• Journal of Welding and Joining
• /
• v.15 no.2
• /
• pp.54-63
• /
• 1997

For the purpose of establishing laser welding condition (laser power, welding speed and beam focus) and of evaluating tailored blanks for two kinds of thin steel sheets SPCC and SK5M using in the thin plate structure such as automobile, train, and so on, investigated their $CO^2$ laser weldability under various initial welding conditions. SPCC thin sheet showed good weldability under some welding conditions. But, high carbon steel sheet SK5M needed heat treatment after welding to obtain ductility of the welded joint. And next, tailored blank was tested through deep drawing to evaluate reliability of their obtained laser welding conditions. The forming depths by tailored blank were SPCC+SPCC=22-25mm and SK5M+SK5M=13-25mm.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 1996.03a
• /
• pp.159-164
• /
• 1996

For the purpose of establishing laser welding condition(laser power, welding speed and beam focus) and of evaluating tailor welded blank for three kinds of thin steel sheets of SPCC, SK5M and SUS304 using in the thin plate structure such as automobile, train and so on. Their $CO_2$ laser weldability were primarily tested under various welding condition. SPCC and SUS304 thin sheets showed good weldability under some welding condition. But, high carbon steel sheet SK5M needs heat treatment after welding to obtain higher tensile strength and ductility of the welded joint. And next, laser welding condition. Butt-welded specimens were not nearly broken at weld bead. However, base material were ruptured in the direction of circumference. The forming depths by tailor weld bead. However, base material were ruptured in the direction of circumference. The forming depths by tailor welded blank were SPCC+SPCC=22~25mm, SUS304+SUS304=25~43mm and SK5M+SK5M=13~17mm.

• Transactions of Materials Processing
• /
• v.7 no.4
• /
• pp.400-406
• /
• 1998

The press formability analysis of welding parts was studied in the current work by the tailor welded blank. The press formability was tested by means of the flash weldability and the formability for two kinds of materials (SPCC & S35C). The results indicate that SPCC & S35C steel sheets showed good weldability and formability after an optimum welding conditions. The independent operation variables were characterized by strength of welding parts, deformation after the welding, press formability of welding parts and productibility of welding. The weldability and the quality of welding parts of the flashed SPCC steel sheet was superior to those of the S35C steel sheet, since a higher carbon content in steel sheet led to a higher hardness. The experimental results were discussed by the evaluation of the results obtained from tensile test, hardness test, micro-structure and V bending test.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2009.10a
• /
• pp.252-253
• /
• 2009

희생양극으로 많이 활용되고 있는 Zn, Mg 금속은 모재 금속과 갈바닉 쌍을 형성하여 방식체를 보호하게 된다. 본 실험에서는 SPCC 강판위에 Fe+Mg, Fe+Zn 강판을 각각 제작하여 갈바닉 전류와 갈바닉 전위를 측정하였다. 갈바닉 전류는 초기에 금속 표면의 산화피막의 영향으로 큰값을 나타났으나, 시간의 경과에 따라 안정적인 값을 나타냈다. 즉, 가스압의 증가에 따라 제작된 Fe+Mg, Fe+Zn박막의 내식성은 우수하게 나타났고, 가스압이 낮을수록 박막의 내식성은 떨어지는 것으로 나타났다. 갈바닉 전위는 철의 방식전위에 도달하는 시간에 따라 내식성의 우수성을 판단하였다.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 1997.04a
• /
• pp.137-142
• /
• 1997

Spot welding has been used in the sheet metal joining processes because of its high productivity and convenience. In this study effects of welding conditions on the fatigue life and predicting methods of fatigue life of spot welded joint have been studied. Fatigue life was estimated by stress index parameter considering multiaxial stresses. Fatigue tests were conducted with the tensile-shear specimens using SPCC. Fatigue life of spot welded joint was influenced by welding currents and was predicted exactly with taking into account Stage III.

