• Journal of the Korea Concrete Institute
• /
• v.25 no.3
• /
• pp.339-345
• /
• 2013

This study is to derive from the required performances and the optimum mix proportion of the roof concrete placed in the in-ground LNG storage tank with a capacity of 200000 $m^3$, and propose the actual data for site concrete work. The concrete placing work without sliding and segregation in the fresh concrete condition is very important because the slope of domed roof is varied in the large range by its curvature. Also the control of hydration heat and the strength development at test ages are classified with massive section about 1.4 m thick and considered to the pre-stressing work and removal of air support after concrete placing work. Considering above condition, slump range is selected $100{\pm}25$ mm under the slope $20^{\circ}$ and $150{\pm}25$ mm over the slope $20^{\circ}$ s until 60 minutes of elapsed time. Also, the roof concrete is satisfied with compressive strength range including design strength at 91 days (30 MPa), pre-stressing work at 7 days (10 MPa), air support removal work at 21 days (14 MPa). Replacement ratio of limestone powder is determined by confined water ratio test and main design factors include water-cement ratio (W/C), sand-aggregate ratio and dosage of admixture. As test results, the optimum mix proportion of the roof concrete used low heat cement is as followings. 1) Replacement ratio of limestone powder 25% by confined water ratio test 2) Water-cement ratio 57.8% 3) Sand-aggregate ratio 42.0%. Also, test results for the adiabatic temperature rising test is satisfied with its criteria and shown the lower value compared to preceding storage tank (TK-13, 14). These required performances and the optimum mix proportion is to apply the actual construction work.

• Journal of Mushroom
• /
• v.13 no.3
• /
• pp.217-222
• /
• 2015

This study was conducted to obtain a growth correlation of basal information from the development of disease resistant Flammulina velutipes cultivars through back-crossing between the strains of wild-type brown monokaryon 4019-20 and the derivative of commercial quality white monokaryons 3. The two strains were selected to back-cross for further enhancing their latent attributes and growth characteristics. The parents of 4019-$20{\times}M3$ back-crossed to reproduce $F_1$, M3-Sn. Using $F_1$, M3-Sn procured and isolated into 94 monokaryon strains. Further examination of growth characteristics carried out by back-crossing between M3 and $BC_1F_1$ from M3-n dikaryon. Monokaryon exhibited an irregular growth pattern and demonstrated to be sluggish development in the sawdust medium. However $BC_1F_1$(M3-n) dikaryon strains confirmed mostly regular growth pattern and demonstrated ordinary growth in the sawdust medium. The fruitbody of $BC_1F_1$ confirmed as light-brown colour to be the dominant gene. The colour distributions of fruitbody, $BC_1F_1$, resulted as follows; 7% of dark brown, 25% of brown, 27% of light brown, 16% of ivory and 25% of white. The ratio of the other color to white showed 3 to 1 which suggested two major genes were related to fruitbody color.

• Journal of Life Science
• /
• v.28 no.4
• /
• pp.398-407
• /
• 2018

The Purple pericarp (Prp) trait is a trait often bred for in black rice. Generally, the Prp trait is displayed in the color variations of seeds following the 9:3:4 purple, brown, and white ratio, respectively. The Prp trait is a recessive epistasis of two gene interactions; however, it is caused by the two complementation genes Pb and Pp. Here we present a study of the genetic characteristics of the Prp trait using an $F_1$ hybrid with a Pbpb Pppp genotype. This hybrid generated four seed colors with the following numbers: 3 dark purple, 6 medium purple, 3 brown, and 4 white (or 9 purple, 3 brown, and 4 white). However, further biochemical analysis of the all progenies divided them into two groups. One group had the Pb_ Pp_ allelic constitutions and contained cyanidin 3-O-glucoside (C3G) in both the dark purple or medium purple seeds. The other group, however, was absent of C3G in both the brown and white seeds, resulting in a ratio of 9:7, respectively. This segregation revealed the extended Mendelian 9:7 ratios of the complementary gene interactions with a good fitness in ${\chi}^2$ analysis. Further analysis revealed that brown seeds with the Pb_ pppp genotype corresponded with a null C3G, indicating that the Brown pericarp trait in rice is caused by a dominant allele of the Pb gene. Therefore, we conclude that the production of C3G is a main phenotype of the black and purple colored rice in the Prp trait, and it is governed by the complementary gene interactions between Pb and Pp genes.

