• Journal of Welding and Joining
• /
• v.17 no.4
• /
• pp.1-5
• /
• 1999

Servo Gun은 기존의 일반적인 Spot용접Gun에서 가압 및 개방에 사용되는 Air Cylinder를 Servo Motor로 대치한 신개념의 Spot용접Gun으로 여러 가지의 우수한 기능과 특징을 가지고 있어 적 용범위의 확대가 기대되고 있다.

• Journal of Welding and Joining
• /
• v.17 no.5
• /
• pp.77-82
• /
• 1999

Resistance spot welding process is completed in very short time and there are many factors affecting on the generation of heat. It is difficult to control these experimental factors and monitor distribution of the temperature and stresses in the experimental analysis case. and too much time and expense are required for the experimental trials to fine proper welding condition. So numerical analyses have been attempted steadily, but most numerical analyses on the resistance spot welding are mainly focused on thermal behavior. Therefore, in this paper, the numerical analysis of mechanical behavior as well as heat conduction is carried out for the spot welding process. For this numerical analysis, axial symmetric computer program for the spot welding analysis by F.E.M. has been developed considering heat conduction and thermal elastic-plastic theory. Material properties depending on temperature such as density, heat conductivity, heat expansion coefficient, specific heat, yield stress, elastic modulus, and specific resistance are considered. Using the results of temperature distribution obtained from heat conduction analysis, the thermal elastic-plastic analysis is carried out to clarify mechanical behavior of spot welded specimen. In order to evaluate the effect of residual stresses, numerical analyses are carried out under tension-shear load in two cases respectively; one with residual stress, the other without residual stresses.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.13 no.5
• /
• pp.42-49
• /
• 2005

In general, multi-lap spot weld joints are frequently present in automobile. Most research, however, has been focused on the single-lap spot weld joints until now. In this paper, tensile-shear strength tests are performed to examine the weldability of 3-lap spot joint welded by using the high strength steel sheet and the zinc coated steel sheet. The indentation depth and nugget diameter are used to propose the optimum welding conditions. The weldability is affected by the welding current and welding time for 3-lap spot joint. Meanwhile the expulsions is round to decrease with the increase of electrode force. The optimum welding conditions are presented for 3-lap spot joints of high strength steel sheet and zinc coated steel sheet.

• Proceedings of the KWS Conference
• /
• 2005.06a
• /
• pp.285-287
• /
• 2005

During fabrication of deck house block in passenger ships, the problem of unexpected large deformation and distortion frequently occurs. In this case, line and spot heating method were widely used to correct the distortion of thin plate structure. Spot heating was especially used for the case under 5mm thickness. Few papers are available on the working conditions of spot heating method but only little information on deformation control. In this study, evaluation was carried out on the temperature distribution of spot heating methods using FEA and practical experiments for various heating time. IIn FEA, heat input model was established using Tsuji's double Gaussian heat input mode (Tsuji, I., 1988). This model was verified by comparing with experimental data. Also radial shrinkage and angular distortion due to spot heating were determined and compared with experimental results. Thermo elasto-plastic analysis was performed using commercial FE code, MSC/MARC. Radial shrinkage and angular distortion were measured using 3D measuring apparatus. Based on these results, simplified analysis model for deformation by spot heating was established.

• The Journal of Asian Finance, Economics and Business
• /
• v.7 no.8
• /
• pp.51-59
• /
• 2020

The objective of this study is to enrich the literature by investigating the impact of introduction of index future trading on spot market returns and trading volume in Vietnam. Data used in this study mainly consist of daily VN30-Index and market trading volume series during the period from February 6^th, 2012 to December 31^st, 2019. Using OLS, GARCH(1,1) and EGARCH(1,1) models, the empirical findings consistently confirm that the introduction of index future trading has no impact on the spot market returns. In addition, the results of the EGARCH(1,1) model indicate that the leverage effect on the spot market volatility is existence in HOSE. Specifically, bad news has a greater effect on the market volatility than good news of the same size. Moreover, our empirical findings reveal that the introduction of index future contracts has the positive impact on the underlying market trading volume. Specifically, the trading volume of the post-index futures introduction increases by 7.5 percent compared with the pre-index futures introduction. Finally, the results obtained from the Granger causality test for the relationship between the spot market returns and the future trading activity confirm that only uni-directional causality running from the market returns to the future trading activity exists in HOSE.

• Proceedings of the KSRS Conference
• /
• 2003.11a
• /
• pp.760-762
• /
• 2003

This study confirmed the usefulness of short-wavelength infrared (SWIR) in the discrimination and classification of evergreen forest types. A forested area near Hisayama and Sasaguri in Fukuoka Prefecture, Japan, served as the study area. Warm-temperate forest vegetation dominates the study site vegetation. Coniferous plantation forest, natural broad-leaved forest, and bamboo forest were analyzed using LANDSAT5/TM and SPOT4/HRVIR remote sensing data. Samples were extracted for the three forest types, and reflectance factors were compared for each band. Kappa coefficients of various band combinations were also compared by classification accuracy. For the LANDSAT5/TM data observed in April, October, and November, Bands 5 and 7 showed significant differences between bamboo, broad-leaved, and coniferous forests. The same significant difference was not recognized in the visible or near-infrared regions. Classification accuracy, determined by supervised classification, indicated distinct improvements in band combinations with SWIR, as compared to those without SWIR. Similar results were found for both LANDSAT5/TM and SPOT4/HRVIR data. This study identified obvious advantages in using SWIR data in forest-type discrimination and classification.

