• 한국농공학회논문집
• /
• 제55권3호
• /
• pp.113-121
• /
• 2013

Recently, it has been studied for the application of nano-materials in the concrete. Applied a small amount of nano-materials can achieve the goal of high strength, high performance and high durability. The small addition of nano clay improves strength, thermal stability, and durability of concrete because of the excellent dispersion. The present study has investigated the effectiveness, when varying with the contents of nano clay, influencing the pull-out behavior of macro synthetic fibers in nano materials cement mortar. Pullout tests conducted in accordance with the Japan Concrete Institute (JCI) SF-8 standard for fiber-reinforced concrete test methods were used to evaluate the pullout performance of the different nano clay. Nano clay was added to the 0, 1, 2, 3, 4 and 5 % of cement weight. The experimental results demonstrated that the addition of nano clay led to improve the pull-out properties as of the load-displacement curve in the precracked and debonded zone. Also, the compressive strength, flexural strength and pullout performance and of Mix No. 1 and No. 2 increased up to the point when nano clay used increased by 2 and 3 % contents, respectively, but decreased when the exceeded 3 and 4 %, respectively. It was proved by verifying increase of the scratching phenomenon in macro synthetic fiber surface through the microstructure analysis on the surface of macro synthetic fiber.

• Tribology and Lubricants
• /
• 제11권5호
• /
• pp.128-135
• /
• 1995

Atomic force microscopy/friction force microscopy (AFM/FFM) techniques are increasingly used for tribological studies of engineering surfaces at scales, ranging from atomic and molecular to microscales. These techniques have been used to study surface roughness, adhesion, friction, scratching/wear, indentation, detection of material transfer, and boundary lubrication and for nanofabrication/nanomachining purposes. Micro/nanotribological studies of single-crystal silicon, natural diamond, magnetic media (magnetic tapes and disks) and magnetic heads have been conducted. Commonly measured roughness parameters are found to be scale dependent, requiring the need of scale-independent fractal parameters to characterize surface roughness. Measurements of atomic-scale friction of a freshly-cleaved highly-oriented pyrolytic graphite exhibited the same periodicity as that of corresponding topography. However, the peaks in friction and those in corresponding topography were displaced relative to each other. Variations in atomic-scale friction and the observed displacement has been explained by the variations in interatomic forces in the normal and lateral directions. Local variation in microscale friction is found to correspond to the local slope suggesting that a ratchet mechanism is responsible for this variation. Directionality in the friction is observed on both micro- and macro scales which results from the surface preparation and anisotropy in surface roughness. Microscale friction is generally found to be smaller than the macrofriction as there is less ploughing contribution in microscale measurements. Microscale friction is load dependent and friction values increase with an increase in the normal load approaching to the macrofriction at contact stresses higher than the hardness of the softer material. Wear rate for single-crystal silicon is approximately constant for various loads and test durations. However, for magnetic disks with a multilayered thin-film structure, the wear of the diamond like carbon overcoat is catastrophic. Breakdown of thin films can be detected with AFM. Evolution of the wear has also been studied using AFM. Wear is found to be initiated at nono scratches. AFM has been modified to obtain load-displacement curves and for nanoindentation hardness measurements with depth of indentation as low as 1 mm. Scratching and indentation on nanoscales are the powerful ways to screen for adhesion and resistance to deformation of ultrathin fdms. Detection of material transfer on a nanoscale is possible with AFM. Boundary lubrication studies and measurement of lubricant-film thichness with a lateral resolution on a nanoscale have been conducted using AFM. Self-assembled monolyers and chemically-bonded lubricant films with a mobile fraction are superior in wear resistance. Finally, AFM has also shown to be useful for nanofabrication/nanomachining. Friction and wear on micro-and nanoscales have been found to be generally smaller compared to that at macroscales. Therefore, micro/nanotribological studies may help def'me the regimes for ultra-low friction and near zero wear.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2005년도 춘계학술대회 논문집
• /
• pp.1507-1510
• /
• 2005

