• Proceedings of the Korean Vacuum Society Conference
• /
• 2015.08a
• /
• pp.189-189
• /
• 2015

Plasmonics, sensor, field effect transistors, solar cells 등 다양한 적용분야를 가지는 실리콘 구조체는 제작공정에 의해 전기적 및 광학적 특성이 달라지기 때문에 적합한 나노구조 제작방법이 요구되고 있다. 나노구조체 제작방법으로는 Photo lithography, Extreme ultraviolet lithography (EUV), Nano imprinting lithography (NIL), Block copolymer (BCP) 방식의 방법들이 연구되고 있으며, 특히 BCP는 direct self-assembly 특성을 가지고 있으며 가격적인 면에서도 큰 장점을 가진다. 하지만 BCP를 mask로 사용하여 식각공정을 진행할 경우 BCP가 버티지 못하고 변형되어 mask로서의 역할을 하지 못한다. 이러한 문제를 해결하기 위하여 본 논문에서는 BCP와 질화막을 이용한 double mask 방법을 사용하였다. 기판 위에 BCP를 self-assembly 시키고 mask로 사용하여 hole 부분으로 노출된 기판을 Ion gun을 통해 질화 시킨 후에 BCP를 제거한다. 기판 위에 hole 모양의 질화막 표면은 BCP와 다르게 etching 공정 중 변형되지 않는다. 이러한 질화막 표면을 mask로 사용하여 pillar pattern의 실리콘 나노구조체를 제작하였다. 질화막 mask로 사용되는 template은 PS와 PMMA로 구성된 BCP를 사용하였다. 140kg/mol의 polystyrene과 65kg/mol의 PMMA를 톨루엔으로 용해시키고 실리콘 표면 위에 spin coating으로 도포하였다. Spin coat 후 230도에서 40시간 동안 열처리를 진행하여 40nm의 직경을 가진 PS-b-PMMA self-assembled hole morphology를 형성하였다. 질화막 형성 및 etching을 위한 장비로 low-energy Ion beam system을 사용하였다. Reactive Ion beam은 ICP와 3-grid system으로 구성된 Ion gun으로부터 형성된다. Ion gun에 13.56 MHz의 frequency를 갖는 200W 전력을 인가하였다. Plasma로부터 나오는 Ion은 $2{\Phi}$의 직경의 hole을 가지는 3-grid hole로 추출된다. 10~70 voltage 범위의 전위를 plasma source 바로 아래의 1st gird에 인가하고, 플럭스 조절을 위해 -150V의 전위를 2nd grid에 인가한다. 그리고 3rd grid는 접지를 시켰다. chamber내의 질화 및 식각가스 공급은 2mTorr로 유지시켰다. 그리고 기판의 온도는 냉각칠러를 이용하여 -20도로 냉각을 진행하였다. 이와 같은 공정 결과로 100 nm 이상의 높이를 갖는 40 nm직경의 균일한 Silicon pillar pattern을 형성 할 수 있었다.

• Restorative Dentistry and Endodontics
• /
• v.28 no.6
• /
• pp.491-497
• /
• 2003

The purpose of this study was to evaluate the correlation between hybrid layer thickness and bond strength using confocal laser scanning microscope and microtensile bond strength test of two adhesive systems. The dentin surface of human molars. sectioned to remove the enamel from the occlusal surface. Either Scotchbond Multi-Purpose(3M Dental Product, St. Paul, MN, U.S.A) or Clearfil SE Bond (Kuraray, Osaka, Japan) was bonded to the surface. and covered with resin-composite. The resin-bonded teeth were serially sliced perpendicular to the adhesive interface to measure the hybrid layer thickness by confocal laser scanning microscope. The specimen were trimmed to give a bonded cross-sectional surface area of $1\textrm{mm}^2$, then the micro-tensile bone test was performed at a cross head speed of 1.0 mm/min. All fractured surfaces were also observed by stereomicroscope. There was no significant differences in bond strengths the materials(p>0.05). However. the hybrid layers of three-step dentin adhesive system, SM, had significantly thicker than self-etching adhesive system. CS(p<0.05). Pearson's correlation coefficient showed no correlation between hybrid layer thickness and bond strengths(p>0.05). Bond strengths of dentin adhesive systems were not dependent on the thickness of hybrid layer.

