• Nuclear Engineering and Technology
• /
• 제52권6호
• /
• pp.1304-1317
• /
• 2020

The tubes in a heat exchanger, such as a steam generator (SG), are subjected to crossflow, and interaction between tubes and supports can happen, which can cause fretting wear of tubes. Although many experiments and models have been established, some detailed mechanisms are still not sufficiently clear. In this work, more attention is paid to obtain the regulation of impact and sliding in the complex process and many factors, such as excitation forces and clearances. The responses and contact forces were analyzed to obtain clear understanding of the influences of these factors. Room temperature tests in the air were established. The results show that the effect of clearance on the normal work rate is not monotonous and instead has two peaks. The force ratio can influence the normal work rate by changing the distribution of contact angles, which can result in higher sliding in the contact process. Fretting wear tests are conducted, and the wear surfaces are analyzed by a scanning electron microscope (SEM) and energy dispersive X-ray spectrometer (EDX). The results of this work can serve as a reference for impactsliding contact analysis between AVBs and tubes in steam generators.

• 한국환경과학회지
• /
• 제23권6호
• /
• pp.1175-1182
• /
• 2014

In this study, we examined the effect of cathode from electrolysis reactor for treating ballast water. We are going to select a suitable cathode for seawater electrolysis after considering the effect on the generation of the oxidant of cathode and the electrode deposition materials adhering to the surface of cathode. Anode is Ru-Ti-Pd electrode and cathode are Ti, Pt, JP520 (Ni-Pt-Ce) electrodes. Using the cathode of the three types, experiments were conducted to examine the effects of TRO (total residual oxidants) generation concentration and RNO (N, N-Dimethyl-4-nitrosoaniline, indicator of the generation of OH radical) degradation concentration (in 1, 35 psu), ohmic drop, FESEM(field emission scanning electron microscope) observation of cathode surface and EDX (energy dispersive X-ray spectroscopy) measurements of attached fouling material. The results showed that TRO generation concentration and RNO degradation concentration in according to each type of cathode are not different. The attached fouling materials were observed on the surface of Ti and the JP520 electrode by the observation of SEM after electrolysis for two hours, but it was not observed on the surface of Pt electrode. When considering the surface ohmic drop of cathode and the attached fouling materials, Pt electrode was judged as the excellent cathode.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2004년도 추계학술대회 논문집 Vol.17
• /
• pp.683-686
• /
• 2004

In recent years, the supercapacitor and hybrid capacitor have related with substitutional energy source focused of many scientists because of their usage in power sources for electric vehicles, computers and other electric devices. The storage energy of electrical charge is based on electrostatic interactions in the electric double layer at the electrode/electrolyte interface, resulting in high rate capability and long cycle performance compared with batteries based on Faradaic electrode reactions. So we have been considered to carbon nanofibers as the ideal material for supercapacitors due to their high utilization of specific surface area, good conductivity, chemical stability and other advantages. In this work, we aimed to find out that the capacitance have increased because of electrochemical capacitance to provide by carbon nanofibers. Also carbon nanofibers based on chemical method and water treatment have been resulted larger capacitances and also exhibit better electrochemical behaviors about 15% than before of nontreated state. And also optical observations with treated and nontrteated carbon nanofibers discussed by the TEM, SEM, EDX, BET works and specific surface area analyzer. Their results also focused on the surface area of electrode and electrical capacitance was also improved by the effect of surface treatments.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2004년도 하계학술대회 논문집 Vol.5 No.2
• /
• pp.898-901
• /
• 2004

[ $ZnCr_2O_4$ ]를 모물질로 하고 MgO, $TiO_2$를 몰비로 2:1, 4:1, 6:1, 및 8:1이 되게 정량적으로 조합한 후, 조사하였다. $ZnCr_2O_4$-MgO와 $ZnCr_2O_4-TiO_2$를 X-선 분석한 결과 Spinel 결정구조를 형성하였으며, 또한 SEM과 EDX 분석결과 각각 $Li_2CrO_4$와 $Li_3VO_4$의 형성으로 인하여 저항 특성이 나타나는 것을 알 수 있었다. $ZnCr_2O_4-MgO$, $ZnCr_2O_4-TiO_2$에서 MgO의 양이 증가할수록 저항값은 약간 감소하는 반면, $TiO_2$의 양이 증가할수록 저항값이 급격히 증가하는 특성을 나타내었고, 감습 특성에서도 M??보다 TiO2가 더 높게 나타내었다. 습에 따른 복원 특성의 경우 $700^{\circ}C$에서 소결한 ($ZnCr_2O_4:MgO=4:1$)과 ($ZnCr_2O_4:TiO_2=6:1$) 조성의 센서가 가장 양호하였다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2008년도 추계학술대회 논문집 Vol.21
• /
• pp.112-112
• /
• 2008

