• Journal of The Korean Society of Grassland and Forage Science
• /
• v.15 no.3
• /
• pp.198-206
• /
• 1995

Baled silage making(BS) of selected forage crops was discussed during 1991-1993, to determine the best cutting time of the plants for BS production, BS yields and silage quality. Seven species of forage crops and pasture grasses(rye, barley, spring oat, Italian ryegrass, orchardgrass, alfalfa and grass-legume pasture mixtures) were harvested at different stage of growth from young plant to physiological maturity, and baled in a self constructed square baling chamber. Each bales, measured 90cm length, 60cm width and 50cm height, were wrapped with 0.05mrn thick polyethylene plastic film, and stored in stack silo. Each bales were weighed between 15-20 kg in dry matter basis. The effects of pre wilting and formic acid addition on the silage quality of young plant materials, which contained high water concentration, was also evaluated during the experiment. Rye plant including of barley and spring oat were evaluated as a good materials for baled silage making. Fodder rye produced high quality BS with a value of silage quality point 84(Flieg's point) when the plant harvested at stage of greatest dry matter accumulation by 12.64 tonha. The best quality BS of barley was obtained at stage of hard dough to yellow stage by 11.9 ton/ha dry matter yield and 81 point silage quality. Italian ryegrass and pasture grasses including of orchardgrass, alfalfa and grass-legume pasture mixtures procuced also high quality bale silage by harvesting at stage of late blooming. However pre witting operation and formic acid addition was required for BS production of grass materials because of high water contents. Water contents of Italian ryegrass and other pasture species ranged 18.9%(Italian) to 20.8%(alfalfa). Silage quality point of Italian BS harvested at late blooing was increased from 72 to 88 by 1/2-one day pre wilting and 0.3% formic acid treatment. Silage quality of young plant materials of rye and other forage crops, barley and spring oat were also improved markedly through the pre wilting treatment and formic acid addition.

• Korean journal of applied entomology
• /
• v.54 no.4
• /
• pp.401-407
• /
• 2015

This study describes the development of a method for monitoring Aphis gossypii in greenhouse cucumber fields that was used during 2013 and 2014. The dispersion pattern of A. gossypii was determined by commonly used methods: Taylor's power law (TPL) and Iwao's patchiness regression (IPR). The sample unit was determined by linear regression analysis between mean density of sample unit versus whole plant. The optimum sample unit for different plant growth stages was two leaves (median and the lowest + 1 leaf) when the total number of leaves was less than nine, and three leaves (4th, 7th from canopy, and the lowest +1 leaf) when the total number of leaves was greater than nine. A. gossypii showed an aggregated distribution pattern, as the slopes of both TPL and IPR lines were greater than 1. TPL provided a better description of the mean-variance relationship than did IPR. The slopes and intercepts of TPL and IPR from leaf samples did not differ between the surveyed years. Fixed precision levels (D) for a sequential sampling plan were developed using Green's and Kuno's equations based on the number of aphid in a leaf sample. Green's method was more efficient than Kuno's to stop sampling. The number of samples needed to estimate the density of A. gossypii increased at higher D levels and lower mean densities. The cumulative number of aphids needed to stop sampling increased at higher D levels and with fewer plants sampled. Thus to estimate 10 aphids per leaf, 13 plants needed to be sampled, and the cumulative number of aphids to stop sampling was 131.

• 한국사회정책
• /
• v.24 no.1
• /
• pp.33-66
• /
• 2017

Based on the premise that the systematic career process of workers in the general labor market was one of core elements of successful achievements and their establishment both at the individual and organizational level, this study set out to conduct empirical analysis of factors influencing the subjective career success of disabled workers in competitive employment at the multi-dimensional levels of individuals and organizations(corporations) and thus provide practical implications for the career management directionality of their successful vocational life with data based on practical and statistical accuracy. For those purposes, the investigator administered a structured questionnaire to 126 disabled workers at 48 companies in Seoul, Gyeonggi, Chungcheong, and Gangwon and collected data about the individual and organizational characteristics. Then the influential factors were analyzed with the multilevel analysis technique by taking into consideration the organizational effects. The analysis results show that organizational characteristics explained 32.1% of total variance of subjective career success, which confirms practical implications for the importance of organizational variables and the legitimacy of applying the multilevel model. The significant influential factors include the degree of disability, desire for growth, self-initiating career attitude and value-oriented career attitude at the individual level and the provision of disability-related convenience, career support, personnel support, and interpersonal support at the organizational level. The latter turned out to have significant moderating effects on the influences of subjective career success on the characteristic variables at the individual level. Those findings call for plans to increase subjective career success through the activation of individual factors based on organizational effects. The study thus proposed and discussed integrated individual-corporate practice strategies including setting up a convenience support system by reflecting the disability characteristics, applying a worker support program, establishing a frontier career development support system, and providing assistance for a human network.

