• 한국해양공학회지
• /
• 제29권4호
• /
• pp.300-308
• /
• 2015

With the increases in oil and gas prices, and energy consumption, drillship construction has increased during the last decade. A drillship using a dynamic positioning (DP) system to maintain its position and heading angle during drilling operations. In addition, a drillship is equipped with a moonpool structure to allow its drilling systems to be operated in the midship section. A drillship for the North Sea is specially designed to endure harsh environmental loads. For safe operation in the North Sea, the drillship should have good motion response and robust hull strength. A break water should be considered on the bow and side deck to prevent the green water on deck phenomenon from incoming waves. In addition, the moonpool should be designed to reduce the speed loss and resonance motion. In this study, the hydrodynamic characteristics of a drillship for the North Sea were examined in relation to the motion, wave loads, green water, and moonpool resonance in the initial design stage.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1995년도 추계학술대회 논문집 학회본부
• /
• pp.268-270
• /
• 1995

In crane drives, DC motor has been most widely used due to simple control characteristic and favorable transient behavior. Nowadays, however, the squirrel cage induction motor is known as an attractive candidate due to elimination of all sliding electrical contacts, resulting in an exceedingly simple and rugged construction. Especially, in hoist application, the smooth torque control and four quadrant operation are essential. In this paper, an operation of dual inverters with common DC bus fed by vector controlled induction motor is described. Single DSP is employed as a main processor to control dual inverters and communicates each input/output signal with PLC. As well as giving a detailed expression, full simulation and experimental results are presented.

• 대한조선학회논문집
• /
• 제49권6호
• /
• pp.504-511
• /
• 2012

The objective of this study is to investigate tank container to be used as fuel tank for LNG fueled ship. Feasibility of tank container to the fuel tank of LNG fueled ship is addressed and the advantage of tank container as fuel tank of ship is investigated. Conceptual configuration of the tank container is designed as well as structural analyses based on finite element method are carried out to meet the design regulation suggested by shipping register. Static loading is considered by structural analysis and impact test is performed. It is necessary to require SRS(shock response spectrum) in order to investigate structural safety which can meet.

• International Journal of Naval Architecture and Ocean Engineering
• /
• 제3권1호
• /
• pp.95-104
• /
• 2011

As sea state harsher in the ocean space, more large motion and wave loads occurs on ships hull by non-linear phenomena. To consider nonlinear effect on ships hull in the structural design verification, the direct calculation method with numerical approach is used rather than rule values for the reliable accuracy. In this paper, the non-linear wave loads analysis in time domain is performed by using a Rankine Panel Method together with numerical schemes. Linear calculations have been carried out based on DNV CSA-2 notation to generate the motion responses and wave loads of large ships. By short and long term analysis, the design wave amplitudes are selected for the nonlinear analysis. The maximum wave induced bending moment in hogging and sagging conditions are calculated in the nonlinear analysis. Also, the green water effect on the wave induced vertical bending moment was investigated. The results show the vertical bending moments are more influenced by green water in sagging condition than in hogging condition due to green water loading.

• 한국해양공학회:학술대회논문집
• /
• 한국해양공학회 2004년도 학술대회지
• /
• pp.188-192
• /
• 2004

A Numerical analysis method is developed in order to compute the flaw and wave field for 2-dimensional floating body in the free roll motion with 3 degrees of freedom. Navier-Stokes and continuity equations are gaverning equations in tire present study. Finite Difference method is introduced to discretize the governing equation. The free surface is traced by the interface tracking method and the grid system is fitted to boundaries including free surface and body surface, which is moving in the flow field. The numerical scheme is based on Maker and Cell method. For the sake of validation of the numerical method, the computed roll decay factors according to tire midship section shapes are compared with measured results. The numerical results are discussed in order to understand the effect of midship section shape on roll motion.

