• Transactions of the Korean Society of Automotive Engineers
• /
• v.22 no.2
• /
• pp.141-147
• /
• 2014

This study aims to investigate the influence of bevel angles on the fatigue life of V-groove butt-welded joints with back-plates made by SM490A steel material, generally used for excavators, because changes in the geometry, material and surface properties of welded regions affect the fatigue life of welded structures. Butt type test specimens were prepared by the $CO_2$ welding of rolled steel plates (SM50A steel) with a thickness of 13.5 mm at a welding speed of 30 cm/min and these Butt type test specimens had two different groove angles, which are $40^{\circ}$ (A type) and $30^{\circ}$ (B type). In order to investigate differences in fatigue life between two types, 4-point bending fatigue tests were conducted with a stress ratio of R=0.1 under the cyclic loading environment at a frequency of 5 Hz at room temperature. The fatigue life of A type specimens was approximately 7% higher than that of B type specimens. The stress concentration factors calculated by finite element analysis were 2.16 for A type and 2.25 for B type, whose difference was caused by the influence of the back-plates of butt-welded structures. The current results could provide important guidelines to determine the V-groove angle of butt-welded joints with a satisfactory fatigue life, although under severe operating conditions.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.6 no.3
• /
• pp.232-238
• /
• 1982

The behavior of corner crack propagation by unidirectional plane bending fatigue was investigated in the butt welded joints of SS41 and SM50 steel plates including an edge through-thickness notch. The properties of fatigue crack propagation were inspected in the weld metal, heat-affected zone, and base metal of the welded joints. Main results obtained are as follows; (1) When a plate with an edge through-thickness notch is loaded by plane bending fatigue in indirection, the 2 variant corner cracks on the upper and lower edge of the plate are initiated and propagated respectively from the notch. (2) In case of a specimen containing a corner crack, it is more reasonable to estimate the crack propagation rate by area of fracture surface than by crack surface length. (3) The rate of fatigue crack propagation becomes faster in the following order; weld metal, heat-affected zone, and base metal. (4) The specimen including reinforcement shape is rapidly failed throughout bond due to effect of its shape when the repeated load exceeds a certain cycle.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.6 no.2
• /
• pp.113-120
• /
• 1982

In the previously reported Part I, the experimental results in frictional machining that finished medium carbon steel SM 50 C under 6 kinds of liquid atmospheres by using ceramic tip as a frictional tool was described. The present study reports the experimental results that all the machining conditions are same in the Part I except tool material changed ceramics into tungsten carbide. The ceramic tool material is a stable oxide and a non-metallic material, but the tungsten carbide has the metallic characteristics that adhere to carbon steel at about 750.deg.C. The present study shows th comparison of the experimental results for the above 2 kinds of frictional tool material.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.11 no.5
• /
• pp.762-771
• /
• 1987

Friction welding is a fusion process in which the necessary heat is generated by clamping one of the two pieces to be welded in a stationary chuck and rotating the other at high speed with an axially applied load. It is essentially a variation of the pressure welding process but utilizes a novel heating method. In addition to the foregoing advantages, it has also been reported excellent for welding dissimilar materials. Therefore, this study reported on investigating the strength behavior for the frictionally welded domestic structural steel SM45C and SUS304. The results obtained by the experiments are as follows. (1) The highest tensile strength of the best friction welded specimen (B4) is about 3% lower than that of SM-45C base metal, and 9% lower than that of SUS304 base metal. The heat treated specimens (850.deg.C 1hr A.C) have almost same value of tensile strength. (2) The strain of SM45C base metal is 27.3% and that of SUS304 is 42%, that of the best friction welded specimen (B4) appeared as 11.9% which is about 50% lower than the base metal, so, this same phenomenon apeared in all the other welding conditions. (3) The bending strength of SM45C base metal is 123kgf/mm$^{2}$ and that of SUS304 is 127kgf/mm$^{2}$. The best specimen (B4) appeared as 121kgf/mm$^{2}$ which is almost same bending strength for both base metals. (4) The friction welded condition involving maximum strength is determined by P$_{1}$=8kgf/mm$_{2}$, P$_{2}$=22kgf/mm$_{2}$, T$_{1}$=10sec, T$_{2}$=2sec, and amount of upset 7.6mm. (5) The interface of two dissimilar materials are mixed strongly, and welded zone is about 1.03mm and also the heat affected zone is about 2.36mm at SM45C while about 1.85mm at SUS304, therefore the welded zone and heat affected zone are very narrow to compare with those of the other welding materials.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.9 no.3
• /
• pp.69-75
• /
• 2000

The object of the research is to estimate for pearlite structure of quenched carbon steels. The effects of temperature on physical properties metallic structures and the latent heat by phase transformation were considered. In this study a set of constitutive equations relevant to the analysis of thermo-elasto plastic materials with pearlite phase transformation during quenching process way presented on the basis of continuum thermo-dynamics. The iso-thermal transformation curve of the SM50C was formlated by cubic spline curve. The formulated equations of evolution in pearlite transformation was used for structure analysis. The volume fraction of pearlite was obtained from the results of calculated metallic structure by Finite element equation.

