• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.20 no.3
• /
• pp.263-271
• /
• 2010

A reaction wheel is commonly used, as an important actuator, to control the attitude of a satellite. Operation of the reaction wheel plays a role of an excitation source to loading equipment inside the satellite. As requirements for environmental vibration to manifest the performance of precision equipment are getting more stringent, the research for analysis or reduction of unwanted action force in high frequency range when operating the reaction wheel is necessary. In this paper, the procedure to extract input forces and damping of a rotor system of reaction wheel is suggested. The analysis for measured action forces of reaction wheel is accomplished and important higher harmonics of action forces are determined. The input forces and damping of the rotor system are, then, extracted by curve-fitting and a particular solution for input force.

• Bulletin of the Korean Space Science Society
• /
• 2005.04a
• /
• pp.138-142
• /
• 2005

A reaction wheel, an actuator for satellite attitude control, produces disturbance torque and force as well as its axial control torque. The disturbances have an influence on the pointing stability of high precision satellites. The measurement of disturbances for such a satellite, therefore, is necessary. The wheel's rotation, however, causes the vibration of the table and its vibration induces measurement errors, especially large near the resonance frequency of the Measurement table. For the purpose of overcoming these defects, a calibration method using frequency compensation is suggested in this paper. Disturbance parameters are identified from data examined by frequency compensation. Measurement frequency range can be expanded far higher than the resonance frequency, since the degradation of data accuracy caused by its vibration is well alleviated even in the resonance area.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.43 no.7
• /
• pp.635-640
• /
• 2015

In this paper, we report a non-explosive separation device for a small satellite which utilize a shape memory alloy actuator. Based on previous research, we try to increase the reliability of the proposed device by changing some components. It enables the proposed device to activate under high preload. Also, we confirm it generates low shock which is main advantage of non-explosive separation device. Finally, vibration test which mimics launching environment and thermal vacuum test which mimics space environment are carried out respectively. After each environment test, we confirm the proposed device is successfully activated. Conclusively, we develop a non-explosive separation device which can activate with low shock under high preload after shock and environment tests(vibration and thermal vacuum tests).

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.36 no.7
• /
• pp.651-657
• /
• 2008

A new approach for maximizing torque capability of low efficient reaction wheel assembly is addressed in this paper. At first, to find out a solution in constrainted field, weighted pseudo-inverse and momentum minimized allocation are suggested instead of a general control allocation called pseudo-inverse. The second method is a structural manner to enlarge torque capability of specific axis by changing installed skew angle of wheels. Two proposed methods are applied to large angle maneuvers of satellite. Improvement of control performance and feasibility for applying to commercial satellite attitude control are demonstrated by numeric simulations.

• Smart Structures and Systems
• /
• v.16 no.1
• /
• pp.27-46
• /
• 2015

Active surface adjustment of cable net structures is becoming significant when large-size cable net structures are widely applied in various fields, especially in satellite antennas. A general-duty adjustment method based on active cables is proposed to achieve active surface adjustment or surface profile reconfiguration of cable net structures. Piezoelectric actuators and voice coil actuators are selected for constructing active cable structures and their simplified mechanical models are proposed. A bilevel optimization model of active surface adjustment is proposed based on the nonlinear static model established by the direct stiffness method. A pattern search algorithm combined with the trust region method is developed to solve this optimization problem. Numerical examples of a parabolic cable net reflector are analyzed and different distribution types of active cables are compared.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.38 no.4
• /
• pp.321-326
• /
• 2010

The non-explosive release device using jack mechanism is designed and fabricated for the small satellite. As a triggering actuator for the release device, a piezo rotory motor with torque of more than $1.7kgf{\cdot}cm$ is employed to guarantee stable activation. For performance tests of separation device, we conducted release time test, preload test and shock test. The device was operated within 1.172sec and activated stably under load of 45kgf. Maximum shock was measured as 18G that is much less than the pyro-separation device produces. We confirmed the possibility as a satellite separation device through above presented tests.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.41 no.2
• /
• pp.150-155
• /
• 2013

We present a kevlar rope based Non-Explosive Actuator(NEA) device which has simple structure and is activated by burning Ni-Cr wire. Through performance test, we find it can be operated under various pre-load by simply changing turn number of Ni-Cr wire. It shows release time of 680ms and shock level of 110G under pre-load of 6.0kN. Launching environment and space environment tests are planned to verify performance of the NEA based on European Satellite Agency test manual. Conclusively, we expect the proposed NEA can be applicable to release solar panel and fairing separation.

• Journal of the Korean Vacuum Society
• /
• v.21 no.6
• /
• pp.287-294
• /
• 2012

In the high vacuum condition of the space, outgassing from any assembly of satellite can contaminate satellites, especially second surface mirror and optical lens, it cause satellite to fail in own missions. Therefore, all unit shall be check for compatibility with vacuum using CVCM (Collected Volatile Condensable Material) and TML (Total Mass Loss) in advance. CVCM and TML of the PZT-5 piezoelectric ceramic vibrator has less than 0.1% and 1.0% respectively. Also, it has less than 500 $ng/cm^2/hr$ of Thermoelectric Quartz Crystal Microbalance for vacuum bake-out test using high temperature(more than $80^{\circ}C$) and high vacuum (less than $5.0{\times}10^{-3}$ Pa). Thus, piezoelectric ceramic vibrator may be employed in the vacuum environments. Finally, it can be confirmed that the characteristics change of the piezoelectric ceramic vibrator is less than 1% under vacuum environments.

• Bulletin of the Korean Space Science Society
• /
• 2008.10a
• /
• pp.36.1-36.1
• /
• 2008

An Unscented Kalman Filter(UKF) for estimation of attitude and rate of a spacecraft using only magnetometer vector measurement is presented. The dynamics used in the filter is nonlinear rotational equation which is augmented by the quaternion kinematics to construct a process model. The filter is designed for low Earth orbit satellite, so the disturbance torques include gravity-gradient torque, magnetic disturbance torque, and aerodynamic drag. The magnetometer measurements are simulated based on time-varying position of the spacecraft. The filter has been tested not only in the standby mode but also in the detumbling mode. To stabilize the attitude, linear PD controller is applied and the actuator is assumed to be thruster. A Monte-Carlo simulation has been done to guarantee the stability of the filter performance to the various initial conditions. The UKF performance is compared to that of EKF and it reveals that UKF outperforms EKF.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.43 no.8
• /
• pp.757-764
• /
• 2015

Mathematical modeling of focal plane compensation device in the small earth-observation satellite camera has been conducted experimently for compensation of micro-vibration disturbance. The PZT actuators are used as control actuators for compensation device. It is quite difficult to build up mathematical model because of hysteresis characteristic of PZT actuators. Therefore, the compensation device system is assumed as a $2^{nd}$ order linear system and modeled by using MATLAB System Identification Toolbox. It has been found that four linear models of compensation device are needed to meet 10% error in the input frequency range of 0~50Hz. These models describe accurately the dynamics of compensation device in the 4 divided domains of the input frequency range of 0~50Hz, respectively. Micro-vibration disturbance can be compensated by feedback control strategy of switching four models appropriately according to the input frequency.