• Journal of the Korean earth science society
• /
• v.32 no.6
• /
• pp.674-686
• /
• 2011

Choosing a seismic source and geophone type including a coupling method can be the most important factor in shallow seismic surveys. We studied the characteristics of seismic signals by analyzing 6 different seismic data sets that collected from several sources and geophone conditions. Geophones attached to weight plate (1.8 kg) can be easily and economically installed on the paved road where geophones with spikes would cause the coupling problem. In addition, experiments in this study revealed that a small handy hammer can be used as a seismic source by striking the paved road to generate the seismic signals within 200 ms two-way travel time. Attaching weight plates to geophones may change the geophone response curve which generally depends on the geophone mass, but the change seems not to give significant differences in the first arrival of refracted wave and in the pattern of reflection events. Consequently, using weight plates on paved roads can be an efficient and cost-saving method in the near-surface high-resolution seismic surveys.

• Geophysics and Geophysical Exploration
• /
• v.6 no.2
• /
• pp.95-100
• /
• 2003

In this study, we developed reflection tomography inversion algorithm using Straight Ray Technique (SRT) which can calculate travel time easily and fast for complex geological structure. The inversion process begins by setting the initial velocity model as a constant velocity model that hat only impedance boundaries. The inversion process searches a layer-interface structure model that is able to explain the given data satisfactorily by inverting to minimize data misfit. For getting optimal solution, we used Gauss-Newton method that needed constructing the approximate Hessian matrix. We also applied the Marquart-Levenberg regularization method to this inversion process to prevent solution diverging. The ability of the method to resolve typical target structures was tested in a synthetic salt dome inversion. Using the inverted velocity model, we obtained the migration image close to that of the true velocity model.

• Geophysics and Geophysical Exploration
• /
• v.20 no.3
• /
• pp.163-175
• /
• 2017

In land seismic exploration, irregular surface topography and weathering layer in near surface distorts the reflected signals of data. Therefore, typical land seismic data should be compensated for this distortion by static correction. To perform the static correction, near-surface velocity is required, which can be obtained by seismic refraction survey. However, land seismic data is often acquired in a limited form of geometry depending on the equipment availability, accessibility condition, and permission for the survey site. In this situation, refraction analysis should be performed using reflection data because it is impossible to acquire refraction-oriented data due to limited source and receiver geometry. In this study, we aimed to analyze the reliability of the results obtained by refraction traveltime tomography when using reflection data with a limited number of sources and receivers from irregular surface topography. By comparing the inversion result from irregular topography with that from flat surface, we found that the surface topography affects the reliability of the inversion results to some degree. We also found that the number of sources has little effect on the inversion results unless the number of sources are very small. On the other hand, we observed that velocity distortion occurred in the overlapped part of receiver arrays when using a limited number of receivers, and therefore suggested the size of the least overlapping ratio to avoid the velocity distortion. Finally, we performed numerical tests for the model which simulates the surface topography and acquisition geometry of the survey region and verified the reliability analysis of inversion results. We identified reliable areas and suspicious area of the inverted velocity model by applying the analysis results to field data.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2001.03a
• /
• pp.167-174
• /
• 2001

Reflection method using ultrasonic source has been attempted to obtain the information about tunnel lining structures composed of lining, shotcrete, water barrier and voids at the back of lining. In this work, two different types of sources, i.e. single-pulse source and sweep source, can be used. Single-pulse source with short time duration has the frequency content whose amplitudes tend to be concentrated around the dominant frequency, whereas sweep source with long time duration denotes a flat distribution of relatively larger amplitude over a broad frequency band, although the peak to peak amplitude of single-pulse source wavelet is equivalent to that of sweep source one. In traditional seismic application, a single-pulse source(weight drop, dynamite) is typically used. However, to investigate the fine structure, as it is the case in the tunnel lining structure, the sweep wavelet can be also a desirable source waveform primarily due to the higher energy over a broad frequency band. For the investigation purposes of sweep source, a physical modeling is a useful tool, especially to study problems of wave propagation in the fine layered media. The main purpose of this work was using a physical modeling technique to explore the applicability of sweep source to the delineation of inner layer boundaries. To this end, a two-dimensional physical model analogous to the lining structure was built and a special ultrasonic sweep source was devised. The measurements were carried out in the sweep frequency range 10 ∼ 60 KHz, as peformed in the regular reflection survey(e.g. roll-along technique). The measured data were further rearranged with a proper software (cross-correlation). The resulting seismograms(raw data) showed quitely similar features to those from a single-pulse source, in which high frequency content of reflection events could be considerably emphasized, as expected. The data were further processed by using a regular data processing system "FOCUS" and the results(stack section) were well associated with the known model structure. In this context, it is worthy to note that in view of measuring condition the sweep source would be applied to benefit the penetration of high frequency energy into the media and to enhance the resolution of reflection events.