• Journal of Environmental Health Sciences
• /
• v.47 no.3
• /
• pp.259-266
• /
• 2021

Objectives: This study was conducted to identify the emissions characteristics of total particulate matter (TPM), fine dust (PM₁₀, PM_2.5), and gaseous pollutants (SOx, NOx) in iron and steel manufacturing facilities in order to investigate emissions factors suitable for domestic conditions. Methods: Total particulate matter (TPM), fine dust (PM₁₀, PM_2.5), and gas phase materials were investigated at the outlet of electric arc furnace facilities using a cyclone sampling machine and a gas analyzer. Results: The concentrations of TPM ranged from 1.64 to 3.14 mg/Sm³ and the average was 2.47 mg/Sm³. Particulate matter 10 (PM₁₀) averaged 1.49 mg/Sm³ with a range of 0.92 to 1.99 mg/Sm³, and the resulting ratio of PM₁₀ to TPM was around 60 percent. PM_2.5/PM₁₀ ranged from 33.7 to 47.9% and averaged 41.6%. Sulfur oxides (SOx) were not detected, and nitrogen oxides (NOx) averaged 6.8 ppm in the range of 5.50 to 8.67 ppm. TPM emission coefficients per product output were in the range of 0.60 to 1.26 g/kg, 0.13 to 0.79 g/kg for PM₁₀ and 0.12 to 0.36 g/kg for PM_2.5, and showed many differences from the emissions coefficients previously announced. An emissions coefficient for NOx is not currently included in the domestic notices, but the results were calculated to be 0.42 g/kg per product output. Conclusions: Investigation and research on emissions coefficients that can reflect the characteristics of various facilities in Korea should be conducted continuously, and the determination and application of unique emissions coefficients that are more suitable for domestic conditions are needed.

• Journal of the Korean Society of Industry Convergence
• /
• v.26 no.2_2
• /
• pp.341-347
• /
• 2023

The subway is one of the most common and important means of transportation in modern society. In order to use the subway safely, tracks are necessary, but trains are prone to derailment and collisions. In order for the train to run safely on the track, the fishplate that connects the line connection is used. The damaged railway was a fishplate for connecting subway lines used for 11 years, and damage analysis and countermeasures were presented. Beach marks were observed on both fracture surfaces, and striations appeared at the range of crack propagation. The damaged part is Cr carbide, which has a higher hardness than the base metal, and is judged to be embrittled and destroyed by fatigue. The SM50C fishplate was subjected to a cyclic stress of about 59% of the upper limit of tensile-compression fatigue limit, but inclusions were the cause of failure. In order to prevent fatigue failure of the SM50C steel fishplate, the occurrence of inclusions should be minimized and processed to have a homogeneous structure when manufacturing the fishplate. In addition, compressive residual stress is given through surface modification such as peening to control crack generation. It is necessary to minimize the change in shape that can become a stress concentration part along with accurate fastening of the bolt, and to design the stress distribution to be as uniform as possible.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.5 no.4
• /
• pp.338-346
• /
• 1981

Honing, lapping, polishing and superfinishing are applied for a precision machining to finish the metal surface, but these precision machining are micro-cutting by hard and micro-abrasive grains. Frictional machining is the new method to finish mirrorlike surface without using those abrasive grains. The frictional machining produces high pressure and high temperature instantly by compressing a tool material against the metal surface in sliding motion. The metal surface is given plastic deformation and plastic flow by the above mentioned frictional motion, but the surface roughness of the metal surface is influenced by physical and chemical reaction in surrounding atmosphere. Therefore, the atmosphere around the metal optimum atmosphere in the frictional machining. The part 1 of the study was performed in liquid atmospheres. Diesel oil, lubricant, grease, lard oil, bean oil and cutting fluid were used as such atmospheres. Medium carbon steel SM 50 C was used as a workpiece and ceramic tip was applied as a frictional tool. The result of the experiment showed characteristic machining conditions to generate the best surface roughness in each atmospheres.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.13 no.2
• /
• pp.17-24
• /
• 2004

In end milling process, undeformed chip thickness and cutting forces vary periodically with phase change of the tool. Recently, a model has been proposed to simulate the shear and friction characteristics of an up-end milling process in terms of the equivalent oblique cutting to this. In the current study, a down-end milling process has been replaced with the equivalent oblique cutting process. And shear and tool-chip friction characteristics variation of SM45C steel has been studied using the end-mills of different helix angles. The specific shear and friction energy consumed with helix angle of $50^{\circ}$ is somewhat larger than those of$30^{\circ}$ and $40^{\circ}$. The specific shear energy consumed is about 76-77% of the specific cutting energy regardless the helix angles.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 1996.10a
• /
• pp.180-186
• /
• 1996

Using carbon steel or ceramic as a shaft material of monolithic and slited insert ring clamped on it. The fitting strengths of the sgrink fitted assemblies measured from room temperature to 30$0^{\circ}C$ and following conclusions were obtained as results of this investigation. 1) The fitting condition under which the shrink fitted assemble was stronger than that using simple fit in high temperature. 2) When both material of the 30mm-diameter shaft and 55mm-diameter boss are SM45C the clamping torque is increased 2.7times as the interference increases 3 times from 20${\mu}{\textrm}{m}$ at the contact length of 6mm monolithic fit. 3) When only the material of boss is changed to STS 304 the clamping torque is increased at the rate of 37.3N.m per 1mm increase of the contact length at the interference of 50${\mu}{\textrm}{m}$ monolithic fit.