• The Journal of Advanced Prosthodontics
• /
• v.6 no.6
• /
• pp.434-443
• /
• 2014

PURPOSE. The purpose of this study was to evaluate and compare the effects of different surface pretreatment techniques on the surface roughness and shear bond strength of a new self-adhering flowable composite resin for use with lithium disilicate-reinforced CAD/CAM ceramic material. MATERIALS AND METHODS. A total of one hundred thirty lithium disilicate CAD/CAM ceramic plates with dimensions of $6mm{\times}4mm$ and 3 mm thick were prepared. Specimens were then assigned into five groups (n=26) as follows: untreated control, coating with $30{\mu}m$ silica oxide particles ($Cojet^{TM}$ Sand), 9.6% hydrofluoric acid etching, Er:YAG laser irradiation, and grinding with a high-speed fine diamond bur. A self-adhering flowable composite resin (Vertise Flow) was applied onto the pre-treated ceramic plates using the Ultradent shear bond Teflon mold system. Surface roughness was measured by atomic force microscopy. Shear bond strength test were performed using a universal testing machine at a crosshead speed of 1 mm/min. Surface roughness data were analyzed by one-way ANOVA and the Tukey HSD tests. Shear bond strength test values were analyzed by Kruskal-Wallis and Mann-Whitney U tests at ${\alpha}=.05$. RESULTS. Hydrofluoric acid etching and grinding with high-speed fine diamond bur produced significantly higher surface roughness than the other pretreatment groups (P<.05). Hydrofluoric acid etching and silica coating yielded the highest shear bond strength values (P<.001). CONCLUSION. Self-adhering flowable composite resin used as repair composite resin exhibited very low bond strength irrespective of the surface pretreatments used.

• Proceedings of the KIEE Conference
• /
• 1993.11a
• /
• pp.261-263
• /
• 1993

The effects of the magnetic field and gas pressure on the etching characteristics were investigated in the axial magnetic field enhanced RIE system. This system has many advantages compared with the conventional RIE system ; the capability of operating at low pressure, low self-bias voltage, high electron density and high etch rate in the low pressure, but also has disadvantages such as the nonconformity of plasma density which intensifies as the magnitude of magnetic field increases. To overcome this problem we made some grooved anode and tried to find the optimal pressure and B-field strength.

• Proceedings of the KACD Conference
• /
• 2002.11a
• /
• pp.706-706
• /
• 2002

No Abstract, See Full Text

• The Journal of the Korean dental association
• /
• v.53 no.3
• /
• pp.187-194
• /
• 2015

This paper reflects on the state of the art of two kinds of tooth hard tissue (enamel and dentin) bonding with resin cement. After presenting composition of resin cement, concepts of enamel bonding and resin bonding are addressed. Special attention is devoted to the concept and advantage of self-etching technique. Finally, recommended clinical performance regarding bonding to tooth with resin cement is summarized.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.31 no.4
• /
• pp.636-644
• /
• 2004

Recently, self-etching adhesive system have been developed and bonding procedures simplified into one or two steps, which are simultaneously applied to both enamel and dentin. These systems are easy to use and have the potential for good clinical success. The purpose of this study is to evaluate in vitro the microleakage on the cementum/dentin and enamel walls in composite resin restoration of Class V cavities, regarding the use of different adhesive systems. 30 human premolars were divided into 3 groups. A standardized Class V preparation was prepared on the buccal and lingual surface of each premolar. The preparation were made parallel to the cementoenamel junctions, with the gingival half of the preparation extending 1mm apical to the cementoenamel junction. After adhesive system was applied to teeth as manufacture's recommendation, hybrid resin composite was filled in bulk into the preparation and light polymerized according to manufacturer's recommendations. Specimen were stored in distilled water at $37^{\circ}C$ for 5 days and thermocycled 1000 times ($5^{\circ}C{\pm}2^{\circ}C\;and\;55^{\circ}C{\pm}2^{\circ}C)$, then immersed in a 2% methylene blue solution for 12 hours. After sectioning mesio distally through the restorations, the degree of dye penetration was scored under a stereomicroscope at ${\times}\;25$ magnification. The data were analyzed statistically using t-test and one-way ANOVA. The results were as follows: ${\cdot}$ There is no adhesive system which can prevent microleakage perfectly. ${\cdot}$ There is significant difference in microleakage between enamel margin and dentin margin (p<0.0001). ${\cdot}$ In enamel margin, self-etching primer systems did not show any significant difference comparing total-etching system. In denin margin, self-etching primer systems did not show any significant difference comparing one-bottle adhesive system used in combination with total-etching.

