• Journal of Welding and Joining
• /
• 제12권4호
• /
• pp.41-49
• /
• 1994

This study is to compare the welding quality of API 5L-X65 Steel- pipe's for natural gas transmission piping applied by SAW at shop and by GTAW-SMAW at site. The results can be summarized as follows; 1) Tensile strength of the welded zone by SAW(611.5 MPa) and by GTAW-SMAW(608.6 MPa) was maintained greater than that of the base metal(583.5 MPa). 2) Hardness of the welded zone and HAZ by SAW(Hv 194.8) & GTAW-SMAW (Hv 196.1) was slightly increased above that of the base metal (Hv 168.8), but less than the maximum allowable hardness(Hv 248). 3) Impact value of the welded zone by SAW(126.8 J) & GTAW-SMAW(88 J) became lower than that of the base metal(282.5 J), but was above the requirement of API 5L(68J). 4) Microscopic structure of the welded zone and HAZ by both SAW & GTAW-SMAW became fine-grained.

• Steel and Composite Structures
• /
• 제11권3호
• /
• pp.225-232
• /
• 2011

In this study, the deflection and deformation behaviours of IPN80 steel beam and column were investigated under the different industrial loads. Single-sided welds were applied to IPN80 steel beams using shielded metal arc (SMAW) and metal inert gas welding (MIG) method in the form of T-type. After that, the performance of SMAW and MIG welded joints were identified using beam bending test under 500 and 3000 N loads. SMAW and MIG methods were compared with each other to understand the deflection and deformation behaviours of the welded steel structures. Lower deformation and deflection were obtained in MIG welded steel beams. The results show that, steel beams welded MIG method has higher load capacity than SMAW welded ones. MIG welding method is more reliable than the SMAW method for the combining performance and load capacity.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2002년도 춘계학술대회 논문집
• /
• pp.125-133
• /
• 2002

In this study, it was investigated about endurance limit and fatigue behavior of load carrying fillet welded cruciform joints according to welding methods of SMAW, SAW, MIG and FCAW commonly using for welding structures in present. Endurance limit carried omit highly in the order of SMAW, MIG, SAW, FCAW and fatigue crack propagation ratio carried out lowly in the order of SMAW, MIG, FCAW, SAW. By these results, it is needed to use SMAW or MIG welding methods for welding structures with small welding capacity and SAW or FCAW methods for large welding structures after due consideration about economic gains and operation efficiency of welding. Fatigue crack propagation ratio is more effected by strength of welding materials than endurance limit of welding materials according to welding methods.

• Journal of Welding and Joining
• /
• 제4권3호
• /
• pp.58-71
• /
• 1986

Mechanical and corrosion property of duplex stainless steel weldments made by the GTAW and SMAW process were studied. Fracture toughness, general and local corrosion resistance of GTAW and SMAW weldments were evaluated in terms of Charpy V notch impact test, anodic polarization diagram, pitting corrosion rate, respectively. SMA weld metal showed much lower impact toughness and higher ductile-brittle transition temperature than GTA weld metal. Fractographic and EDX analysis on fracture surface of SMA weld metal demonstrated the existence of (Si, Ti), oxide in large amounts. Potentiodynamic anodic polarization diagram of GMA weld metal showed much lower passive current density than SMA weld metal in 4% $H_2/SO_4$ solution. And pitting corrosion rate test showed the same tendency. Relating the microstructure, chemistry and property, it can be concluded that GTA weld metal gives better toughness due to lower oxygen content, i.e. lower inclusion content, and better corrosion resistance due to higher Pitting Index(PI) than SMA weld metal.

• 한국공작기계학회논문집
• /
• 제12권1호
• /
• pp.38-44
• /
• 2003

In this study, endurance limit and fatigue behavior of load carrying fillet welded cruciform joints depending on commonly used welding methods such as SMAW, SAW, MIG and FCAW are investigated. In respect of endurance limit SMAW specimen showes highest result, and then MIG, SAW, FCAW in descending order. However, SMAW specimen showes lowest crack growth rate and it followed by MIG, FCAW, SAW. By these results, it is needed to use SMAW or MIG welding methods for welding structures with small welding capacity and SAW or FCAW methods for large welding structures with respect to economic benefits and operation efficiency of welding. It was also shown fatigue crack growth rate was more influenced by the strenght of welding materials than the endurance limit of welding materials.

• 한국마린엔지니어링학회:학술대회논문집
• /
• 한국마린엔지니어링학회 2005년도 후기학술대회논문집
• /
• pp.226-227
• /
• 2005

In this study, it was investigated about endurance and fatigue crack propagation rate of according to welding methods of SMAW and FCAW commonly using for welding structures in present. Endurance limits carried out highly in the order of SMAW, FCAW and fatigue crack propagation rate out lowly in the order of SMAW, FCAW. By these results, it is needed to used SMAW welding methods for welding structures with small welding capacity and FCAW methods for large welding structures after consideration about economic gains and operation efficiency of welding. Fatigue crack propagation rate is more effected by strength of welding materials than endurance limit of welding materials according to welding methods..

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2006년 추계학술발표대회 개요집
• /
• pp.69-71
• /
• 2006

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2000년도 특별강연 및 추계학술발표대회 개요집
• /
• pp.137-140
• /
• 2000

• 한국기계가공학회지
• /
• 제5권4호
• /
• pp.65-71
• /
• 2006

The lightness of components required on marine and shipbuilding industry is requiring high strength of components. In particular, fatigue failure phenomena, which happen in metal, bring on danger in human life and property. Therefore, antifatigue failure technology takes an important part on current industries. In this study, it is investigated about endurance and fatigue crack propagation rate of according to welding methods such as SMAW, FCAW and SAW commonly used for welding structures in present. Endurance limits carried out highly in the order of SMAW, FCAW, SAW and fatigue crack propagation rate out lowly in the order of SMAW, FCAW, SAW. By these results, it is needed to use SMAW welding method for welding structures with small welding capacity and FCAW, SAW methods for large welding structures after consideration about economic gains and operation efficiency of welding. Fatigue crack propagation rate is more affected by strength of welding materials than endurance limit of welding materials according to welding methods.

• 한국해양공학회:학술대회논문집
• /
• 한국해양공학회 2003년도 추계학술대회 논문집
• /
• pp.97-99
• /
• 2003

In order to confirm the possibility of application of laser welding process to 2.25Cr-1Mo steel, the characteristic of residual stress distribution in welds by SMAW and $CO_{2}$ Laser welding process have been investigated and compared using the numerical analysis. As the Result of the numerical analysis, the possibility of application of laser welding process has been found out in respect to the welding residual stress distribution and mechanical properties in welds.