This study was carried out as a part of the research on the development of a maskless and electroless process for fabricating metal micro/nanostructures by using a nanoindenter and an electroless deposition technique. $2-\mu{m}-deep$ indentation tests on Ni and Cu samples were performed. The elastic recovery of the Ni and Cu was 9.30% and 9.53% of the maximum penetration depth, respectively. The hardness and the elastic modulus were 1.56 GPa and 120 GPa for Ni and 1.49 GPa and 100 GPa for Cu. The effect of single-point diamond machining conditions such as the Berkovich tip orientation (0, 45, and $90^{\circ}$) and the normal load (0.1, 0.3, 0.5, 1, 3, and 5 mN), on both the deformation behavior and the morphology of cutting traces (such as width and depth) was investigated by constant-load scratch tests. The tip orientation had a significant influence on the coefficient of friction, which varied from 0.52-0.66 for Ni and from 0.46-0.61 for Cu. The crisscross-pattern sample showed that the tip orientation strongly affects the surface quality of the machined area during scratching. A selective deposition of Cu at the pit-like defect on a p-type Si(111) surface was also investigated. Preferential deposition of the Cu occurred at the surface defect sites of silicon wafers, indicating that those defect sites act as active sites for the deposition reaction. The shape of the Cu-deposited area was almost the same as that of the residual stress field.

• Archives of Pharmacal Research
• /
• 제28권2호
• /
• pp.209-215
• /
• 2005

The antinociceptive effect of nicotine administered intracereboventricularly (i.c.v.) or intrathecally (i.t) in several pain models was examined in the present study. We found that i.t. treatment with nicotine (from 5 to 20 g) dose-dependently blocked pain behavior revealed during the second phase, but not during the first phase in the formalin test. In addition, i.c.v. treatment with nicotine (from 0.1 to $10\;{\mu}g$) dose-dependently attenuated pain behavior revealed during both the first and second phases. In addition to the formalin test, nicotine administered i.c.v. or i.t. attenuated acetic acid-induced writhing response. Furthermore, i.c.v. or i.t. administration of nicotine did not cause licking, scratching and biting responses induced by substance P, glutamate, TNF-${\alpha}$(100 pg), IL-$1{\beta}$(100 pg) and INF-${\gamma}$ (100 pg) injectied i.t. The antinociception induced by supraspinally-administered nicotine appears to be more effective than that resulting from spinally administered nicotine. Our results suggest that nicotine administration induces antinociception by acting on the central nervous system and has differing antinociceptive profiles according to the various pain models.

• 한국정밀공학회지
• /
• 제23권8호
• /
• pp.171-177
• /
• 2006

This study was performed as a part of the research on the development of a maskless and electroless process for fabricating metal micro/nanostructures by using a nanoindenter and an electroless deposition technique. $2-{\mu}m$-deep indentation tests on Ni and Cu samples were performed. The elastic recovery of the Ni and Cu was 9.30% and 9.53% of the maximum penetration depth, respectively. The hardness and the elastic modulus were 1.56 GPa and 120 GPa for Ni and 1.51 GPa and 104 GPa for Cu. The effect of single-point diamond machining conditions such as the Berkovich tip orientation (0, 45, and $90^{\circ}$ ) and the normal load (0.1, 0.3, 0.5, 1, 3, and 5 mN), on both the deformation behavior and the morphology of cutting traces (such as width and depth) was investigated by constant-load scratch tests. The tip orientation had a significant influence on the coefficient of friction, which varied from 0.52-0.66 for Ni and from 0.46- 0.61 for Cu. The crisscross-pattern sample showed that the tip orientation strongly affects the surface quality of the machined are a during scratching. A selective deposition of Cu at the pit-like defect on a p-type Si(111) surface was also investigated. Preferential deposition of the Cu occurred at the surface defect sites of silicon wafers, indicating that those defect sites act as active sites for the deposition reaction. The shape of the Cu-deposited area was almost the same as that of the residual stress field.

