• Journal of Korean Tunnelling and Underground Space Association
• /
• v.23 no.2
• /
• pp.93-106
• /
• 2021

In general, segment lining tunnel refers to a tunnel formed by connecting precast concrete segments as a ring and connecting such rings to each other in the longitudinal direction of the tunnel. As the structural properties of the segment lining is highly dependent on the behavior of the segment joints, thus correct modelling of joint behavior is crucial to understand and design the segment tunnel lining. When the tunnel is subjected to ground loads, the segment joint behaves like a hinge that resists rotation, and when the induced moment exceeds a certain limit of the rotation then it may enter into non-linear field. In understanding the effect of the segment joint on the lining behavior, a moment-rotation relationship of the segment joint was explored based on the Japanese practice and Janssen's approach commonly used in the actual design. This study also presents a method to determine the rotational stiffness of joint refer to the bearing strength. The rotation of the segment joint was estimated in virtual design conditions based on the existing models and the proposed method. And the sectional force of the segment lining and joint were calculated along with the estimated rotation. As the rotation at the segment joint increases, the joint contact area decreases, so the designer have to verify the segment joint for bearing strength as well. This paper suggests a consistent method to determine the rotational stiffness and bearing strength of joints.

• Proceedings of the KIEE Conference
• /
• 2004.11c
• /
• pp.129-131
• /
• 2004

Elliptic Curve Cryptography (ECC) coprocessors support massive scalar multiplications of a point. We research the design for multi-segment multipliers in fixed-size ECC coprocessors using the multi-segment Karatsuba algorithm on GF($2^m$). ECC coprocessors of the proposed multiplier is verified on the SoC-design verification kit which embeds ALTERA EXCALIBUR FPGAs. As a result of our experiment, the multi-segment Karatsuba multiplier, which has more efficient performance about twice times than the traditional multi-segment multiplier, can be implemented as adding few H/W resources. Therefore the multi-segment Karatsuba multiplier which satisfies performance for the cryptographic algorithm, is adequate for a low cost embedded system, and is implemented in the minimum area.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.59 no.6
• /
• pp.1143-1149
• /
• 2010

In this study, we propose a novel method to detect and enhance the feature of ST-segment which offers the crucial information for the diagnosis of myocardial infarction and ischemia. With this aim, PQRST features of Electrocardiogram initially are detected and subsequently ST-segment are estimated. And Dynamic Time Warping(DTW) transformation is applied recursively to minimize the difference in time between ST-segments and calculate the minimum cumulative distance that decides the degree of similarity among ST-segments. As of the results, the inherent characteristic of ST-segment can be emphasized in terms of time parameter and thus the diagnostic features of a ST-segment can be revealed further.

• Journal of the Korean Society for Aviation and Aeronautics
• /
• v.22 no.2
• /
• pp.9-15
• /
• 2014

'Visual segment surface' means a surface that extends from the missed approach point of non precision approaches (or the decision altitude location for approaches with vertical guidance and precision approaches) to the threshold to facilitate the identification of and protection from obstacles in this visual segment of the approach. Validation is the necessary final quality assurance step in the procedure design process, prior to publication. The purpose of validation is the verification of all obstacle and navigation data, and assessment of flyability of the procedure. This paper shows how to apply the protection for the visual segment of the approach procedure, and the results of the validation for visual segment surface conducted at an airport.

• Speech Sciences
• /
• v.11 no.4
• /
• pp.207-221
• /
• 2004

There are two different approaches in studying mapping between syntactic structure and prosody, the 'phonetic approach' and the 'phonological approach'. An experiment to examine which approach is more valid was conducted. In the experiment, syntactically ambiguous Seoul Korean sentences in each of which a noun immediately after an adjective starts with either an H-segment (a segment which triggers the AP-initial H tone) or an L-segment (a segment other than H-segments) were recorded. by 3 Seoul Korean speakers. The F0 values in the syllables containing the consonants in question were then measured. The results show that interaction between the segment type and the branching structure is statistically significant. which suggests that it is difficult to use the phonetic .approach to generalize the relationship between syntax and prosody. Thus, it is concluded that the phonological approach is more valid.