• Korean Journal of Agricultural and Forest Meteorology
• /
• v.25 no.2
• /
• pp.61-70
• /
• 2023

In order to select high-quality winter cereal crops with high yield and to increase self-sufficiency rate of forage, their growth, yield, and feeding value of several cereal crops cultivated in winter were investigated in the paddy field of the southern region. Four wheat cultivars and green barley headed in early and mid-April, while oat and Italian ryegrass headed in early May. Fresh forage yields of wheats, green barley, and oat were significantly higher than that of Italian ryegrass, and dry forage yields of wheats and green barley were significantly higher than those of not only Italian ryegrass but also oat. In particular, the yield of a wheat cultivar 'Cheongwoo' was the highest. Mineral contents of wheat forages, even though low, were in the range 27.8~33.7mg·g^-1 DW suitable for feeding cattle and young female cows. Crude protein content of a wheat cultivar 'Cheongwoo' was high up to 7.6%, similarly to 7.0% requiring for feeding cattle. Feeding values such as total digestible nutrients (TDN) and relative feed value (RFV) of wheats and green barley were superior to those of oat and Italian ryegrass. In addition, dry matter rates of 4 wheat cultivars and green barley were in the range 30~40%, indicating that wheat cultivars and green barley could be used for various feeding purposes such as green or dried forage, and silage. Based on these results, wheat cultivars including 'Cheongwoo' and green barley could be encouraged to be cultivated in paddy fields, as high-quality winter forage crops with high yield.

• Journal of Hospice and Palliative Care
• /
• v.9 no.2
• /
• pp.86-92
• /
• 2006

Purpose: This study was conducted to develop a measuring tool for spiritual care performance of hospice team members. The tool may be utilized for providing hospice patients with more systematic and standardized spiritual tares. Methods: The concept and questions of the tool were developed, and then its validity and reliability were tested. For the validity and reliability tests, a self-reported questionnaire comprising 33 questions with 4 point scale ($1{\sim}4$), was developed, and the data were collected from 192 hospice team members from December 2005 to February 2006. Results: Thirty three questions, drafted through literature review and professional consultation, were reviewed by 20 professionals for their validity, were revised and supplemented resulted in the final 33 questions. The questions with a correlation coefficient grater than .30 were selected: all the 33 questions were selected based on this criterion. The reliability coefficient, Cronbarh's ${\alpha}$, was 0.95. The 33 questions were analyzed for factors, and six factors were extracted: relationship formation and communication, encouragement and promotion of spiritual growth, linking with spiritual resources, preparation of death, evaluation and quality control for spiritual intervention, Intervention, and spiritual assessment for intervention. Conclusion: The tool developed in this study includes six factors and has high level of reliability. This tool Will greatly contribute to assess and improve hospice care services, providing systematic and standardized spiritual cares for terminally ill patients and their families.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.08a
• /
• pp.154-155
• /
• 2012