• The Journal of the Acoustical Society of Korea
• /
• v.36 no.6
• /
• pp.401-406
• /
• 2017

This paper presents the performance assessment of several key algorithms conducted for amphibian species sound classification. Firstly, 9 target species including endangered species are defined and a database of their sounds is built. For performance assessment, three feature vectors such as MFCC (Mel Frequency Cepstral Coefficient), RCGCC (Robust Compressive Gammachirp filterbank Cepstral Coefficient), and SPCC (Subspace Projection Cepstral Coefficient), and three classifiers such as GMM(Gaussian Mixture Model), SVM(Support Vector Machine), DBN-DNN(Deep Belief Network - Deep Neural Network) are considered. In addition, i-vector based classification system which is widely used for speaker recognition, is used to assess for this task. Experimental results indicate that, SPCC-SVM achieved the best performance with 98.81 % while other methods also attained good performance with above 90 %.

• Journal of Ocean Engineering and Technology
• /
• v.13 no.4 s.35
• /
• pp.55-62
• /
• 1999

Cold rolled steel has much plastic strain in the material surface produced by manufacturing process. The strain causes the variation of surface residual stress, in which influences the fatigue behavior under repeated loading. As experimental results, it was confirmed that the behavior of residual stress ${\sigma}_r$, with cycle N consisted of three stages except stress amplitude near fatigue limit in SPCC steel. On the first stage compressive residual stress decreased rapidly, on the second stage gradually, and on the last stage slightly. The relation between ${\sigma}_r$, and log N appeared linear behavior except the early part of cycle ratio $N/N_f$. The average gradient of ${\sigma}_r$, with respect to log N seemed to take a constant value without initial cycle ratio. On the other hand, the $N_f$ line was regressed by the first-order polynomial equation on ${\sigma}_r-log\;N_f$ diagram. Therefore, this study showed that both the gradient of ${\sigma}_r$, with respect to log N and the $N_f$ line was useful in predicting the cycle ratio $N/N_f$.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.24 no.2 s.173
• /
• pp.438-448
• /
• 2000

Mechanical press joining technique has been used in sheet metal joining processes because of its simple process and possibility of joining dissimiliar metals, such as steel and aluminum. The static and cyclic behavior of single overlap AI-alloy and steel(SPCC) joints has been investigate. Relationships were developed to estimate the strength of the joint taking into consideration base metal strength properties and the geometry of the joint. Fatigue test results have shown that fatigue resistance of the SPCC mechanical press joints is almost equal to that of the spot weld at the life of $10^6$ cycles. Also, the dissimilar material jointed specimen with upper SPCC plate and button diameter corresponding to the nugget diameter of the spot welded specimen has almost same strength as the same material jointed specimen and as the spot welded specimen.

• Journal of Power System Engineering
• /
• v.19 no.5
• /
• pp.38-44
• /
• 2015

The cold-rolled steel sheet for automobile is liable to corrosion, and will be painting in a variety of ways for the anticorrosive. This paper was coated on cold rolled steel (SPCC and SPFC590) for automobiles using five kinds of organic/inorganic hybrid solution. This was evaluated corrosion resistance and so on by the salt spray. Corrosion area was less according to increasing of curing time in 2 types of steel plate with 5 types of the coating solution. No.1 solution was showed the best corrosion resistance regardless of the kinds of the steel sheet. It is judged that the melamin hardner had the role of bridge between $SiO_2$ polysilicate and urethan resin. Other properties were excellent in all solution.

• Transactions of Materials Processing
• /
• v.8 no.1
• /
• pp.57-64
• /
• 1999

The press formability analysis of welding parts was studied in the current work by the tailor welded blank. As the body panel is used in the press forming of welding parts by a weld method of the tailor welded blank, the following conditions are demanded: 1) The strength of welding parts must be the higher than base metals. 2) After the welding, severe welding deformatins must be avoided. 3) The press formability of welding parts is similar to that of many base metals. 4) The productibility of a welding has to be higher. There are many welding methods satisfying these conditions, but the purpose of this study is to inbestigate the upset weldability and formability of the material (SPCC). SPCC steel sheet showed good weldability and formability under some welding conditions. The experimental results were discussed by the evaluation of the results obtained from tensile tests, hardness tests, micro-structures and Erichsen cup test was a little lower than that of parent material.