• Journal of the Society of Naval Architects of Korea
• /
• v.43 no.1 s.145
• /
• pp.50-58
• /
• 2006

Free running model tests gives us only maneuvering indices not hydrodynamic derivatives. For this reason, system identification method has been applied to the measured data to identify mathematical model describing hydrodynamic force. However It is difficult to obtain complete set of maneuvering derivatives because of strong correlation of sway velocity and yaw rate. Therefore, in this paper, we assumed that sway velocity related coefficients would be obtained by oblique towing test. and then proposed new procedure to estimate yaw related coefficients. To do this, correlation and regression analyses were carried out to establish modified model and estimate maneuvering derivatives. Also D-optimal rudder input scenario was found based on the modified model and confirmed the validity of its sufficient richness as a input scenario.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.56 no.2
• /
• pp.172-182
• /
• 2020

In order to offer specific information needed to assist in operation of a ship with same type rudder through evaluating the maneuverability of training ship A-Ra with flapped rudder, sea trials based full scale for turning test, zig-zag test with rudder angle 10° and 20°, and spiral test at service condition were carried out on starboard and port sides around Jeju Island according to the standards of maneuverability of IMO. As a result, the angular velocity of port turn was higher than that of starboard turn. Therefore, the size of turning circle was longer on the starboard side. In addition, variation of the transfer due to various factors was more stable than those of the others. In the Z-test results, the mean of 1st and 2nd overshoot angles were 9.8°, 6.3° and 15.3°, 9.2° respectively when the port and starboard was 10°; the 1st overshoot angle were 18°, 13.7° when using 20°. Her maneuverability index T' and K' can be easily determined by using a computer with the data obtained from Z-test where K' and T' are dimensionless constants representing turning ability and responsiveness to the helm, respectively. In the Z-test under flap rudder angle 10°, the obtained K' value covered the range of 2.37-2.87 and T' was 1.74-3.45. Under the flap rudder angle 20°, K' and T' value showed 1.43-1.63, 1.0-1.73, respectively. In the spiral test, the loop width was unstable at +0.3° and -0.5°-0.9° around the midship of flap rudder. As a result, course stability was comparatively good. From the sea trial results, training ship ARA met the present criterion in the standards of maneuverability of IMO.

• Journal of the Society of Cosmetic Scientists of Korea
• /
• v.49 no.4
• /
• pp.349-354
• /
• 2023

Sunscreen is a product that protects against ultraviolet rays by blocking and scattering ultraviolet rays, and has now become a daily necessity beyond cosmetics. Applying sunscreen is a common and easy way to prevent skin damage caused by ultraviolet rays. Due to its significance, the evaluation of sunscreen has evolved since its regulation by the FDA in 1978, progressing to standardized methods established by ISO. Additionally, to assess the loss of sunscreen due to activities such as water exposure or sweating, the Ministry of Food and Drug Safety in Korea and ISO have established protocols for evaluating the water-resistant sun protection factor (SPF). However, existing evaluations of water resistance have been mainly confined to test methods involving plain water, and methods accounting for the impact of seawater during activities like beach leisure, sports, and recreation are yet to be established. Based on the existing guidelines for testing the water-resistant UV protection index, this study compared the water-resistant UV protection index in water, artificial seawater (salt water) and natural seawater (sea water) to evaluate the UV protection index in real-world situations such as marine leisure, sports, and leisure activities. Through these results, we were able to compare the differences between water resistance sun protection index tests in ordinary water, artificial seawater, and natural seawater, and suggest a method for water resistance sun protection index tests using natural seawater.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.18 no.2
• /
• pp.146-153
• /
• 2015

An unmanned aerial photography method by using an unmanned helicopter is useful method for measuring of the water-entry traces of small falling objects into the sea. Pixel sizes on the aerial photograph may be too large due to a limit of camcorder resolution and a wide shooting area. If the pixel size is too large, identification of water-entry trace is impossible. Thus an accurate prediction of water-entry trace size is required. The traces of water-entry could be classified into three types such as splash, water column, and bubble. Diameters of each trace are predicted by water-entry impact pressure theories, cavity theories, and trial test results. The results are verified by drop tests using an unmanned helicopter at two water-entry speeds. As a result, prediction and test results showed sufficient similarity to evaluate the identifiability of water-entry trace.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.13 no.4
• /
• pp.569-576
• /
• 2010

Jamming simulator has developed for the purpose of the test and evaluation on the electronic protection capabilities of the tracking radar onboard ship. This simulator has the capabilities to generate and radiate the jamming signals against the radar as well as those to receive, analyze and identify the radar signals at a real sea environment. The limited space of ship superstructure has led to the serious distortion caused by the ring around phenomenon that some sidelobes of the jamming beams were coming back to the receiving antenna. In this paper, we have proposed the methods to eliminate the ring around. First, we have inserted the groove metal screen between transmitting and receiving antennas. Second, we have used the PRI(Pulse Repetition Interval) tracking loop to control the switching timing of the input radar and the output jamming signal. Finally, we have demonstrated the performance and effectiveness of the proposed methods through the sea trial.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.20 no.2
• /
• pp.197-205
• /
• 2017

