Levoy의 이산적 방법임을 보였다. 그리고 체적 데이터를 시각화기 위해서는 사용자가 시각화하기를 원하는 부위를 선택하고 이 부분만을 추출하는 영역 분할 작업이 필요하다. 본 논문에서는 영역확장법에 기반을 둔 효율적인 3차원 영역 분할 기법을 개발하여 위의 분석적인 방법을 이용하여 3차원 제적 데이터의 시각화를 위한 시스템을 구현하였다. 그리고 본 접근법에 대한 의의와 유용함에 대한 가설적인 결론을 구현된 시스템을 이용한 실험에 근거하여 유도하였다. Lovoy의 이산적인 방법과 분석적인 방법을 같은 데이터에 대해 3차원 영역 분할 수행 후 적용한 실험은 분석적인 방법이 이산적인 방법에 비해 렌더링된 이미지의 질이 더 좋음을 보여준다.

• 한국주조공학회지
• /
• 제39권1호
• /
• pp.7-13
• /
• 2019

Few studies of large blooms over 700 mm thick among those used for the forging of raw materials have been reported. The cooling rate difference between the surface and the center of a large bloom is large, and the degradation of the mechanical properties is likely in cases involving excessively coarse precipitates resulted from the slow cooling rate of a large bloom after casting. Therefore, a schematic investigation of the growth behaviors of precipitates while varying their locations in blooms is necessary. The dissolution behaviors of precipitates were investigated by simulating a reheating process during which the bloom is heated to a high temperature. The segregation behavior of the as-cast large bloom was also investigated. Reheating specimens were obtained after an isothermal heat treatment at $1150^{\circ}C$ with various holding times to simulate the reheating process, with the samples undergoing a subsequent water quenching step. The precipitates were extracted using an electrolytic extractor and a particle size analysis was conducted with the aid of SEM, EDS, and TEM. In the present work, Al oxide, MnS and Nb carbide were mainly observed.

• 소성∙가공
• /
• 제11권1호
• /
• pp.24-35
• /
• 2002

Recent trend and future prospect of flat rolling of steel has been summarized based on the earlier reports. Key technology in the plate rolling is to have ultra fine microstructure having high resistance against crack propagation during application. Heavy accelerated cooling facility and high power rolling mill will be helpful to develope the high toughness steel. Precise modeling of properly prediction based on deformation and transformation imposed on microstructure of steel during processing is highly anticipated. For the hot strip rolling process, new trend is lies on the production of ultra-thin gauged hot strip to substitute cold rolled strip. For the substitution of cold rolled strip into hot rolled strip widely, high formable property of hot strip is highly required. For the formabilit, the ferritic rolling of extra low carbon steel under high lubricated condition is essential. Recently introduced semi-continuous thin slab and rolling mill line is very plausible to develope those kinds of products easily In the view groin facility combination. New idea to modify the existing continuous hot strip mill line to produce the ultra thin-gauged hot strip in an economic way is suggested in this report.

• 소성∙가공
• /
• 제15권6호
• /
• pp.421-427
• /
• 2006

Drawing process of Al-1%Si bonding wire considering fine Si particle is analyzed in this study using FE-simulation. Al-1%Si boding wire requires electric conductivity because Al-1%Si bonding wire is used for interconnection in semiconductor device. About 1% of Si is added to Al wire for dispersion-strengthening. Distribution and shape of fine Si particle have strongly influence on the wire drawing process. In this study, therefore, the finite-element model based on the observation of wire by continuous casting is used to analyze the effect of various parameters, such as the reduction in area, the semi-die angle, the aspect ratio, the inter-particle spacing and orientation angle of the fine Si particle on wire drawing processes. The effect of each parameter on the wire drawing process is investigated from the aspect of ductility and defects of wire. From the results of the analysis, it is possible to obtain the important basic data which can be guaranteed in the fracture prevention of Al-1 %Si wire.