• Journal of the Society of Naval Architects of Korea
• /
• v.45 no.6
• /
• pp.611-619
• /
• 2008

In most shipyards Floating Dock-gate System is adapted for dry docks. For the safe launching of ships in dry docks, smooth operation of dock-gate must be guaranteed. So it is very important to grasp its behavior in waves for securing the high productivity and the safety of workers. Its seakeeping ability was estimated numerically at the floating conditions and the free roll decay and the seakeeping model tests of dock-gate was carried out with bilge-keels of 3 different widths which have a scale of 1 to 20. More than 20% decrease of roll motion was observed in irregular beam seas by applying a bilge-keel system to the dock-gate that is long and narrow.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.3 no.1
• /
• pp.9-19
• /
• 2011

The paper describes the validation of two time domain methods to simulate the behaviour of a destroyer operating in steep, stern-quartering seas. The significance of deck-edge immersion and water on deck on the capsize risk is shown as well as the necessity to account for the wave disturbances caused by the ship. A method is described to reconstruct experimental wave trains and finally two deterministic validation cases are shown.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2013.06a
• /
• pp.15-16
• /
• 2013

This paper is mainly concerned with the ship-bank interaction by model test. The experiments for the characteristics of hydrodynamic interaction forces and moments between vessel and bank with a mound were carried out in the seakeeping and maneuvering basin.

• Proceedings of the Korea Committee for Ocean Resources and Engineering Conference
• /
• 2004.05a
• /
• pp.36-41
• /
• 2004

STX Shipbuilding Company is under construction design the marine training ship if Korea Maritime University. Processing q this training ship development, model test results and design if general arrangement results are introduced in this paper.

• Journal of Navigation and Port Research
• /
• v.37 no.3
• /
• pp.251-256
• /
• 2013

This paper is mainly concerned with the ship-bank interaction by model test. The experiments for the characteristics of hydrodynamic interaction forces and moments between vessel and bank with a mound were carried out in the seakeeping and maneuvering basin. A series of tests were carried out with ship model in parallel course along a vertical sidewall with a mound with varying lateral spacing between model ship and sidewall, length of sidewall and water depth. From the experimental results, it indicated that the hydrodynamic interaction effects increase as length of sidewall with a mound increases. Furthermore, for lateral spacing less than about 0.2L between vessel and bank, it can be concluded that the bank effects increase largely as the lateral spacing between vessel and bank decreases. However, for spacing between vessel and bank more than about 0.3L, the interaction effects increase slowly as lateral spacing decreases. Also, for the water depth to draft ratio(h/d) less than about 1.5, the hydrodynamic interaction effects increase dramatically as h/d decreases.

• Journal of the Society of Naval Architects of Korea
• /
• v.29 no.1
• /
• pp.71-80
• /
• 1992

The Seakeeping committee of Korea Towing Tank Conference executed the cooperative experimental study on deck wetting phenomena using S-175 contatiner model ships. Two members, Korea Research Institute of Ships and Ocean Engineering(KRISO) and Hyundai Maritime Research Institute(HMRI) participated in the study. This study was initiated by the ITTC(International Towing Tank Conference) Seakeeping Committee as the cooperative study of the 19th ITTC aiming at the establishement of the model test procedure on the deck wetting phenomena. Special emphasis was made on the determination of reliable record length for experimental measurement on rarely occurring events(such as deck wetness, slamming etc). Comparisons were made on both the test results and the test procedrues in this research. The measured frequencies of deck wetting show remarkable deviations between the runs. This fart implies that sufficiently long record length is required in the deck wetness measurement compared to the conventional ship motion tests. Careful considerations were made on the physical interpretation of the deck wetting phenomena, the correlation between the measured relative motion at stemhead and the measured deck wetness, and the estimation of deck wetting frequencies by Poisson process.

• Journal of Navigation and Port Research
• /
• v.44 no.5
• /
• pp.363-374
• /
• 2020

In the past, various research on the effects of waves generated by ships has been investigated. The most noticeable effect of the waves generated by a passing ship is the increase of the hydrodynamic forces and the unwanted large motion of the moored ship and high mooring forces that occur. Thus, it is crucial to investigate the effect of the waves generated by the passing ship near port on the motion of the moored ship and the tension of the mooring lines. A model test was performed with virtual ship-generated waves in a square tank at CWNU (Changwon National University). The IMU (Inertial Measurement Unit) and Optical-based system were used to measure the 6DOF (Six Degrees of Freedom) motion of the moored floater. Additionally the tension of mooring lines were measured by the tension gauges. The effects of the wave direction and wave height generated by the virtual ship-generated waves on the motion of the moored floater were analyzed.

• Journal of the Society of Naval Architects of Korea
• /
• v.55 no.5
• /
• pp.431-437
• /
• 2018

The running attitude of a planing hull is determined by the pressure distribution on the hull bottom, and it significantly affects hydrodynamic performance of the ship, i.e., resistance, maneuverability, and seakeeping ability. Therefore, it is essential to investigate pressure distribution on the hull bottom in order to improve hull design. In the present study, a novel pressure measurement system using tactile sensors was introduced for a planing hull. The test model was a 23 m-class planing hull with a hard chine. The pressure measurement showed that the pressure at the transom was lower than the atmospheric pressure, owing to flow separation at the transom.

• Journal of the Society of Naval Architects of Korea
• /
• v.55 no.2
• /
• pp.103-115
• /
• 2018

This paper performs a numerical computation of ship maneuvering performance in waves. For this purpose, modular-type model (MMG (Mathematical Modeling Group) model) is adopted for maneuvering simulation and wave drift force is included in the equation of maneuvering motion. In order to compute wave drift force, two different seakeeping programs are used: AdFLOW based on Wave Green function method and SWAN based on Rankine panel method. When wave drift force is calculated using SWAN program, not only ship forward speed but also ship lateral speed are considered. By doing this, effects of lateral speed on wave drift force and maneuvering performance in waves are confirmed. The developed method is validated by comparing turning test results in regular waves with existing experimental data. Sensitivities of wave drift force on maneuvering performance are, also, checked.

• Journal of Ocean Engineering and Technology
• /
• v.35 no.6
• /
• pp.446-456
• /
• 2021

To build an environment facility of a large-scale ocean basin, various detailed reviews are required, but it is difficult to find data that introduces the related research or construction processes on the environment facility. The current generator facility for offshore structure safety evaluation tests should be implemented by rotating the water of the basin. However, when the water in the large basin rotates, relatively large flow irregularities may occur and the uniformity may not be adequate. In this paper, design and review were conducted to satisfy the performance goals of the DOEB through computational numerical analysis on the shape of the waterway and the flow straightening devices to form the current in the large tank. Based on this, the head loss, which decreases the flow rate when the large tank water rotates through the water channel, was estimated and used as the pump capacity (impeller) design data. The impeller of the DOEB current generator was designed through computational numerical analysis (CFD) based on the lift surface theory from the axial-type impeller shape for satisfying the head loss of the waterway and maximum current velocity. In order to confirm the performance of the designed impeller system, the flow rate and flow velocity performance were checked through factory test operation. And, after installing DOEB, the current flow rate and velocity performance were reviewed compare with the original design target values. Finally, by measuring the current velocity of the test area in DOEB formed through the current generator, the spatial current distribution characteristics in the test area were analyzed. Through the analysis of the current distribution characteristics of the DOEB test area, it was confirmed that the realization of the maximum current velocity and the average flow velocity distribution, the main performance goals in the waterway design process, were satisfied.