• Journal of Welding and Joining
• /
• 제31권6호
• /
• pp.37-43
• /
• 2013

This study targets to make clear the connection between MS (Martensite start) point and welding shrinkage. We approved that a Martensite-transformed weldment may not yield state under low MS point, but also admitted the limitation of numerical calculation by inherent strain approach or thermal strain approach. Therefore, new thermal strain formulae during cooling stages were made. As a thermal strain is obtained by integrating thermal extension coefficient, a constant of integration should be decided. In our suggested formulae, the origin was based on totally remained austenite, and added strain from volume changes in Martensite transformation was based on totally transformed ferrite. Through the suggested methodology, It is verified that an MS point under a critical temperature can let weld shrinkage relax and the critical value can be obtained. For supporting this process, 15 weld-consumables were made, were tested by fillet type and were measured. As a result, a positive correlation between MS point and level of weld-distortion was obtained, but it was rather weak.

• 한국해양공학회지
• /
• 제33권5호
• /
• pp.479-485
• /
• 2019

As exhaust gas systems of ships become more complicated, it is necessary to calculate an accurate pressure loss at their design stage. If the dynamic loss coefficients of non-standard fittings mainly used in exhaust gas pipe (EGP) are well-documented, it would be possible to calculate precise pressure loss more readily than using the conventional method that analyzes the entire system. In the case of a ship's EGP, the flow rates and temperatures of exhaust gas are determined by engine specifications, and the range of the flow rate and temperature is limited according to operating conditions. In addition, as it is possible to define non-standard fittings frequently used in an EGP, a database can be easily constructed and effective. This paper illustrates effective parameters and analysis cases of several types of non-standard fittings mounted in ship EGPs. The analysis procedure proposed in this paper is verified using existing research results on HVAC fittings. The numerical procedure, which is minimally affected by manpower and grid, is established such that it can be applied at the industry level.

• 대한조선학회논문집
• /
• 제56권2호
• /
• pp.152-160
• /
• 2019

In this study, we propose a piping material supply management method using CAD system. The piping materials installed in super large offshore plants have very complicated connection conditions. Therefore, it is very difficult to determine the order of receipt of a large number of installation materials. Therefore, we have developed a system that can automatically check the preparation rate of installation materials prior to the installation process. We have developed an algorithm to obtain connection information among installation items from PDMS system. We have developed an algorithm that can determine the order of installation materials to be installed using the connection information. The order of the installation material is determined by taking into account the constraint conditions for the complete installation of the piping material. We confirm the effectiveness of the developed algorithms in the operating system. This system is also used to manage installation schedules and plan the installation manpower.

• International Journal of Korean Welding Society
• /
• 제3권1호
• /
• pp.34-38
• /
• 2003

It has been used many kinds of horizontal butt-welding methods at block-to-block erection stage in shipbuilding companies. For examples, some companies use conventional FCAW process with one side or both sides groove joint welding, others use carriage with torch holder type mechanized welding method. Although lots of efforts were done until now, some problems in quality and productivity still remain in ship's hull welding. In this study, we have attempted to raise productivity and quality on horizontal position of welding with following 3 items. 1) Prepare groove condition with no root gap for making easy fit-up work. 2) Develop improved MAG (100% $CO_2$ gas shielding) welding process with solid wire for making sound root bead from one side. 3) Develop and apply quite new automatic welding carriage. The stability of new welding process was confirmed by conducting mechanical tests of weldments to verify the soundness of weldments.

• 한국해양공학회지
• /
• 제32권1호
• /
• pp.21-27
• /
• 2018

The design and analysis of a quayside mooring system for safe mooring of Prelude FLNG under extreme environmental conditions were carried out. The design of the mooring system considered the yard operation conditions and maximum wind speed during a typhoon. In order to secure the mooring safety of Prelude FLNG under an extreme environment, a special steel structure was designed between the quay and Prelude FLNG to maintain the distance from the quay to a certain extent to avoid a collision with the inclined base. The mooring safety was also ensured by installing additional new parts on the quay. A mooring analysis and mooring safety review were performed with more rigorous modeling considering the nonlinearity of the mooring rope and fender. In order to secure additional safety of the mooring system under extreme environmental conditions, a safety assessment was conducted on the failures of the mooring components proposed in the marine mooring guidelines. Based on the results of the mooring analysis, it was confirmed that the Prelude FLNG can be safely moored even under the extreme conditions of typhoons, and a worst case scenario analysis verified that the mooring system design was robust enough. The proposed mooring analysis and design method will provide a basis for the safe mooring of ultra-large floating offshore structures of similar size in the future.