• Korean Journal of Materials Research
• /
• v.22 no.11
• /
• pp.609-614
• /
• 2012

We report on the NO gas sensing properties of non-directional ZnO nanofibers synthesized using a typical electrospinning technique. These non-directional ZnO nanofibers were electrospun on an $SiO_2$/Si substrate from a solution containing poly vinyl alcohol (PVA) and zinc nitrate hexahydrate dissolved in distilled water. Calcination processing of the ZnO/PVA composite nanofibers resulted in a random network of polycrystalline ZnO nanofibers of 50 nm to 100 nm in diameter. The diameter of the nanofibers was found to depend primarily on the solution viscosity; a proper viscosity was maintained by adding PVA to fabricate uniform ZnO nanofibers. Microstructural measurements using scanning electron microscopy revealed that our synthesized ZnO nanofibers after calcination had coarser surface morphology than those before calcination, indicating that the calcination processing was sufficient to remove organic contents. From the gas sensing response measurements for various NO gas concentrations in dry air at several working temperatures, it was found that gas sensors based on electrospun ZnO nanofibers showed quite good responses, exhibiting a maximum sensitivity to NO gas in dry air at an operating temperature of $200^{\circ}C$. In particular, the non-directional electrospun ZnO nanofiber gas sensors were found to have a good NO gas detection limit of sub-ppm levels in dry air. These results illustrate that non-directional electrospun ZnO nanofibers are promising for use in low-cost, high-performance practical NO gas sensors.

• Journal of the Korean Magnetics Society
• /
• v.23 no.1
• /
• pp.7-11
• /
• 2013

We investigate the perpendicular magnetic anisotropy in $TiO_2$/Co/Pd on GaAs(100), MgO(100), MgO(111), Si(100), and glass substrates. We find that the roughness of $TiO_2$ depends on the $O_2$ partial pressure in the magnetron sputtering process. The perpendicular magnetic anisotropies are found in all substrates with $TiO_2$ seed layer, and the perpendicular magnetic anisotropy of Co/Pd system is insensitive on the type of the substrate when the thickness of $TiO_2$ seed layer is thicker than 5 nm. However, MgO(111) substrate promotes $TiO_2$ rutile (111) structure, and it causes largest perpendicular magnetic anisotropy in $TiO_2$/Co/Pd(111) structures.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.11 no.4
• /
• pp.47-52
• /
• 2011

Nano-scale power splitter based on Si plasmonic waveguides are designed by utilizing the multimode interference (MMI) coupler. Effective dielectric method and longitudinal modal transmission-line theory are used for simulating the light propagation and optimizing the structural parameters at 3-D guiding geometry. The designed $1{\times}2$ 50:50 MMI power splitter has a nano-scale size of only $800nm{\times}850nm$. In order to achieve a variable power splitting ratio, a $2{\times}2$ MMI coupler is designed and the corresponding power splitting ratio can be tuned in the range of 78.5%:15.5%~5.5%:86.6%. Also, it is shown that it has a large bandwidth of $1.5{\mu}m{\sim}1.7{\mu}m$. In this range, the transmission is over 0.8.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.32 no.6
• /
• pp.341-348
• /
• 2019

The purpose of this study is to model and analyze retractable large spatial structures by applying parametric modeling techniques. The modeling of wind loads in the analysis of typical structures including curved surfaces can be error-prone, and the processing time increases dramatically when there are many types of variables. However, the method based on StrAuto that was developed in previous research, facilitates the efficacious assignment of wind loads to structures and the rapid arrival of conclusions. As a result, it is possible to compare alternatives with various loads, including wind loads, to determine an optimal alternative much faster than the existing process. Further, it is almost impossible to directly input the wind load by calculating the area of an irregularly curved surface. However, the proposed method automatically assigns the wind load, which allows for automatic optimization in a structural analysis system. The approach was applied and optimized using several models, and the results are presented.