• Proceedings of the KSRS Conference
• /
• 2008.03a
• /
• pp.80-85
• /
• 2008

최근 도심지역이 급변하고 고해상도 위성영상의 보급이 증가함에 따라 고해상도 위성영상을 이용한 수치표고모델과 정사영상 생성에 관한 연구가 활발해 지고 있다. 본 연구에서는 IKONOS, SPOT5, QUICKBIRD, KOMPSAT2 위성영상을 이용하여 DEM 과 정사영상을 생성하였으며 USGS DTED 와 기준점을 이용하여 결과의 정확도를 비교 분석하였다. 보다 정확한 DEM 생성을 위해 자동 피라미드 알고리즘을 적용하고 영상 정합시 에피폴라 기하학을 적용하였다. 정사 영상 생성시 DTED 높이값을 이용하여 보정을 수행하였으며 생성 속도를 높이기 위하여 리샘플링 그리드를 적용하였다. 본 연구에서 DEM 과 정사영상 생성시 QUICKBIRD 와 SPOT5 의 경우 영상의 용량이 매우 커 메모리 부족문제와 알고리즘 수행 속도 저하가 발생함을 확인하였다. 이를 개선하기 위하여 DEM 생성시 정합 후보점의 개수를 줄이는 알고리즘을 고안하여 기존에 메모리 문제로 생성하지 못했던 QUICKBIRD와 SPOT5 의 DEM 을 생성하였으며 정사 영상 생성시 리샘플링 그리드를 적용하여 고해상도 정상영상 생성 속도 개선에 상당한 효과를 가져왔다. 그러나 고해상도 위성 영상의 용량이 점점 커져감에 따라 이러한 메모리 문제와 처리 속도 저하에 관한 문제는 추후 계속적으로 연구되어야 할 부분이라고 할 수 있다. 본 연구에서 생성한 IKONOS, SPOT5, QUICKBIRD DEM 의 정확도를 USGS DTED 와 비교한 결과 13${\sim}$15 m 정도의 RMS 높이 오차가 산출되었으며 생성된 IKONOS, QUICKBIRD, KOMPSAT2 정사영상을 기준점과 비교한 결과 3 m 정도의 거리오차가 산출되었음을 확인하였다.

• Korean Journal of Microbiology
• /
• v.38 no.4
• /
• pp.247-253
• /
• 2002

The cellular responses of TNT-degrading bacterium, Stenotrophomonas sp. OK-5 to explosive 2,4,6-trini-trotoluene (TNT) as an environmental contaminant were examined. Survival of the strain OK-5 with time in the presence of different concentrations of TNT under sublethal conditions was monitored, and viable counts paralleled the production of the stress shock proteins in this bacterium. Total cellular fatty acids analysis showed that strain OK-5 produced or disappeared several different kinds of lipids when grown on TNT media than when grown on TSA. Under scanning electron microscope, the cells treated with 0.5 mM TNT for 12 hrs showed irregular rod shapes with wrinkled surfaces. Analyses of SDS-PAGE and Western blot using anti-DnaK and anti-GroEL revealed that several stress shock proteins including 70 kDa DnaK and 60 kDa GroEL in strain OK-5 were newly synthesized at different TNT concentrations in exponentially growing cultures. 2-D PAGE of soluble protein fractions from the culture of OK-5 exposed to TNT demonstrated that approximately 300 spots were observed on the silver stained gel ranging from pH 3 to pH 10. Among them, 10 spots significantly induced and expressed in response to TNT were selected and analyzed. As the result of internal amino acid sequencing with ESI-Q TOF, two proteins, spot #1 and spot #10 were assigned the DnaK protein XF2340 of Xylella fastidiosa and stress-induced protein of Mesorhizobium loti, respectively.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.48 no.3
• /
• pp.235-241
• /
• 2012

The efficiency tests of automatic positioning transmitter (APT) using satellite on life jacket were carried out to minimize casualties of fishermen and to make system optimization for effective SAR (Search and Rescue) operation. As the result of the tests, average position was equaled on the comparison between SPOT using low earth orbit satellite and DGPS (Differential Global Positining System), but standard deviation of DGPS for latitude and longitude were 66.4% and 46.3% smaller than those of SPOT. The position precision of SPOT was almost two times lower than LGT using geostationary satellite to compare 95% circular error probability. However, the success rate of receiver for SPOT was revealed as 86.5~94.1% on the experiments in the South Sea and the West Sea and it was 4.5 times higher than LGT. Therefore, SPOT is expected to contribute greatly to the rapid rescue of victim.

• Transactions of Materials Processing
• /
• v.26 no.3
• /
• pp.174-180
• /
• 2017

In this study, a new spot welding with electric resistance heated dies is suggested for the spot welding of non-ferrous metal plates for drawing and concurrent spot welding. This welding method involves two heating processes such as heating by conduction of electric resistance heated dies and heating by resistance between contacted surfaces of two plates by welding current induced to copper dies for the fusion of contacted metal. This welding process has welding variables such as current induced in heated and copper dies, the inner diameters of heated dies, and edge shape of the copper dies. Experimental conditions for each current should be established to get successful welding strength. The welding strength could reach to the desired value in industrial fields under the following conditions of contact diameters of heated dies in this case of overlapped aluminum5052 plates with 0.3-mm thickness: inner and outer diameters of 5.0 and 16mm, respectively; diameter of copper dies, 5.0mm; heating current, 6.8kA in heated steel dies; welding current, 8.6 kA in copper dies.