• 공업화학
• /
• 제21권6호
• /
• pp.670-675
• /
• 2010

나노실리카볼 입자를 합성하고 표면에 비닐기를 부여하는 합성 연구를 통해 다양한 크기로 조절이 된 유-무기하이브리드 입자인 비닐-나노실리카볼이 합성되었다. 다양한 크기의 비닐-나노실리카볼 입자를 상업적으로 적용되고 있는 아크릴-멜라민 클리어코트에 후첨시키고 경화시켰을 때, 클리어코트의 광택도 증가 및 유지 특성에 대해 연구하였다. 실리카볼 입자가 250 nm 정도인 경우 Matting effect에 의한 광택도 감소가 관측되었으나 20~30 nm로 작아지면 광택도 유지 효과가 약 7%까지 증가하였다. 나노실리카볼 대신 상업용 친수 실리카 Aerosil 200 (Hydrophilic fumed silica, 평균입도 12 nm, Degussa)을 사용하여 비닐- fumed 실리카 화합물을 합성하여 클리어코트에 적용하면 광택도 유지 효과가 약 2% 정도만 증가하였다.

• Corrosion Science and Technology
• /
• 제3권4호
• /
• pp.131-139
• /
• 2004

Effects of PbO on the repassivation kinetics and characteristics of passive film of Alloy 690 were examined to elucidate the influences of PbO on the SCC resistance of that alloy. The repassivation kinetics of the alloy was analyzed in terms of the current density flowing from the scratch, i(t), as a function of the charge density that has flowed from the scratch, q(t). Repassivation on the scratched surface of the alloy occurred in two kinetically different processes; passive film initially nucleated and grew according to the place exchange model in which log i(t) is linearly proportional to q(t), and then grew according to the high field ion conduction model in which log i(t) is linearly proportional to 1/q(t) with a slope of cBV. The cBV is found to be a parameter representing repassivation rate and hence SCC susceptibility of the alloy. The lower the value of cBV, the faster the repassivation rate and the higher the SCC resistance of an alloy. Addition of PbO to pH 4 and 10 solutions increased the value of cBV of alloy 690, reflecting slower repassivation rate than without PbO. The change in the value of cBV was grater in pH 10 than in pH 4. The increase in SCC susceptibility of alloy 690 with the addition of PbO to solution was presumably due to the Cr-depletion in the outer parts of passive film of the alloy with an incorporation of Pb compounds in the film, which was revealed by Mott-Schottky, AES and XPS analyses.

• 한국주조공학회지
• /
• 제20권2호
• /
• pp.104-109
• /
• 2000

Three different white cast irons alloyed with Cr, V, Mo and W were prepared in order to study their abrasion wear behavior in as-cast and heat-treated conditions. The specimens were produced using a 15㎏-capacity high frequency induction furnace. Melts were super-heated to $1600^{\circ}C$, and poured at $1550^{\circ}C$ into Y-block pepset molds. Three combinations of the alloying elements were selected so as to obtain the different types of carbides : 3%C-10%Cr-5%Mo-5%W(alloy No. 1: $M_7C_3$ and $M_6C$), 3%C -10%V-5%Mo-5%W(alloy No. 2: MC and $M_2C$) and 3%C-17%Cr-3%V(alloy No. 3: $M_7C_3$ only). A scratching type abrasion test was carried out in the states of as-cast(AS), homogenizing(AH), air-hardening(AHF) and tempering(AHFT). First of all, the as-cast specimens were homogenized at $950^{\circ}C$ for 5h under the vacuum atmosphere. Then, they were austenitized at $1050^{\circ}C$ for 2h and followed by air-hardening in air. The air-hardened specimens were tempered at $300^{\circ}C$ for 3h. 1 ㎏ load was applied in order to contact the specimen with abrading wheel which was wound by 120 mesh SiC paper. The wear loss of the test piece(dimension: $50{\times}50{\times}5$ mm) was measured after one cycle of wear test and this procedure was repeated up to 8 cycles. In all the specimens, the abrasion wear loss was found to decrease in the order of AH, AS, AHFT and AHF states. Abrasion wear loss was lowest in the alloy No.2 and highest in the alloy No.1 except for the as-cast and homogenized condition in which the alloy No.3 showed the highest abrasion wear loss. The lowest abrasion wear loss of the alloy No.2 could be attributed to the fact that it contained primary and eutectic MC carbides, and eutectic $M_2C$ carbide with extremely high hardness. The matrix of each specimen was fully pearlitic in the as-cast state but it was transformed to martensite, tempered martensite and austenite depending upon the type of heat-treatment. From these results, it becomes clear that MC carbide is a significant phase to improve the abrasion wear resistance.