• Journal of the Microelectronics and Packaging Society
• /
• v.10 no.3
• /
• pp.19-27
• /
• 2003

Surface finishes of PCB laminates are important in the solder joint reliability of flip chip package because the types and thicknesses of intermetallic compound(IMC), and compositions and hardness of solders are affected by them. In this study, effects of surface finishes of PCB on the low cycle fatigue resistance of Sn-based lead-free solders; Sn-3.5Ag, Sn-3.5Ag-XCu(X=0.75, 1.5), Sn-3.5Ag-XBi(X=2.5, 7.5) and Sn-0.7Cu were investigated for the Cu and Au/Ni surface finish treatments. Displacement controlled room temperature lap shear fatigue tests showed that fatigue resistance of Sn-3.5Ag-XCu(X=0.75, 1.5), Sn-3.5Ag and Sn-0.7Cu alloys were more or less the same each other but much better than that of Bi containing alloys regardless of the surface finish layer used. In general, solder joints on the Au/Ni finish showed better fatigue resistance than those on the Cu finish. Cross-sectional fractography revealed microcracks nucleation inside of the interfacial IMC near the solder mask edge, more frequently on the Cu than the Au/Ni surface finish. Macro cracks followed the solder/IMC interface in the Bi containing alloys, while they propagated in the solder matrix in other alloys. It was ascribed to the Bi segregation at the solder/IMC interface and the solid solution hardening effect of Bi in the $\beta-Sn$ matrix.

• Journal of Mushroom
• /
• v.2 no.3
• /
• pp.115-126
• /
• 2004

Somatic hybrids of inter-compatible and inter-incompatible strains were obtained by protoplast fusion. The fusion products between compatible strains, Pleurotus ostreatus and P. florida, formed heterokaryons, while fusants between incompatible strains such as P. cornucopiae + P. florida, P. ostreatus + Ganoderma applanatum, P. florida + Ganoderma lucidum, and P. ostreatus + Flammulina velutipes formed synkaryons that retained genes from both parents. The heterokaryons showed the same level of basidioma development. In contrast, the synkaryons showed unique characteristics including clamp connection formation at mitosis, either partner basidioma development, and abnormal segregation and recombination compared with inter-compatible strains. Synkaryons can be classified into homokaryoyic and heterokaryotic type. A comparison of somatic hybrids with compatible and incompatible strains was made using random amplified polymorphic DNA (RAPD) analysis. The heterokaryons between compatible species showed the same level of variability and contained both parental RAPD bands. In contrast, most of the synkaryons between incompatible species showed similarity to those of either parental bands and non-parental RAPD bands. Synkaryons can be classified into microgenome insertion type and macrogenome insertion type. A tetrapolar mating system was found among monospore isolates in somatic hybrids and wild type P. ostreatus. Homokaryons from each somatic hybrid combination were paired with tester homokaryons of the initial wild type of P. ostreatus. The changed mating types were identified in progenies. The pattern of mating type switching in somatic hybrids depends on compatibility of fusion partner. There are several factors related to the mechanism of clamp connection formation and fruiting body development of synkaryons. Of these,the major factor may be associated with self-fertility and mating type switching such as homokaryotic fruiting of wild type P. ostreatus. This review will discuss these aspects.