• Restorative Dentistry and Endodontics
• /
• v.28 no.3
• /
• pp.203-208
• /
• 2003

The purpose of this study was to evaluate the effect of salivary contamination of teeth on bonding efficacy of self-priming and self-etching DBSs. The materials used were Single Bond(SB, self-priming system, 3M), Unifil Bond(UB, self-etching system, GC), and Scotchbond Multi-Purpose Plus(SM, 3M) as control. Forty five human molars randomly allocated to three groups as dentin bonding systems tested and embedded in epoxy resin. Then the specimens were wet-ground to expose flat buccal enamel surface or flat occlusal dentin surface and cut bucco-lingually to form two halves with slow speed diamond saw. One of them was used under non-contamination, other under contamination with saliva. The bonding procedure was according to the manufacturer's directions and resin composite(Z-100, 3M Dental Products, St. Paul, MN) was built-up on the bonded surface 5mm high. The specimens were ground carefully at the enamel-composite interface with fine finishing round diamond bur to create an hour-glass shape yielding bonded surface areas of $1.5{\pm}0.1\textrm{mm}^2$. The specimens were bonded to the modified microtensile testing apparatus with cyanoacrylate, attached to the universal testing machine and stressed in tension at a CHS of 1mm/min. The tensile force at failure was recorded and converted to a tensile stress(MPa). Mean values and standard deviations of the bond strength are listed in table. One-way ANOVA was used to determine significant difference at the 95% level. The bond strength of SBMP and SB were not affected by salivary contamination, but that of UB was significantly affected by salivary contamination. These results indicate that DBSs with total etch technique seems less likely affected by salivary contamination in bonding procedure.

• Journal of Dental Rehabilitation and Applied Science
• /
• v.18 no.4
• /
• pp.289-299
• /
• 2002

The bond strength is one of the most important factor in establishing long-term success of esthetic restorative dentistry. So, various restorative materials have been introduced to improve the esthetic and physical properties. Ormocer (organically modified ceramic) was developed as a result of such efforts. This study was performed to compare the shear bond strength of ormocer based adhesive with that of existing dentin adhesive. In this study $Admira^{(R)}$ and $Admira^{(R)}$ bond of the ormocer system are grouped together for ADM, Single $Bond^{(R)}$ which is an one-bottle adhesive and Z-250TM which is hybrid composite resin of BIS-GMA system for SIN, and $Definite^{(R)}$ of ormocer and Etch & $Prime^{(R)}$ 3.0 which is a self etching priming/ bonding agent for ETC. The results of this study were as follows. : (1) In the comparison of shear bond strength according to different adhesive system, shear bond strength was increased in the order of ETC group, SIN group, ADM group. There was no significant difference between ADM group and SIN group. However, there was a significant level of difference between ADM and ETC groups as well as SIN and ETC groups( p<0.05). (2) Examination by a scanning electron microscope showed a well established hybrid layer and resin tag in both ADM group and SIN group, while ETC group showed a minimal formation of the hybrid layer when compared with ADM and SIN groups. From the above results, it may be reasonable to start the clinical application of ormocer system, and it is recommended that ormocer system should be used along with an ormocer based adhesive because ormocer system showed the lower shear bond strength when it used with other existing self etching priming/bonding agent. The self etching priming/bonding agent showed relatively low shear bond strength, and it is considered that the further study should be needed.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.44 no.4
• /
• pp.419-426
• /
• 2017

Attachment of the orthodontic bracket conducted during the window opening procedure can result in failure due to various adverse conditions such as blood or saliva contamination, or other wet conditions. For the success of the bracket attachment, reduction of total operation time is crucial. The purpose of this literature is to evaluate the differences between the final resultant shear bond strength of the conventional method of using phosphoric acid and self-etching primer, and that of the operation time-reduced method in which the curing step is omitted subsequent to the primer application. A total of 40 human maxillary incisors were prepared. Group I(control group) and II were etched with 37% phosphoric acid and Group III and IV were conditioned with self-etching primer. Attachment of the group I and III was conducted by manufacturer's instructions. The operation time of Group II and IV was reduced by eliminating the curing step after the primer application. The resultant shear bond strength of each group was measured and an adhesive remnant index (ARI) was recorded. The mean shear bond strength of group I, II, III, and IV were 14.16 MPa, 8.33 MPa, 8.29 MPa, and 6.48 MPa respectively. Significant differences could only be found between the control group and the experimental groups (p < 0.05). The ARI indicated no significant difference among all groups.