• Korean Journal of Crystallography
• /
• v.9 no.1
• /
• pp.53-63
• /
• 1998

The Cd1-xZnxS thin films were grown on the Si(100) wafers by a hot wall epitaxy method (HWE). the source and substrate temperature are 600℃ and 440℃, respectively. The crystalline structure of epilayers was investigated by double crystal X-ray diffraction (DCXD). Hall effect on the sample was measured by the van der Pauw method and the carrier density and mobility dependence of Hall characteristics on temperature was also studied. In order to explore the applicability as a photoconductive cell, we measured the sensitivity (γ), the ratio of photocurrent to darkcurrent (pc/dc), maximum allowable power dissipation (MAPD), spectral response and response time. The results indicated that the best photoconductive characteristic were observed in the Cd0.53Zn0.47S samples annealed in Cu vapor comparing with in Cd, Se, air and vacuum vapour. Then we obtained the sensitivity of 0.99, the value of pc/dc of 1.65 × 107, the MAPD of 338mW, and the rise and decay time of 9.7 ms and 9.3 ms, respectively.

• Membrane Journal
• /
• v.6 no.1
• /
• pp.44-52
• /
• 1996

For the purpose of the optimal design of a frame and plate type of pervaporation module, model equations which can predict the effects of feed flow condition on the temperature distribution of the feed developed in the module were established and the temperature distribution with feed flow condition was investigated through the model si$$\mu$ation. With increasing the Reynolds number of feed flow in the module, the flow velocity gradient in the channel height-direction as well as the volume rate of feed which acts as energy source for the evaporation of perrneants on the permeate-side surface of a membrane increased to such an extent that both mass and heat flux in the channel height direction could increase and the temperature drop of feed due to the evaporation of the permeant could be reduced correspondingly. A decrease in channel height caused the temperature drop of feed because of decreasing feed flow in the module. It was observed that the si$$\mu$ation result on the effect of Re on the temperature distribution of feed in the module has an agreement with experiment.

• Journal of the Mineralogical Society of Korea
• /
• v.6 no.1
• /
• pp.38-47
• /
• 1993

Clinoptilolite and mordenite are important constituents of the Nuldaeri Trachytic Tuff and Guryongpo Dacitic Tuff of the Tertiary Janggi Group which were deposited in a lacustrine environment. The diagenetic cystallization sequences of zeolites in different tuffaceous sediments and their chemical behaviors have been studied to know the process of their formation. The paragenetic sequence established from textural observations and chemical data : Ca-smectite ${\leftrightarrow}$(Ca, K)-clinoptilolite${\leftrightarrow}$(K, Na)-mordenite, indicates that the chemical activities of alkalic ions and Si/Al activity ratio in pore fluids changed systematically with diagenetic alteration. The chemical trend of zeolite formation is characterized by decreasing Ca and Mg, non-variable Na and increasing K in the Nuldaeri Trachytic Tuff and by decreasing Ca and Mg, non-variable Na and increasing-decreasing K in the Guryongpo Dacitic Tuff. The paragenesis from glass via smectite to alkali zeolites indicates a sequence of incongruent dissolution reactions and subsequent crystallization. Inhomogeneity in chemical composition of each zeolite may be attributed to such processes.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.06a
• /
• pp.178-178
• /
• 2007

II-VI의 넓은 밴드갭 (3.37 eV)을 가지는 ZnO는 solar cells, transparent conductive electrodes, ultraviolet light emitters, and chemical sensors 등에 응용되고 있다. 특히 고효율 ZnO계 발광 소자 구현을 위하여 MgO (7.7eV), CdO (2.0eV) 등의 고용을 통한 밴드갭을 엔지니어링 하며, 단파장 영역의 광원을 확보하기 위하여 MgO 첨가를 통한 밴드갭 에너지를 증가시키는 방향으로의 연구가 활발하다. 그러나 ZnO의 wurtzite 구조와 MgO의 rocksalt 구조의 상이한 결정구조로 인하여 Mg의 고용한계는 4 at. %, 4.1 eV 알려져 있다. 본 실험에서는 p-type Si (100), c-sapphire (0002)과 GaN 기판 위에 MgO (99.999 %)와 ZnO (99.999 %) 두가지 타겟을 사용하여 RF co-스퍼터링법으로 ZnMgO 박막을 증착 하였다. 이때 ZnO 타겟의 power 밀도는 고정 시키고 MgO 타겟의 power 밀도를 변화 시키며 Mg의 함량을 조절하여 그에 따른 광학적 구조적 특성의 변화를 연구 하였다. 성장된 ZnMgO 박막은 MgO 타겟의 power 밀도가 증가할 때 Mg의 함량이 10 at. %까지 증가 하며, 그에 따른 표면의 거칠기 및 입계 크기가 감소하며, 박막의 성장속도 또한 감소함을 SEM과 AFM을 통하여 알 수 있었다. XRD를 동하여 ZnMgO 박막의 (0002) peak의 위치는 $34.50^{\circ}{\sim}34.7^{\circ}$로 오른쪽으로 이동하며, c-축으로 성장하였음을 알 수 있다. PL과 UV룰 동하여, Mg의 함량이 증가 할수록 박막의 밴드갭 에너지는 3.2 eV에서 4.1 eV 로 증가하였다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.255-255
• /
• 2010