The promise of nano-crystalites (nc) as a technological material, for applications including display backplane, and solar cells, may ultimately depend on tailoring their behavior through doping and crystallinity. Impurities can strongly modify electronic and optical properties of bulk and nc semiconductors. Highly doped dopant also effect structural properties (both grain size, crystal fraction) of nc-Si thin film. As discussed in several literatures, P atoms or radicals have the tendency to reside on the surface of nc. The P-radical segregation on the nano-grain surfaces that called self-purification may reduce the possibility of new nucleation because of the five-coordination of P. In addition, the P doping levels of ${\sim}2{\times}10^{21}\;at/cm^3$ is the solubility limitation of P in Si; the solubility of nc thin film should be smaller. Therefore, the non-activated P tends to segregate on the grain boundaries and the surface of nc. These mechanisms could prevent new nucleation on the existing grain surface. Therefore, most researches shown that highly doped nc-thin film by using conventional PECVD deposition system tended to have low crystallinity, where the formation energy of nucleation should be higher than the nc surface in the intrinsic materials. If the deposition technology that can make highly doped and simultaneously highly crystallized nc at low temperature, it can lead processes of next generation flexible devices. Recently, we are developing a novel CVD technology with a neutral particle beam (NPB) source, named as neutral beam assisted CVD (NBaCVD), which controls the energy of incident neutral particles in the range of 1~300eV in order to enhance the atomic activation and crystalline of thin films at low temperatures. During the formation of the nc-/pm-Si thin films by the NBaCVD with various process conditions, NPB energy directly controlled by the reflector bias and effectively increased crystal fraction (~80%) by uniformly distributed nc grains with 3~10 nm size. In the case of phosphorous doped Si thin films, the doping efficiency also increased as increasing the reflector bias (i.e. increasing NPB energy). At 330V of reflector bias, activation energy of the doped nc-Si thin film reduced as low as 0.001 eV. This means dopants are fully occupied as substitutional site, even though the Si thin film has nano-sized grain structure. And activated dopant concentration is recorded as high as up to 1020 #/$cm^3$ at very low process temperature (＜ $80^{\circ}C$) process without any post annealing. Theoretical solubility for the higher dopant concentration in Si thin film for order of 1020 #/$cm^3$ can be done only high temperature process or post annealing over $650^{\circ}C$. In general, as decreasing the grain size, the dopant binding energy increases as ratio of 1 of diameter of grain and the dopant hardly be activated. The highly doped nc-Si thin film by low-temperature NBaCVD process had smaller average grain size under 10 nm (measured by GIWAXS, GISAXS and TEM analysis), but achieved very higher activation of phosphorous dopant; NB energy sufficiently transports its energy to doping and crystallization even though without supplying additional thermal energy. TEM image shows that incubation layer does not formed between nc-Si film and SiO2 under later and highly crystallized nc-Si film is constructed with uniformly distributed nano-grains in polymorphous tissues. The nucleation should be start at the first layer on the SiO2 later, but it hardly growth to be cone-shaped micro-size grains. The nc-grain evenly embedded pm-Si thin film can be formatted by competition of the nucleation and the crystal growing, which depend on the NPB energies. In the evaluation of the light soaking degradation of photoconductivity, while conventional intrinsic and n-type doped a-Si thin films appeared typical degradation of photoconductivity, all of the nc-Si thin films processed by the NBaCVD show only a few % of degradation of it. From FTIR and RAMAN spectra, the energetic hydrogen NB atoms passivate nano-grain boundaries during the NBaCVD process because of the high diffusivity and chemical potential of hydrogen atoms.

• Cartoon and Animation Studies
• /
• s.37
• /
• pp.159-195
• /
• 2014

An animation film, , is a work that declared a perfect revival of Disney. It is considered that the success was the result of its impressive theme song and characters working influentially. The main characters let audience experience empathy as well as catharsis by building the image of women making their own future without relying on men, and among the characters, Elsa is still popular even if one year has passed since its premiere in Korea. In the narrative genre, the character's degree of completion is regarded to be so important that it can even determine the work's success or failure. Accordingly, to analyze the personality structure among the major components of character rising, this study focuses on the psychodynamics of fear and desire which determines the directions of thought or behavior. Fear is the emotion attributed not to a real threat but to an ominous assumption about the future. Because fear that is originated from the memory of any deficit or suppression distorts our sound needs, escaping from fear means facing the reality. To verify the unique psychodynamics of the characters, the researcher analyzed the hierarchy of their attitudes, psychological dispositions, and psychic functions by using 'MBTI Personality Typology'. According to the results, (1) Elsa and Anna are in a conflicting relationship in terms of psychic functions. Although they are the combination that shows the highest possibility of conflict, the two sisters overcome it basically grounded on fellowship and family love. (2) Although Hans and Kristoff, too, are against each other in terms of psychic functions, the two male characters do not interact with each other in the work. (3) Hans is a person equipped with psychic functions that can complement both Elsa and Anna the most effectively, but he abuses it and turns into the most fatal opponent to them. (4) Olaf is a type of person combining Anna's attitudes with Elsa's psychological dispositions. And according to the results of analyzing the frequency of expressing fear and desire, (1) Elsa employs overwhelming fear and Anna and others characters use desire as the major drive of their behavior. (2) Fear is the underlying deficit internalized in every character and is attributed to 'the deficit of family love', and as a result, they all share the pain of 'loneliness and isolation'. It is thought that analyzing psychodynamics will help us understand the character's growth tale, that is, the narration that they distort their desire for the first motive to avoid fear and end up being ruled by it, and also, they realize the underlying reason for the distorted desire in the process of getting rid of their own fear and reach self-healing. Lastly, regarding character rising in the animation, it is expected that the directions and analysis results of this research will be referred to as a database in creating characters and setting up relations among them.

