• Smart Structures and Systems
• /
• 제14권5호
• /
• pp.765-784
• /
• 2014

In comparison with conventional shape memory actuated structures, antagonistic shape memory alloy (SMA) actuators permits a fully reversible two-way response and higher response frequency. However, excessive internal stress could adversely reduce the stroke of the actuators under repeated use. The two-way shape memory effect might further decrease the range of the recovered strain under actuation of an antagonistic SMA actuator unless additional components (e.g., spring and stopper) are added to regain the overall actuation capability. In this paper, the performance of all four possible types of SMA actuation schemes is investigated in detail with emphasis on five key properties: recovered strain, cyclic degradation, response frequency, self-sensing control accuracy, and controllable maximum output. The testing parameters are chosen based on the maximization of recovered strain. Three types of these actuators are antagonistic SMA actuators, which drive with two active SMA wires in two directions. The antagonistic SMA actuator with an additional pair of springs exhibits wider displacement range, more stable performance under reuse, and faster response, although accurate control cannot be maintained under force interference. With two additional stoppers to prevent the over stretch of the spring, the results showed that the proposed structure could achieve significant improvement on all five properties. It can be concluded that, the last type actuator scheme with additional spring and stopper provide much better applicability than the other three in most conditions. The results of the performance analysis of all four SMA actuators could provide a solid basis for the practical design of SMA actuators.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2004년도 춘계학술발표대회 논문집
• /
• pp.127-130
• /
• 2004

In this paper, active shape control of composite structure actuated by shape memory alloy (SMA) wires is presented. Hybrid composite structure was established by attaching SMA actuators on the surfaces of graphite/epoxy composite beam using bolt-joint connectors. SMA actuators were activated by phase transformation, which induced by temperature rising over austenite finish temperatures. In this paper, electrical resistive heating was applied to the hybrid composite structures to activate the SMA actuators. For faster and more accurate shape or deflection control of the hybrid composite structure, PID feedback controller was designed from numerical simulations and experimentally applied to the SMA actuators.

• International Journal of Control, Automation, and Systems
• /
• 제4권6호
• /
• pp.756-762
• /
• 2006

Shape Memory Alloy(SMA) actuators, which have the ability to return to a predetermined shape when heated, have many potential applications such as aeronautics, surgical tools, robotics and so on. Although the conventional PID controller can be used with slow response systems, there has been limited success in precise motion control of SMA actuators, since the systems are disturbed by unknown factors beside their inherent nonlinear hysteresis and changes in the surrounding environment of the systems. This paper presents a new development of a SMA position control system by using a self-tuning fuzzy PID controller. This control algorithm is used by tuning the parameters of the PID controller thereby integrating fuzzy inference and producing a fuzzy adaptive PID controller, which can then be used to improve the control performance of nonlinear systems. The experimental results of position control of SMA actuators using conventional and self-tuning fuzzy PID controllers are both included in this paper.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 2002년도 봄 학술발표회 논문집
• /
• pp.478-485
• /
• 2002

The shape memory alloys (SMAs) are often used in smart materials and structures as the active components. Their ability to provide a high recovery force and a large displacement has been used in many applications. In this paper the radial displacement of an externally pressurized elliptic composite cylinder where SMA liner or strips actuators are bonded on its inner or outer surface is investigated numerically. The elliptic composite cylinders consisting of an inlet duct system with SMAs are designed and analyzed to determine the feasibility of such a system for the removal of stiffeners from an externally pressurized duct of an aircraft inlet. The deformations caused by prestrained SMAs placed on either surface of an elliptic composite cylinder are studied when activated. The externally pressurized elliptic composite cylinders with the SMA actuators were analyzed using the 3-D finite element method incorporated with 3-D SMA behaviors. The results show that the role of stiffeners may be switched by the activated light SMA actuators.

• Composites Research
• /
• 제17권4호
• /
• pp.18-24
• /
• 2004

본 논문에서는 복합재 구조물에 대하여 형상기억합금 선을 이용한 능동 형상 제어에 관한 연구를 수행하였다. 형상기억합금 선의 열-기계적인 특성을 실험적으로 측정하였으며, 복합재 보 시편의 표면에 볼트를 이용하여 형상기억합금 작동기를 고정하는 방법으로 하이브리드 복합재 구조물을 제작하였다 형상기억합금 작동기는 온도 상승에 의한 상변화에 의해 작동되며, 본 연구에서는 형상기억합금 작동기에 전력을 가하여 내부 저항을 통해 발생하는 열을 이용하여 구동하였다. 보다 빠르고 정확한 형상 및 변형 제어를 위하여 수치적 시뮬레이션을 통한 PID 되먹임 제어기를 설계하였으며, 형상기억합금 작동기에 적용하는 실험을 수행하였다.

