• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2005년도 춘계학술대회 논문집
• /
• pp.1660-1663
• /
• 2005

Unwanted vibrations are inevitably induced in other directions when pure unidirectional vibration motion is desired for the vertical scratching mechanism. Pure vertical vibration motion of the scratching machine can be obtained by driving identical two motors with symmetrically positioned eccentric unbalance masses. The desired optimal condition for driving pure vertical vibration for the scratching machine is assumed to be the resonance condition in that direction. Imposing the flexibility of the scratching machine in the horizontal direction, we can find out the amount of horizontal vibration component while maintaining the resonance in vertical direction. The desired stiffness in horizontal direction which produces the minimum vibration in horizontal direction are defined which can be used as a guide line to design the supporting structure of the scratching machine.

• 한국기계가공학회지
• /
• 제3권2호
• /
• pp.53-59
• /
• 2004

In this paper, we propose a new multi-purpose Scanning Force Microscope (SFM) system. The system can be used for nano/micro-scratching, in-process profile measurement, and observation of potential surface defects which occur during the scratching in air or liquid. Experimental results of nano/micro-scratching show that the smallest scratching depth can be controlled to be 10nm, which corresponds to the stability of the SFM system. Profile measurements of nano/micro-scratching surfaces have also been performed by the method of on-machine measurement and in-process measurement. Two measurement results were in good agreement with each other. The maximum difference was approximately 10 nm, which was mainly caused by the sampling repeatability error that influences the measurement accuracy Also, micro-defects on the micro-scratching surface were successfully detected by the SFM system. It was confirmed that the number of micro-defects increases when the surface is subjected to a cyclic bending load. The maximum depth was less than 100nm.

• 한국기계가공학회지
• /
• 제2권1호
• /
• pp.75-84
• /
• 2003

In this paper, a new nano/micro-mechanical processing test machine was developed. This new test machine, which is based on the principle of the scanning force controlled probe microscope, can realize nano/micro-mechanical machining and in-process profile measurement. Experimental results of nano/micro indentation and scratching show that the controllable cutting depth of the test machine can be controlled by PZT actuator. Profile measurement of the machined surface has also been performed by using the test machine and a conventional AFM(Atomic Force Microscopy). A good agreement of the two measurement results have been achieved.

• 구강회복응용과학지
• /
• 제23권3호
• /
• pp.249-257
• /
• 2007

State of problem : The use of zirconium oxide all-ceramic material provides several advantages, including a high flexural strength(>1000MPa) and desirable optical properties, such as shading adaptation to the basic shades and a reduction in the layer thickness. Along with the strength of the materials, the cementation technique is also important to the clinical success of a restoration. Nevertheless, little information is available on the effect of different surface treatments on the bonding of zirconium high-crystalline ceramics and resin luting agents. Purpose : The aim of this study was to test the effects of surface treatments of zirconium on shear bond strengths between bovine teeth and a zirconia ceramic and evaluate differences among cements Material and methods : 54 sound bovine teeth extracted within a 1 months, were used. They were frozen in distilled water. These were rinsed by tap water to confirm that no granulation tissues have left. These were kept refrigerated at $4^{\circ}C$ until tested. Each tooth was placed horizontally at a plastic cylinder (diameter 20mm), and embedded in epoxy resin. Teeth were sectioned with diamond burs to expose dentin and grinded with #600 silicon carbide paper. To make sure there was no enamel left, each was observed under an optical microscope. 54 prefabricated zirconium oxide ceramic copings(Lava, 3M ESPE, USA) were assigned into 3 groups ; control, airborne-abraded with $110{\mu}m$ $Al_2O_3$ and scratched with diamond burs at 4 directions. They were cemented with a seating force of 10 ㎏ per tooth, using resin luting cement(Panavia $F^{(R)}$), resin cement(Superbond $C&B^{(R)}$), and resin modified GI cement(Rely X $Luting^{(R)}$). Those were thermocycled at $5^{\circ}C$ and $55^{\circ}C$ for 5000 cycles with a 30 second dwell time, and then shear bond strength was determined in a universal test machine(Model 4200, Instron Co., Canton, USA). The crosshead speed was 1 mm/min. The result was analyzed with one-way analysis of variance(ANOVA) and the Tukey test at a significance level of P<0.05. Results : Superbond $C&B^{(R)}$ at scratching with diamond burs showed the highest shear bond strength than others (p<.05). For Panavia $F^{(R)}$, groups of scratching and sandblasting showed significantly higher shear bond strength than control group(p<.05). For Rely X $Luting^{(R)}$, only between scratching & control group, significantly different shear bond strength was observed(p<.05). Conclusion : Within the limitation of this study, Superbond $C&B^{(R)}$ showed clinically acceptable shear bond between bovine teeth & zirconia ceramics regardless of surface treatments. For the surface treatment, scratching increased shear bond strength. Increase of shear bond strength by sandblasting with $110{\mu}m$ $Al_2O_3$ was not statistically different.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2005년도 춘계학술대회 논문집
• /
• pp.395-400
• /
• 2005