• Korean Chemical Engineering Research
• /
• v.54 no.4
• /
• pp.533-542
• /
• 2016

We investigate fluidization characteristics of the mixture of rice husk, silica sand and rice husk ash as a preliminary study for valuable utilization of rice husk ash obtained from gasification of rice husk in a fluidized bed reactor. As experiment valuables, the blending ratio of rice husk and sand (rice husk: sand) is selected as 5:95, 10:90, 20:80 and 30:70 on a volume base. Rice husk ash was added with 6 vol% of rice husk for each experiment and air velocity to the reactor was 0~0.63 m/s. In both rice husk/sand and rice husk/sand/ash mixture, the minimum fluidization velocity (Umf) is observed as 0.19~0.21 m/s at feeding of 0~10 vol.% of rice husk and 0.30 m/s at feeding of 20 vol.% of rice husk. With increasing the amount of rice husk up to 30 vol.%, $U_{mf}$ can not measure due to segregation behavior. The mixing index for each experiment is determined using mixing index equation proposed by Brereton and Grace. The mixing index of the mixture of rice husk/sand and rice husk/sand/ash was 0.8~1 and 0.88~1, respectively. The optimum fluidization condition was found for the good mixing and separation of rice husk ash.

• Journal of Conservation Science
• /
• v.25 no.2
• /
• pp.207-217
• /
• 2009

After replicating 10 bronze types such as Gyemija, Gyeongjaja, Eulhaeja, etc. before the Imjin war, we studied the change of microstructure from each casting process, method, and alloy ratio by Gyechukja replicated from "Donggukyeojiseungnam". We selected the average of compositions of Eulhaeja in the National Museum of Korea as the standard(Cu 86.7%, Sn: 9.7%, Pb: 2.3%) of bronze types, so we decided on the alloy's composition of Cu 87%, Sn 15%, Pb 8% added to 5% Sn and Pb contents because of evaporating the Sn and the Pb. Before replicating major metal types, we made master-alloy first, melting it again, and then replicated metal types. The composition of the 1'st replicated Gyechukja showed the range of Cu 85.81~87.63%, Sn 9.27~10.51%, Pb 3.05~3.19%. The 2'nd replicated Gyechukja made using the branch metal left after casting the 1st replica. The 2nd replicated Gyechukja showed the composition range of Cu 87.21~88.09%, Sn 9.06~9.36%, Pb 2.80~3.05%. This result decreases a little contents of Sn and Pb as compared with metal types of the 1st replica. However, it's almost the same as the Eulhaeja's average composition ratio in the National Museum of Korea. As a result of observing the microstructure of restored Gyechukja, it showed the dendrite structure of the typical casting structure and the segregation of Pb. There is no big difference of microstructure between the 1st and the 2nd restored metal types, even though the 2nd restored types partially decreases the eutectoid region in comparison with the 1st types. The systematic and scientific restoration experiment of metal types using Joseon period will be showed the casting method and alloy ratio, and this will be of great help to the study of restoration metal types in the future.

• Journal of Korean Society of Environmental Engineers
• /
• v.30 no.3
• /
• pp.302-313
• /
• 2008

The purposes of this study are to investigate the concentration levels of fine particles, so called PM$_{2.5}$, to identify the affecting sources, and to estimate quantitatively the source contributions of PM$_{2.5}$. Ambient air sampling was seasonally carried out at two sites in Pohang(a residential and an industrial area) during the period of March to December 2003. PM$_{2.5}$ samples were collected by high volume air samplers with a PM$_{10}$ Inlet and an impactor for particle size segregation, and then determined by gravimetric method. The chemical species associated with PM$_{2.5}$ were analyzed by inductively coupled plasma spectrophotometery(ICP) and ion chromatography(IC). The results showed that the most significant season for PM$_{2.5}$ mass concentrations appeared to be spring, followed by winter, fall, and summer. The annual mean concentrations of PM$_{2.5}$ were 36.6 $\mu$g/m$^3$ in the industrial and 30.6 $\mu$g/m$^3$ in the residential area, respectively. The major components associated with PM$_{2.5}$ were the secondary aerosols such as nitrates and sulfates, which were respectively 4.2 and 8.6 $\mu$g/m$^3$ in the industrial area and 3.7 and 6.9 $\mu$g/m$^3$ in the residential area. The concentrations of chemical component in relation to natural emission sources such as Al, Ca, Mg, K were generally higher at both sampling sites than other sources. However, the concentrations of Fe, Mn, Cr in the industrial area were higher than those in the residential area. Based on the principal component analysis and stepwise multiple linear regression analysis for both areas, it was found that soil/road dust and secondary aerosols are the most significant factors affecting the variations of PM$_{2.5}$ in the ambient air of Pohang. The source apportionments of PM$_{2.5}$ were conducted by chemical mass balance(CMB) modeling. The contributions of PM$_{2.5}$ emission sources were estimated using the CMB8.0 receptor model, resulting that soil/road dust was the major contributor to PM$_{2.5}$, followed by secondary aerosols, vehicle emissions, marine aerosols, metallurgy industry. Finally, the application and its limitations of chemical mass balance modeling for PM$_{2.5}$ was discussed.