전하 트랩형 비휘발성 메모리는 10년 이상의 데이터 보존 능력과 빠른 쓰기/지우기 속도가 요구 된다. 그러나 두 가지 특성은 터널 산화막의 두께에 따라 서로 trade off 관계를 갖는다. 즉, 두 가지 특성을 모두 만족 시키면서 scaling down 하기는 매우 힘들다. 이것의 해결책으로 적층된 유전막을 터널 산화막으로 사용하여 쓰기/지우기 속도와 데이터 보존 특성을 만족하는 Tunnel Barrier engineered Memory (TBM)이 있다. TBM은 가운데 장벽은 높고 기판과 전극쪽의 장벽이 낮은 crested barrier type이 있으며, 이와 반대로 가운데 장벽은 낮고 기판과 전극쪽의 장벽이 높은 VARIOT barrier type이 있다. 일반적으로 유전율과 밴드갭(band gap)의 관계는 유전율이 클수록 밴드갭이 작은 특성을 갖는다. 이러한 관계로 인해 일반적으로 crested type의 터널 산화막층은 high-k/low-k/high-k의 물질로 적층되며, VARIOT type은 low-k/high-k/low-k의 물질로 적층된다. 이 형태는 밴드갭이 다른 물질을 적층했을 때 전계에 따라 터널 장벽의 변화가 민감하여 전자의 장벽 투과율이 매우 빠르게 변화하는 특징을 갖는다. 결국 전계에 민감도 향상으로 쓰기/지우기 속도가 향상되며 적층된 유전막의 물리적 두께의 증가로 인해 데이터 보존 특성 또한 향상되는 장점을 갖는다. 본 연구에서는 기존의 TBM과 다른 형태의 staggered tunnel barrier를 제안한다. staggered tunnel barrier는 heterostructure의 에너지 밴드 구조 중 하나로 밴드 line up은 두 밴드들이 같은 방향으로 shift된 형태이다. 즉, 가전자대 에너지 장벽의 minimum이 한 쪽에 생기면 전도대 에너지 장벽의 maximum은 반대쪽에 생기는 형태를 갖는다. 이러한 밴드구조를 갖는 물질을 터널 산화막층으로 하게 되면 쓰기/지우기 속도를 증가시킬 수 있으며, 데이터 보존 능력 모두 만족할 수 있어 TBM의 터널 산화막으로의 사용이 기대된다. 본 연구에서 제작한 staggered TBM소자의 터널 산화막으로는 $Si_3N_4$/HfAlO (Hf:Al=1:3)을 사용하여 I-V(current-voltage), Retention, Endurance를 측정하여 메모리 소자로서의 특성을 분석하였으며, 터널 산화막의 제 1층인 $Si_3N_4$의 두께를 1.5 nm, 3 nm일 때의 특성을 비교 분석하였다.

• Korean Journal of Materials Research
• /
• v.9 no.3
• /
• pp.257-262
• /
• 1999

The selective area growth of GaN by metal organic chemical vapor deposition has been carried out on GaN/ sapphire substrate using $SiO_2$ mask. We investgated the effect of growth parameters such as flow rate of $NH_3$(500­~1300sccm) and the growth temperature(TEX>$950~1060^{\circ}C$) on the growth selectivity and characteristics of GaN using the Scanning Electron Microscopy(SEM). The selectivity of GaN improved as flow rate of NH, and growth temperature in­creased. But the grown GaN shapes on the substrate windows was independent of the flow rate of $NH_3$. On the pattern shapes such as circle, stripe, and radiational pattern(rotate the stripe pattern by $30^{\circ}, 45^{\circ}$), we observed the hexagonal pyramid, the lateral over growth on the mask layer, and the difference of the lateral growth rate depending on growth condition.