• Journal of the Korean Institute of Landscape Architecture
• /
• v.43 no.5
• /
• pp.121-131
• /
• 2015

Village-concentrated agricultural regional development projects that aim for increased profits are now being aimed at core agricultural and fishing areas. These agricultural and fishing stimulus projects aim to not only increase the net profit of local citizens but also improve their living conditions. As the industry itself has changed, local rural areas have also changed in various ways. One such aspect is the emergence of rural-urban complexes known as "rurban" areas. These naturally occurring rurban regions are created by a combination of complex urban infrastructure while maintaining the insulated rural communities that agricultural areas are usually so readily identified by. "Jeongeupsi Naejangsnagdong", the target of this research, also specifies the unaltered surrounding natural environment of rural areas while at the same time containing complex central living areas typically found in urban areas. This research suggests that the direction of residents' participation in community-level rurban projects could solve the problems found in existing top-down government development projects. This research also suggests rurban area activation plans to improve living conditions through analysis of both local rurban agricultural characteristics and citizen demands. In order to encourage citizen autonomy and self-governing attitudes, citizen-strengthening workshop programs are proposed, such as citizen workshops or pilot activities. This research was carried out by target area analysis, rudimentary planning, development direction setting, detailed project planning, and finally project processing. This procedure established three goals, which are walking environment improvement, community infrastructure establishment, and good living environment establishments, based on actual site research and citizen demands. This research suggests plans to activate community groups that were already established and reflect citizen needs as the main avenues for local businesses. This research is predicted to promote more active and successful growth through autonomy in stimulating these increasingly emerging rurban agricultural regions.

• Asia-Pacific Journal of Business Venturing and Entrepreneurship
• /
• v.8 no.2
• /
• pp.75-82
• /
• 2013

This study was carried out to contribute to the self-help and sustainability of grassroots business in Gangwon-do. To achieve this, after setting up the concept of community business, understanding the current designating status of community business and analyzing the business content and the business promotion system, I tried to analyze the continuing factors of businesses and shops, which are more than hundred years old, in Japan and seek a solution to the sustainability of community business in the province. The community business in the province, which is designated and operated, is like this; 86 preliminary social businesses, 62 town businesses, 38 social businesses. The total comes to 186. The preliminary social businesses and the social businesses are assigned more in urban area and the manufacturing sector and educational field have a lot of business contents. When it comes to the business promotion system, there are many incorporated companies and limited companies. While the town businesses are assigned more in county area, the agricultural food field and cultural world have a lot of business contents. When it comes to the main participant of business, the agricultural corporations took the first place overwhelmingly. Especially, I found out that the main participants of community business consist of 38 voluntary associations, which is 20.4 %, and we need to make up for the specialty deficiency in business management. In order to keep the continuity of community business in the province, we could achieve the results of manpower development through the case analysis research, securing good materials which can give the consumers confidence, increasing the quality of the products, maintaining high technical skills, keeping up the tradition of business and demanding forecasting. I think a successive research efforts will be required for securing good materials and increasing the quality of the products in tandem with the local community. And also we need to establish a supporting & operating system through the liaison between the business & academic world, business & administration, and business & business for securing a management specialty as an industrialist.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.65 no.3
• /
• pp.222-230
• /
• 2020

Maize grain quality can be improved by raising lysine content, which is an essential amino acid present in insufficient quantities in normal maize. Maize varieties with such modifications are known as quality protein maize (QPM). To date, no Korean maize cultivars contain high amounts of lysine. To introduce quality protein maize to Korean cultivars, we crossed QPM CIMMYT maize lines (CML) with KS140, an elite inbred line used as a parent of several cultivars such as 'Gangdaok' and 'Pyeonganok'. We analyzed the phenotypic characteristics of F₁ plants as well as the protein contents, amino acids, and fatty acids profiles of the self-pollinated seeds of the F₁ hybrids, and evaluated the feasibility of CML as a source of QPM. Days to anthesis of the CML ranged from 78 to 90 days after planting (DAP), whereas a range of 81~87 was recorded for F₁ hybrids. The average days to anthesis was 85 for KS140, CML, and the F₁ hybrids. The protein content of the CML was measured to be between 9.1 and 12.1%, with the highest and lowest values being recorded in CML153 and 191, respectively. The F₁ hybrids had protein contents of 9.1~11.1%, and the highest content was observed in KS141/CML188. The fatty acids profiles were very similar across all analyzed maize samples, and linoleic acid (C18:2) composed the greatest proportion. Glutamic acid made up the largest proportion of amino acids in all maize samples. Lysine composition was highest in CML155 (6.92% of all amino acids), with an average composition of 4.83% across the CML. In contrast, KS140 showed a lysine content of 2.51%. In F₁ hybrids, the average lysine composition was 3.46%, and KS140/CML164 (4.18%) and KS140/CML163 (4.99%) contained more lysine than either parent. Taken together, these results indicate that CML could become promising QPM sources to improve grain quality in Korean maize cultivars.