• Journal of Plant Biotechnology
• /
• v.33 no.4
• /
• pp.309-313
• /
• 2006

Discovery of single nucleotide polymorphisms (SNPs), including small insertions and deletions, is one of the hot topics in genetic research. The most common type of sequence variant consists of single base differences or small insertions and deletions at specific nucleotide positions. Significance of SNPs in rice is increasing for genetic research, positional cloning and molecular breeding. $F_2$ 170 lines and $F_3$ 194 lines derived from Sangjuchalbyeo/HR13721-53-3-1-3-3-2-2 Were used for Searching SNP markers related to bacterial blight resistance. Sangjuchalbyeo is susceptible to bacterial blight, but HR13721-53-3-1-3-3-2-2 has Xa1 gene resistant to bacterial blight. Individual lines were inoculated with $K_1$ race of bacterial blight and resistant or susceptible was evaluated after 3 weeks from inoculation. The genotypes of population were analysed by PCR-RFLP for SNP marker developing. The segregation of $F_2\;and\;F_3$ population showed almost 3:1, 1:1 ratio, respectively. Analysis of genotype using SNP marker is capable of confirming resistance for $K_1$ race and genotype through amplifying the gene using 16PFXal primer and digested the PCR product with Eco RV. There were close relation between resistance test for $K_1$ race and SNP marker genotype. Especially, DNA analysis using SNP marker is capable of judging homozygote/heterozygote in $F_2$ population compared with resistant test for Kl race. So, it seems to improve the selection efficiency in disease resistant breeding.

• Journal of Life Science
• /
• v.15 no.2 s.69
• /
• pp.253-260
• /
• 2005

Mitotic centromere-associated kinesin (MCAK), which is a member of the Kin I (internal motor domain) subfamily of kinesin-related proteins, is known to play a role in mitotic segregation of chromosome during M phase of the cell cycle. In the present study, we have produced a rat polyclonal antibody using human MCAK (HsMCAK) expressed in E. coli as the antigen. The antibody specifically recognized the HsMCAK protein (81 kDa), and could detect its nuclear localization in human Jurkat T cells and 293T cells by Western blot analysis. The specific stage of the cell cycle was obtained through blocking by either hydroxyl urea or nocodazole and subsequent releasing from each blocking for 2, 4, and 7 h. While the protein level of HsMCAK reached a maximum level in the S phase with slight decline in the $G_{2}-M$ phase, the electrophoretic mobility shift from $p81^{MCAK}\;to\;p84^{MCAK}$ began to be induced in the late S phase and reached a maximum level in the $G_{2}/M $ phase, and then it disappeared as the cells enter into the $G_{1}$ phase. Immunocytochemical analysis revealed that HsMCAK protein localized to centrosome and nucleus at the interphase, whereas it appeared to localize to the spindle pole, centromere of the condensed mitotic DNA, spindle fiber, or midbody, depending on the specific stage of the M phase. These results demonstrate that a rat polyclonal antibody raised against recombinant HsMCAK expressed in E. coli specifically detects human MCAK, and indicate that the electrophoretic mobility shift from $p81^{MCAK}\;to\;p84^{MCAK}$, which may be associated with its differential intracellular localization during the cell cycle, fluctuates with a maximum level of the shift at the $G_{2}-M$ phase.