During the sea trial, we discovered EMI between MOSCOS and ES DF antenna. CW emitted by MOSCOS raised the threshold level of ES DF antenna. As a result, direction finding rate of ES has been decreased. This is a study for the improvement of EMI between the antennas mounted on a surface ship. An analysis is accomplished for MOSCOS, ES DF antenna and Jamming transmitter. This paper presents the method how to solve EMI based on the measurements and calculations about the ES DF antenna receiving level, MOSCOS radiation pattern and Jamming transmitter thermal noise. The test was performed with optimal deployment of MOSCOS on a surface ship. After changing the position of MOSCOS, EMI has been decreased significantly.

• Journal of the Society of Naval Architects of Korea
• /
• v.58 no.4
• /
• pp.253-261
• /
• 2021

This paper describes the process of evaluating maneuverability in still water of an unmanned surface vehicle based on data measured by performing sea trials. First, we set up a test scenario that is easy to analyze the maneuverability of the unmanned surface vehicle and to identify and verify the dynamics model. Since the attitude of hull varies according to the speed of the unmanned surface vehicle which has a planing hull shape, the relationship between waterjet RPM, speed and attitude is analyzed by performing straight forward tests at various speeds. The turning tests of the unmanned surface vehicle in which the waterjet angle rotates while turning are performed by changing the waterjet rotation angle under the condition of two representative speeds to analyze turning ability. The turning ability of the unmanned surface vehicle includes speed reduction, yaw rate, heel, and turing diameter at steady turning phase according to the speed and RPM.

• Journal of Ocean Engineering and Technology
• /
• v.21 no.6
• /
• pp.101-106
• /
• 2007

In this paper, the authors demonstrate a new idea to take the place of the real pressure vessel test, which should be carried out in a high pressure experiment unit before the real sea trial test. The idea is to make a pressure vessel model as a replica of the real pressure vessel test, which can reduce the cost of making a pressure vessel and large pressure experiment unit. The pressure vessel model was designedbased on linear-elastic, buckling equations and Finite Element Analysis. The manufactured pressure vessel model was investigated and monitored while the pressure test was being conducted. After the test, the result and the validity of the pressure vessel model as a replica of the real pressure vessel test was studied.

• Journal of the Society of Naval Architects of Korea
• /
• v.49 no.4
• /
• pp.327-332
• /
• 2012

International Towing Tank Conference (ITTC) recommended verifying a ship's ability to move transversely at zero forward speed without altering heading by a crabbing test. In sea trial, all available propellers/rudders/thrusters should be used to find the maximum possible transverse speed. For estimating crabbing ability in the design stage, tests to estimate possible swaying force and yawing moment range using all available propellers/rudders/thrusters are conducted. By butterfly diagram, which compares possible swaying force and yawing moment range with external swaying force and yawing moment by wind, a ship's crabbing ability can be estimated. In this study, model tests of a cruise vessel equipped with bow thrusters and POD system were conducted to find out her crabbing ability in the design stage. To mimic quay condition, a model quay-wall was set in the towing tank.

• Journal of Advanced Marine Engineering and Technology
• /
• v.38 no.2
• /
• pp.123-132
• /
• 2014

The maritime sector is advancing with dedicated endeavor to reduce greenhouse gas in addressing issues with regards to global warming. Since 01 January 2013, the International Maritime Organization (IMO) regulation mandatory requirement for Energy Efficiency Design Index (EEDI) has been in place and should be satisfied by newly-built ships of more than 400 gross tonnage and the Ship Energy Efficiency Management Plan (SEEMP) for all ships type. Therefore, compliance to this necessitates planning during the design stage whereas verification can be carried-out through an acceptable method during sea trial. The MEPC-approved 2013 guidance, ISO 15016 and ISO 19019 on EEDI serves the purpose for calculation and verification of attained EEDI value. Individual ships EEDI value should be lower than the required value set by these regulations. The key factors for EEDI verification are power and speed assessment and their synchronization. The shaft power can be measured by telemeter system using strain gage during sea trial. However, calibration of shaft power onboard condition is complicated. Hence, it relies only on proficient technology that operates within the permitted ISO allowance. On the other hand, the ship speed can be measured and calibrated by differential ground positioning system (DGPS). An actual test on a newly-built vessel was carried out to assess the correlation of power and speed. The Energy-efficiency Design Index or Operational Indicator Monitoring System (EDiMS) software developed by the Dynamics Laboratory-Mokpo Maritime University (DL-MMU) and Green Marine Equipment RIS Center (GMERC) of Mokpo Maritime University was utilized for this investigation. In addition, the software can continuously monitor air emission and is a useful tool for inventory and ship energy management plan. This paper introduces the synchronization and identification method between shaft power and ship speed for EEDI verification in accordance with the ISO guidance.