• Composites Research
• /
• 제12권3호
• /
• pp.45-54
• /
• 1999

본 연구에서는 형상기억합금 선을 편심하게 삽입한 복합적층 보의 좌굴 및 좌굴후 제어에 관한 실험결과를 나타내었다. 임계좌굴하중을 향상하기 위하여 형상회복모멘트의 특성을 활용하였다. 좌굴제어의 범위를 향상시키기 위해 페루프 제어를 사용하여 좌굴후 제어의 거동을 검토하였다. 이러한 좌굴제어 실험을 통하여, 임계좌굴하중을 증가시키고 좌굴모드가 반대방향으로 변화하는 거동을 보의 세장비 및 기하학적 초기결함, 형상기억합금 선의 삽입 위치 등을 고려하여 하중-변위의 결과로부터 정량적, 정성적으로 분석하였다. 적당한 형상회복모멘토를 이용하여 원하는 변형형상을 유지함으로써 외부하중을 받는 보의 좌굴후 제어에서도 적용할 수 있다.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2005년도 춘계학술대회 논문집
• /
• pp.1812-1818
• /
• 2005

Even though SMA actuators have high power to volume ratio, there exist disadvantages such as hysteresis and saturation. So the model identification for SMA actuators is very difficult. For the qualitative model identification, we described the behavior of SMA actuators using a so-called diagonal model, which can readily expect the turning point of an incomplete phase transformation. For the quantitative model identification, we developed the general dynamics of SMA actuators using the modified Liang's model. Using this dynamics we can describe the hysteresis and the saturation very well. It is also very important to notice that the modified Liang's model maintains a continuous martensite fraction at the change of the phase transformation but the original model cannot.

• Smart Structures and Systems
• /
• 제3권2호
• /
• pp.189-200
• /
• 2007

As a functional material, shape memory alloy (SMA) has attracted much attention and research effort to explore its unique properties and its applications in the past few decades. Some of its properties, in particular the electrical resistance (ER) based self-sensing property of SMA, have not been fully studied. Electrical resistance of an SMA wire varies during its phase transformation. This variation is an inherent property of the SMA wire, although it is highly nonlinear with hysteresis. The relationship between the displacement and the electrical resistance of an SMA wire is deterministic and repeatable to some degree, therefore enabling the self-sensing ability of the SMA. The potential of this self-sensing ability has not received sufficient exploration so far, and even the previous studies in literature lack generality. This paper concerns the utilization of the self-sensing property of a spring-biased Nickel-Titanium (Nitinol) SMA actuator for two applications: ER feedback position control of an SMA actuator without a position sensor, and estimation of the opening of a SMA actuated valve. The use of the self-sensing property eliminates the need for a position sensor, therefore reducing the cost and size of an SMA actuator assembly. Two experimental apparatuses are fabricated to facilitate the two proposed applications, respectively. Based on open-loop testing results, the curve fitting technique is used to represent the nonlinear relationships between the displacement and the electrical resistance of the two SMA wire actuators. Using the mathematical models of the two SMA actuators, respectively, a proportional plus derivative controller is designed for control of the SMA wire actuator using only electrical resistance feedback. Consequently, the opening of the SMA actuated valve can be estimated without using an extra sensor.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2004년도 추계학술발표대회 논문집
• /
• pp.278-281
• /
• 2004

In this paper, the thermomechanical responses of shape memory alloy (SMA) actuators and their applications as the shape adaptive structures combining SMA actuators produced in the form of strip with composite structures are investigated. The numerical algorithm of the 3-D SMA thermomechanical constitutive equations based on Lagoudas model is implemented to analyze the unique characteristics of SMA strip. Also, the incremental SMA constitutive equations are implemented in the user subroutine UMAT by using ABAQUS finite element program. The shape change of structure is caused by initially strained SMA strip bonded on the surface of the composite structure when thermally activated. Numerical results show that SMA strip actuator can generate enough recovery force to deform the composite structure and sustain the deformed shape subjected to large external load, simultaneously.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1996년도 추계학술대회 논문집
• /
• pp.391-395
• /
• 1996

This paper presents a robust force tracking control of a small-sized SMA gripper with two fingers using shape memory alloy(SMA) actuators. The mathematical governing equation of the proposed system is derived by Hamilton's principle and Lagrangian equation and then, the control system model is integrated with the first-order actuator dynamics. Uncertain system parameters such as time constant of the actuators are also included in the control model. A robust two degree of freedom(TDF) controller using H$_{\infty}$ control theory, which has inherent robustness to model uncertainties and external disturbances, is adopted to achieve end-point force tracking control of the two-finger gripper. Force tracking control performances for desired trajectories represented by sinusoidal and step functions are evaluated by undertaking both simulation and experimental works.