• Journal of the Korean Ceramic Society
• /
• v.48 no.6
• /
• pp.559-564
• /
• 2011

In order to investigate the behavior of $SiO_2$ in the molybdenum silicide powders, crystal structure of these powders was measured by XRD, in addition, surface composition and surface phase (or chemical states) and microstructure were analysed by XPS and TEM, respectively. Mo-silicide powders containing $SiO_2$ were synthesized by SHS (Self-Propagating High-Temperature Synthesis) technique. In XRD result, according to increase of $SiO_2$ contents, the crystal structure for synthesized $MoSi_2$ powders was still typical $MoSi_2$ bct without any other phases. By XPS analysis, the surface of Mo and Si source powders was covered with $MoO_3$ and $SiO_2$, respectively, and the surface of synthesized $MoSi_2$ powder was also covered with $MoO_3$ and $SiO_2$, which were stable oxides at room temperature. However, according to increase of $SiO_2$ addition, $MoSi_2$ phase in XPS spectra decreased and $SiO_2$ phase increased relatively in synthesized $MoSi_2$ powders. From the results by XPS and XRD, we found that the existent $SiO_2$ has amorphous structure. In the microstructure, the small particulates of the synthesized products added $SiO_2$ agglomerated together to form larger clusters (from ~10 nm to ~1 ${\mu}m$). From TEM, XPS, and XRD results, we found that the out layer of agglomeration of synthesized $MoSi_2$ powder is surrounded by amorphous $SiO_2$.

• Korean Journal of Materials Research
• /
• v.8 no.11
• /
• pp.987-992
• /
• 1998

Titanium aluminide intermetallic compound was formed from high purity elemental Ti and A1 foils by selfpropagating, high-temperature synthesis(SHS1 in hot press. Formation of $TiAl_3$ intermetallics at the interface between Ti and Al foil was observed to be controlled by temperature, pressure and heating rate. Especially, the heating rate is the most important role to form intermetallic compound by SHS reaction. According to DTA experiment, the SHS reactions appeared at two different temperatures below and above the melting point of Al. It was also observed that both SHS reaction temperatures increased with increasing the heating rate. After the SHS reaction of alternatively layered 10 Ti and 9 A1 foils at the heating rate of $20^{\circ}C$/min, the $700\mu\textrm{m}$ thick titanium aluminide sheet was formed by heat treatment at $810^{\circ}C$ for 4hours.

• Journal of the Korean Ceramic Society
• /
• v.31 no.11
• /
• pp.1249-1258
• /
• 1994

Titanium carbide was synthesized by reacting the prepared titanium powder and carbon black using SHS method sustains the reaction spontaneously, utilizing heat generated by the exothermic reaction itself. In this process, the effect of the particle size of titanium powder on combustion temperature and combustion wave velocity was investigated. By controlling combustion temperature and combustion wave velocity via mixing Ti and C powder with TiC, the reaction kinetics of TiC formation by SHS method was considered. Without reference to the change of combustion temperature and combustion wave velocity, TiC was easily synthesized by combustion reaction. As the particle size of titanium powder was bigger, or, as the amount of added diluent(TiC) increased, combustion temperature and combustion wave velocity were found to be decreased. The formation of TiC by combustion reaction in the Ti-C system seems to occur via two different mechanisms. At the beginning of the reaction, when the combustion temperatures were higher than 2551 K, the reaction was considered to be controlled by the rate of dissolution of carbon into a titanium melt with an apparent activation energy of 148 kJ/mol. For combustion temperatures less than 2551 K, it was considered to be controlled by the atomic diffusion rate of carbon through a TiC layer with an apparent activation energy of 355 kJ/mol. The average particle size of the synthesized titanium carbide was smaller than that of the starting material(Ti).

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09b
• /
• pp.1203-1204
• /
• 2006

Cu-$TiB_2$ nanocomposite powders were synthesized by combining high-energy ball-milling of Cu-Ti-B mixtures and subsequent self-propagating high temperature synthesis (SHS). Cu-40wt.%$TiB_2$ powders were produced by SHS reaction and ball-milled. The milled SHS powder was mixed with Cu powders by ball milling to produce Cu-2.5wt.%$TiB_2$ composites. $TiB_2$ particles less than 250nm were formed in the copper matrix after SHS-reaction. The releative density, electrical conductivity and hardness of specimens sintered at $650-750^{\circ}C$ were nearly 98%, 83%IACS and 71HRB, respectively. After heat treatment at 850 to $950^{\circ}C$ for 2 hours under Ar atmosphere, hardness was descedned by 15%. Our Cu-$TiB_2$ composite showed good thermal stability at eleveated temperature.

• Journal of the Korean Ceramic Society
• /
• v.44 no.6 s.301
• /
• pp.338-342
• /
• 2007

Porous silicon nitride ceramics were prepared by SHS (Self-Propagating High Temperature Synthesis) from silicon powder, silicon nitride powder and pore-forming precursor. The microstructure, porosity and the flexural strength of the porous silicon nitride ceramics were varied according to the Si/Si3N4 ratio, size and amount of the pore-forming precursors. Some sample exhibited as high flexural strength as $162{\pm}24\;MPa$. The high strength is considered to result from the fine pore size and the strong bonding amoung the silicon nitride particles.