• 대한약학회:학술대회논문집
• /
• 대한약학회 2000년도 춘계총회 및 학술대회
• /
• pp.70-81
• /
• 2000

DA-5018 is a synthetic capsaicin derivative under development as a non-narcotic a analgesic ag$\varepsilon$nt. DA-50 18 showed a potent analgesic activity against acute and chronic pain m model(Tablel, 2.), but it had a narrow margin of safety. DA-5018 did not bind to opioid(${\kappa}, {\delta}, {\mu}$), NKl, CGRP receptors in vitro and its analgesic effect was not antagonized by naloxone, a and it did not develop analgesic tolerance. In addition DA-5018 had no inhibitory effects against c cyclooxygenase and 5-lipooxygenase activities. DA-5018 significantly increased the relcase of substance P from the slices of the rat spinal cord. These results suggest that DA-50 18 is not a narcotic nor aspirin-like analgesic and the release of substance P is one of analgesic mechanism of action of DA-5018. We found that DA-5018 was almost ten times more potent and was at l least IOO-times less irritable compared to capsaicin. Accordingly development of topical formula was adopted. Topical formula was desiged and screened by flux test of DA-5018 using hairless mouse skin and several formulas were selected. With these topical formulas we a assessed the analgesic efficacy and carried out the toxicity, skin irritation and pharmacokinetic studies. In streptozotocin-induced hyperalgesic rat and 50 % galactose-fed hyperalgesic rat as diabetic pain models, DA-5018 cream increased the pain thresh이ds up to 77.0% and 24.4% respectively, while Zostrix-HP(capsaicin cream) incr$\varepsilon$as cd by 65.9% and 21.0%. DA-5018 c cream showed a good analgesic effect as welI in FCA-induced arthritic rat. DA-5018 cream did not show any toxicological signs in acute and chronic toxicity test and had little skin irritation in car swclIing and scratching t$\varepsilon$st. Pharmacokinetics of DA-50 18 were studied after topical application of ${14}^C$-Iabelled or unlabelIed DA-5018 cream. Plasma and skin concentrations c except applied skin wcre below the dctection limit and after 7-day cummulative application, plasma concentrations were also below detection limit DA-50 18 may have an advantag$\varepsilon$ ov$\varepsilon$r c capsaicin and is now being developed as a topical agent for the treatment of pains. DA-50 18 cream was approved for Korean IND and is now under a Phase II clinical study for arthritic pain a after finising Phase I study. DA-50 18 was also liscensed out to Stiefel Company in America in

• International Journal of Oral Biology
• /
• 제38권4호
• /
• pp.135-140
• /
• 2013

이상의 실험 결과들을 요약하면, 포르말린을 측두하악관절 내로 주입하여 발생한 염증성 통증 행위반응은 QX-314의 투여로 감소할 수 있었다. 저농도의 QX-314의 진통작용은 TRPV1 통로를 이용하여 세포막 내로 이동하여 작용이 나타났으며 고농도의 QX-314는 TRPV1 통로와 무관하게 진통작용을 나타내었다. 이와 같은 결과는 측두하악관절 장애로 인해 발생되는 염증성 통증에 QX-314가 효과적인 치료제로 사용할 수 있다는 것을 말해주며, 특히 고농도의 QX-314가 세포막을 이동하는 경로에 대한 연구가 더 진행된다면 임상에서 QX-314가 진통제로서 사용할 수 있는 계기가 될 것으로 판단된다.