• 한국지구물리탐사학회:학술대회논문집
• /
• 2006.06a
• /
• pp.95-100
• /
• 2006

To reveal subsurface structures of the Ulsan fault, seismic data were recorded along a 750-m long line near Nongso-Eup in Ulsan. P and S waves were generated simultaneously by impacting a 5 kg sledgehammer on a tilted plate. The data were received by 16 10-Hz 3-component geophones at 3 m intervals. Refracted P waves were inverted using the tomography method. Dip moveout and migration were applied to reflection data processed following a general sequence. Four layers were identified based on P-wave velocities and P- and S-wave stacked image. From top to bottom, the P-wave velocity of each layer ranges in $300{\sim}1100\;m/s$, $1100{\sim}1700\;m/s$, $1700{\sim}2700\;m/s$, and greater than 2700 m/s. The corresponding thickness of the top three layers averages 3.9 m, 5.9 m, 4.4 m, respectively. The S-wave stack section is effective to define subsurface structures shallower than 10 m.

• Economic and Environmental Geology
• /
• v.23 no.3
• /
• pp.353-358
• /
• 1990

This paper presents numerical experiments on migration of synthetic seismograms using by $45^{\circ}$ wave equation. The seismograms used are zero-offset seismogram (corresponding to stacked section) on point reflectors, dipping plane reflector, faulted and folded layers. The seismograms are constructed by upward continuation of seismic source wavelets, exploading on subsurface reflection interfaces, to the earth surface. The synthetic seismograms are migrated by downward continuation and imaging. The upward and downward continuations are implemented by solving the $45^{\circ}$ wave equation with the finite-difference method. Migration of the synthetic data used in this study results in relatively accurate reposition of subsurface structures while the synthetic sections are quite different from the structures.

• Economic and Environmental Geology
• /
• v.29 no.5
• /
• pp.629-637
• /
• 1996

In this paper a numerical experiment is conducted to determine the low acoustic impedance of a thin oil or gas reservoir from a seismogram by using the generalized linear inversion method. The seismograms used are normal incident synthetic seismograms containing p-wave primary reflections, multiples, and peg-leg multiples on the layers consisting of oil-, gas-, water-filled sandstone incased in shales. In this experiment the acoustic impedance, the location of reservoir boundary, thickness, and source wavelet are assumed initially and revised iteratively by the least-squares-error technique until the difference between the seismogram and calculated one is very small. This experiment shows that the acoustic impedance and thickness, about 10 m thick, can be determined by the inversion.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2001.03a
• /
• pp.245-248
• /
• 2001

During the core drilling for the design of a railway bridge crossing over the inferred fault system along the river, fracture zone, extends vertically more than the bottom of borehole, filled with fault gouge was found. The safety of bridge could be threatened by the excessive subsidence or the reduced bearing capacity of bedrock, if a fault would be developed under or around the pier foundation. Thus, a close examination of the fault was required to rearrange pier locations away from the fault or to select a reinforcement method if necessary. Geophysical methods, seismic reflection method and electrical resistivity survey over the water covered area, were applied to delineate the weak zone associated with the fault system. The results of geophysical survey clearly showed a number of faults extending vertically more than 50m. Reinforcement was not desirable because of the high cost and the water contamination, etc. The pier locations were thus rearranged based on the results of geophysical surveys to avoid the undesirable situations, and additional core drillings on the rearranged pier locations were carried out. The bedrock conditions at the additional drilling sites turned out to be acceptable for the construction of piers.

• Geophysics and Geophysical Exploration
• /
• v.19 no.2
• /
• pp.76-83
• /
• 2016

Migration image can be distorted due to reflected waves in the source and receiver wavefields when discontinuities of input velocity model exist in seismic imaging. To remove reflected waves coming from layer interfaces, it is a common practice to smooth the velocity model for migration. If the velocity model is smoothed, however, the subsurface image can be distorted because the velocity changes around interfaces. In this paper, we attempt to minimize the distortion by reducing reflection energy in the source and receiver wavefields through acoustic impedance homogenization. To make acoustic impedance constant, we define fake density model and use it for migration. When the acoustic impedance is constant over all layers, the reflection coefficient at normal incidence becomes zero and the minimized reflection energy results in the improvement of migration result. To verify our algorithm, we implement the reverse-time migration using cell-based finite-difference method. Through numerical examples, we can note that the migration image is improved at the layer interfaces with high velocity contrast, and it shows the marked improvement particularly in the shallow part.

• Geophysics and Geophysical Exploration
• /
• v.2 no.1
• /
• pp.1-7
• /
• 1999

We investigated the weathering characteristics of On-Yang gneiss by means of geological survey and Ground Penetrating Radar(GPR). The results of geological survey and boring show the two sets of vertical joint and horizontal joint developed by foliation which is composed of salic and melanic layers. GPR section evidently shows foliation direction and differential weathering due to discontinuity and mineral composition of metamorphic rock. The GPR section for instantaneous phase attribute based on complex trace analysis evidently shows continuity and foliation direction of metamorphic rock. The strong reflection amplitude which is derived from the banded structure of weathered rock can be incorrectly interpreted as a reflection of bedrock. The depth of rock basement should be estimated from the overall exploration result such as boring, seismic method, and electrical resistivity method.