Nano-scale fabrication of silicon substrate based on the use of atomic force microscopy (AFM) was demonstrated. A specially designed cantilever with diamond tip, allowing the formation of damaged layer on silicon substrate by a simple scratching process, has been applied instead of conventional silicon cantilever for scanning. A thin damaged layer forms in the substrate at the diamond tip-sample junction along scanning path of the tip. The damaged layer withstands against wet chemical etching in aqueous KOH solution. Diamond tip acts as a patterning tool like mask film for lithography process. Hence these sequential processes, called tribo-nanolithography, TNL, can fabricate 2D or 3D micro structures in nanometer range. This study demonstrates the novel fabrication processes of the micro cantilever and diamond tip as a tool for TNL using micro-patterning, wet chemical etching and CVD. The developed TNL tools show outstanding machinability against single crystal silicon wafer. Hence, they are expected to have a possibility for industrial applications as a micro-to-nano machining tool.

• Journal of Preventive Medicine and Public Health
• /
• 제29권2호
• /
• pp.359-370
• /
• 1996

An outbreak of dermatosis occurred at a machine manufacture factory in Kyongju on Aug 1995. Authors conducted a questionnaire ,survey among 92 workers in the factory and a dermatologist examined their skin lesions. Authors also collected moths and identified them. The results are as follows; 1. Forty-two cases of dermatosis were identified with attack rate of 45.7%. Attack rate was not different by company, age, sex, educational level and duration of employment. Attack rate was 47.8% among productive workers, 25.0% among clerical workers and 100.0 % among patrolmen. 2. Two cases among 42 dermatosis cases and three subjects among 50 non-cases had a history of same dermatosis last year. Four of dermatosis cases had a history of dermatosis among their family members. 3. Skin lesions of the cases were scattered or grouped rice-sized erythematous papules or vesicles. Duration of dermatosis from the onset to the time of survey was from one day to more than 30 days. The most frequent site of skin lesion was the arms(81.0 %), and it was also observed at the neck(47.6 %), abdomen(45.2 %), chest(42.9 %), legs(38.1 %) and back(35.7 %). Skin lesion was aggravated with sweating(31.0 %), after shower(16.7 %) and with scratching(11.9 %). 4. Moths were collected and identified as Euproctis subflava (Bremer). Many poisonous stings were observed on their wngs which is harmful to human. 5. Contact with moths' wing droppings to two authors on thier forearms for provocation resulted in severe immediate pain followed by prolonged pruritus. Erythematous macules quickly appeared and succeeded by firm wheal-like red papules. Authors thought that the outbreak of dermatosis was brought about by Euproctis subflava (Bremer). Further studies on the factors contributing to the prosperity of the moths in this area are needed.