• Phonetics and Speech Sciences
• /
• v.2 no.4
• /
• pp.59-65
• /
• 2010

In this paper, we investigate acoustic characteristics of Korean /s/ when it is followed by both a high front and a round segment regardless of their order to one another. We show that Korean /s/ in this environment has characteristics of a labio-palatalized segment, being affected by both a high front and a round segment if they occur within the domain of a syllable. In the experiment, we show that Korean /s/ before a high front and a round segment shows a spectral shape different from that in other environments. Specifically, it is different from /s/ before a high front segment only, showing peaks around 2.5 kHz. Furthermore, it shows a rapid decrease of amplitude in 4-5 kHz, and sometimes another plateau of high peaks in 5-6 kHz. We also examined center of gravity frequency and band energy difference. Based on the results of this experiment, we argue that Korean /s/ is affected by the following segments within the domain of coarticulation, a syllable and that the degree of coarticulation is different from language to language.

• Macromolecular Research
• /
• v.10 no.6
• /
• pp.365-368
• /
• 2002

Thermoplastic polyurethanes (TPUs) with different hard segment length has been prepared from a fixed molar ratio of poly(tetramethylene ether glycol), 4,4'-diphenylmethane diisocyanate, and 1,4-butanediol by different polymerization procedures. Results reveal that the on-set temperature of endotherms ( $T_{cc}$ ) due to the crystallization of hard segments by cooling the TPUs from melt and the peak temperature of endotherms due to the melting of hard segments ( $T_{mh}$ ) by heating the TPUs increased and levelled off with increasing the hard segment length of TPUs. It has also been observed that soft segment glass transition temperature ( $T_{gs}$ ) of TPU decreased slightly with increasing the hard segment length, which explains less mixing of soft segments and hard segments. In tensile measurement of TPUs, strain hardening is observed with increasing the hard segment length, which is attributed to the strain induced crystallization of soft segments.

• Journal of the Semiconductor & Display Technology
• /
• v.19 no.4
• /
• pp.130-134
• /
• 2020

This paper proposes a new method for the digit recognition on a 7-segment display. The proposed method uses morphological processing that dilates segments of digits and connects them into strokes. The digits are extracted by connected component analysis and finally, template matching method recognizes the extracted digits. The proposed method is implemented using C language in Raspberry Pi 4 system with a camera module for a real-time image processing. Experiments were conducted by using various 7-segment LED displays and 7-segment mono LCD displays. The results show that the proposed method is successful for the digit recognition on the 7-segment displays.

• Animal Systematics, Evolution and Diversity
• /
• v.22 no.1
• /
• pp.1-11
• /
• 2006

Three new species of Kelleria are described based on the females from the invertebrate burrows in the Port Seogwipo, Jeju Island, Korea. These species possess in common no process on the inner margin of the free segment of leg 5. Kelleria grandisetiger n. sp. possesses a large seta on lateral sides of the genital double-somite and a small thumb-like process near base of the free segment of leg 5. Kelleria undecidentata n. sp. possesses the elongated free segment of leg 5 which is more than four times as long as wide and 11 teeth on the distal margin of the second maxillary segment. Kelleria portiviva n. sp. possesses one seta and one distinct spine on the distal margin of the free segment of leg 5, ten or 11 teeth on the distal margin of the second maxillary segment, and a tuft of spinules on the convex outer comer of mandible.

• Maxillofacial Plastic and Reconstructive Surgery
• /
• v.16 no.1
• /
• pp.51-62
• /
• 1994

The sagittal split osteotomy of the mandibular ramus is a common procedure which has been used in the correction of mandibular deformities for a few decades. Although the technical improvements have increased the reliability and stability of SSRO procedure, the postoperative relapse is imperative and clinically more significant than any other complication. One of the major causes of the relapse is due to the displacement of the proximal segment during SSRO procedure, which is well documented in the literature. Therefore it is important to preserve the original position of the proximal segment during SSRO proced and maxillofacial fixation period. In the case of mandibular asymmetry, if one side of mandible is advanced and the other side of mandible is setback during SSRO procedure, the proximal segment in the advancement site will rotate laterally and the proximal segment in the setback site will rotate medially. For the prevention of the lateral rotation or flaring of the proximal segment in the advancment site. we deliberately fracture the posterior protion of the distal segment in green-stick fashion during SSRO procedure, and there is no need to fix the fractured lingual segment. We fix the two osteotomized bony segments in the buccal cortex area rigidly with adjustable monocortical plates and screws. During SSRO procedure the lingual fracture technique was applied to nine patients with severe mandibular asymmetry who underwent orthognathic surgery in our hospital since march, 1992. These clinical experiencies enable us to find the lingual fracture technique has the following advantages. 1. The proximal segment is displaced minimally. 2. The osteotomized bony segments are contacted intimately. 3. The postoperative relapse and the healing period are decreased.