• Journal of the Korean Ceramic Society
• /
• v.45 no.7
• /
• pp.418-422
• /
• 2008

The preparation of FeB by SHS in $B_2O_3-Mg-Fe-Fe_3O_4$ system was investigated in this study. In the preparation of FeB, the effects of the initial pressure of inert gas in reactor, the content of Mg and $Fe_3O_4$ in mixture on the reactivity and reaction products was investigated. The minimum initial pressure of inert gas in reactor for SHS reaction in this system was 25 atm, and as the pressure increased, the concentration of unreacted Mg decreased and combustion temperature increased. At the initial inert gas pressure in reactor of 25 atm, the optimum composition for the preparation of pure FeB was $1.5B_2O_3$+3.43Mg+ 1.7Fe+$0.1Fe_3O_4$. The FeB synthesized in this condition had an irregular shape and the particle size of $5\;{\mu}m$.

• Journal of the Korean institute of surface engineering
• /
• v.50 no.3
• /
• pp.212-218
• /
• 2017

$Mg_xNi_yZn_{1-x-y}Fe_2O_4$ ferrite powders were prepared by self-propagating high temperature synthesis followed by classifying with an ultrasonic wet-magnetic separation unit to get high pure nano-sized particles. The $Mg_xNi_yZn_{1-x-y}Fe_2O_4$ ferrites were well formed by using several powders like iron, nickel oxide, zinc oxide and magnesium oxide at 0.1 MPa of oxygen pressure. The ultrasonic wet-magnetic separation of pre-mechanical milled ferrite powders resulted in producing the powders with average size of 800 nm. The addition of a surfactant during the wet-magnetic separation process improved productivity more than twice. The coercive force, maximum magnetization and residual magnetization of the $Mg_xNi_yZn_{1-x-y}Fe_2O_4$ nano-powders with 800 nm size were 3651 A/m, $53.92Am^2/kg$ and $4.0Am^2/kg$, respectively.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2016.11a
• /
• pp.201.2-201.2
• /
• 2016

$Mg_xNi_yZn_{1-x-y}Fe_2O_4$ ferrite powders were prepared by self-propagating high temperature synthesis followed by classified by ultrasonic wet-magnetic separation method to get nano-sized particles with high purity. The $Mg_xNi_yZn_{1-x-y}Fe_2O_4$ ferrites were well formed by using several powders like iron, nickel oxide, zinc oxide and magnesium oxide at 0.1 MPa of oxygen pressure. The ultrasonic wet-magnetic separation of pre-mechanical milled ferrite powders produced the powders with average size of $3.7-0.8{\mu}m$. The addition of a surfactant during the separation process improved productivity more than twice. The coercive force, maximum magnetization and residual magnetization of the $Mg_xNi_yZn_{1-x-y}Fe_2O_4$ nano-powders with 810 nm size were 45.89 Oe, 53.92 emu/gOe, 0.4 emu/Oe, respectively.

• Resources Recycling
• /
• v.6 no.4
• /
• pp.31-37
• /
• 1997

The Mg-ferrite powders were recovered from acid leaching Mg waste by hydrothermal method. Recovering conditions ofMg-Ferrite were investigated m this system and the powders prepared were characterized, using X-ray analysis, chemicalanalysis, SEM. TEM, and VSM. In this study, pH of solution and the kind of neutralizer wcre important factors on thecharacteristics of the product. The optimum condition of recovering MgPenite was the mole ratio of Fe" : Mg"=2'1, reactiontemperature : ZOWC, reaction time.lhr, at pH=lZ, and Oi partial pressure af 2000 psi. And the powders ~ccovered have amonodispersed and spherelike shapes with the narrow sue distribulion.ow sue distribulion.

• Journal of Powder Materials
• /
• v.6 no.3
• /
• pp.215-223
• /
• 1999

The synthesis of $Ni_5Si_2,\;Ni_2Si$ and NiSi has been investigated by mechanical alloying (MA) of Ni-27.9at%Si, Ni-33.3at%Si and Ni-50.0at%Si powder mixtures. As-received and premilled elemental powders were subjected to MA. The as-received Ni powder was spherical and the mean particle size 48.8$\mu$m, whereas the premilled Ni powder was flaky and the mean particle diameter and thickness were found to be 125 and 5$\mu$m, respectively. The mean surface area of the premilled Mi powder particle was 3.5 times as large as that of the as-received Ni powder particle. The as-received Si powder was was 10.0$\mu$m. Self-propagating high-temperature synthesis (SHS) reaction, followed by a slow reaction (a solid state diffusion), was observed to produce each Ni silicide during MA of the as-received elemental powders. In other word , the reactants and product coexisted for a long period of MA of time. Only SHS reaction was, however, observed to produce each Ni silicide during MA of the premilled elemental powders, indicating that each Ni sillicide formed rather abruptly at a short period of MA time. The mechanisms and reaction rates for the formation of the Ni silicides appeared to be influenced by the elemental powder particle size and shape as well as the heat of formation of the products $(Ni_5Si_2$longrightarrow-43.1kJ/mol.at., $Ni_2Si$$\rightarrow$-47.6kJ/mol.at.).