박막형 태양전지에 관한 연구는 1954년 D.C. Reynolds 가 단결정 CdS 에서 광기전력을 발견하면서부터 시작되었다. 고효율 단결정 규소 태양전지가 간편하게 제작되고 박막형 태양전지의 수명문제가 대두되어 한때는 연구가 중단되어지기도 하였으나, 에너지 문제가 심각해지면서 값이 저렴하고 넓은 면적에 쉽게 실용화 할 수 있는 박막형 태양전지에 많은 관심을 가지게 되었다. 박막형 태양전지에 사용되는 CdS는 II-VI 족 화합물 반도체로서 에너지금지대폭이 2.42eV인 직접천이형 n-type 반도체로서 대부분의 태양광을 통과시킬 수 있으며 가시광선을 잘 투과시키고 낮은 비저항으로서 광흡수층인 CdTe/$CuInSe_2$ 등과 같이 태양전지의 광투과층(윈도레이어)으로 널리 사용되고 있다. 이러한 이종접합 박막형 태양전지의 효율을 높이기 위해선 윈도레이어 재료인 CdS 박막의 낮은 전기 비저항치와 높은 광 투과도 값이 요구되어지고 있다. CdS 박막의 제작방법으로는 spray pyrolysis법, 스크린프린팅, 소결법, puttering법, 전착법, CBD(chemical bath deposition)법 및 진공증착법 등의 여러 가지 방법들이 보고되었다. 이 중 sputtering의 경우, 다른 방법들에서는 얻기 어려운 매우 얇은 두께의 박막 증착이 가능하며, 균일성 또한 우수하다. 또한 대면적화가 용이하여 양산화 기술로는 다른 제조 방법들에 비해 많은 장점을 가지고 있다. 따라서 본 연구에서는 sputtering에 의해 증착한 CdS의 박막에 광투과도 등의 향상을 위하여 CMP( chemical mechanical polishing) 공정을 적용하여 표면 특성을 개선하고자 하였다. 그 기초적인 자료로서 CdS 박막의 CMP 공정 조건에 따른 연마율과 비균일도, 표면 특성 등을 ellipsometer, AFM(atomic force microscopy) 및 SEM(scanning electron microscope) 등을 활용 하여 분석하였다.

• Journal of Periodontal and Implant Science
• /
• 제34권1호
• /
• pp.1-17
• /
• 2004

It is improtant that performing prophylaxis procedure on an infected implant surface in order to treat peri-implantitis should not change the surface roughness and composition, so that the surface can be recovered to almost same condition as initial implant surface. This thesis, therefore, studied an effect of various oral hygiene instrument on implant surface. A surface roughness measurement instrument and an infection electron microscope were used to observe a change on surface. The purpose of this study was to obtain a clinical guidelines during implant care and peri-implantitis treatment. The result were as follows 1. Ra values (surface roughness value) at experimental group 1, group 2, and group 5 were increased significantly as compared with comparison group(p<0.05). 2. When compared experimental group 1 with each experimental groups at which prohylaxis procedure was performed, mean values of Ra at experimental group 2, group 3, group 6, and group 7 were decreased significantly(p<0.05). 3. Mean value of Ra was lowest at experimental group 2, and highest at experimental group 2, and highest at experimental group 5. 4. Analysis of SEM showed that was significant surface change at experimental group 2, group 3, group 4, group 5, and group 6 as compared with comparison group(X1000). 5. Analysis fo EDX showed that a quantity of Ti on surface for experimental group 6 was very similar to that for comparison group. In conclusion, air-powder abrasive and citric acid, plastic instrument are safe methods to use for performing prophylaxis procedure on implant care or for cleaning and sterilization process on treatment of peri-implantitis, based on the result that those method did not affect implant surface roughness and Ti composition.

• 한국작물학회지
• /
• 제47권3호
• /
• pp.161-166
• /
• 2002

인삼 뿌리에 발생하는 적변현상을 구명하기 위하여 적변삼표피의 형태적 특성, 세균의 밀도 및 무기물 함량의 변화를 조사한 결과, 다음과 같은 결론을 얻었다. 1. 적변삼의 표피는 건전삼에 비하여 두꺼웠으며, 세포벽이 분해되어 심하게 파괴되어 있었다. 그러나 건전삼의 경우에는 세포가 장방형의 일정한 형태를 유지하고 조직의 파괴도 전혀 발생하지 않았다. 2. 파괴된 적변삼의 표피조직에는 막대모양의 세균이 다수 존재하였으며, 세균밀도는 2.9$\times$$10^{6}$-3.5$\times$$10^{7}$ CFU/g(fresh weight)으로 많은 세균이 분리되었다. 건전삼표피조직에서는 세균이 거의 관찰되지 않았으나, 세균밀도는 4.7$\times$$10^2$-1.2$\times$$10^3$ CFU/g(fresh weight)으로 적변삼에 비하여 매우 낮게 나타났다. 3. 인공적으로 분리세균을 접종하여 적변을 유발시킨 표피조직에서도 자연발생 적변삼에서와 동일한 표피조직의 파괴양상을 보였으며, 다수의 세균이 관찰되었다. 4. 적변삼의 표피조직에서는 Al, Si 및 Fe의 함량이 높았으나, 건전삼에서는 K의 함량이 높게 나타나 적변현상의 발생은 표피조직에서 무기물 함량의 변화를 유발하였다

• Archives of Plastic Surgery
• /
• 제33권3호
• /
• pp.324-329
• /
• 2006

The silicone rubber implants are widely used in plastic surgery because of various advantages; however, calcification in surface of implant(as a chemical resistance) may transform or destroy the high molecular biomaterial when it stays too long within the human body. The purpose of this study is to determine the relationship between calcification and the histological disparities of the tissues surrounding the area adjoining the silicone nasal implant by examining the regional characteristics of calcium deposits in the silicone nasal implant via elemental analyses using EDX(energy-dispersive X-ray analysis) and ultrastructural analyses using SEM(scanning electron microscopy). The subjects of the study were 19 silicone nasal implants removed by revision rhinoplasty, all displaying calcification. According to the tissue characters, the implant surface was divided into 4 zones with the rhinion as the basis. For each zone, elemental and ultrastructural analyses were performed. Elemental analysis revealed that the calcium deposits consisted of Ca and P only. There were no statistically significant disparities among the ratios between Ca and P according to the zones. Ultrastructural analysis showed acellular mineral-like deposits coalesced to create amorphous deposits in all zones; however, in zones 1 and 3(more pressurized zones by periosteum or nasal bone), additional flaky cylinder-shaped calcium deposits were detected. Thus, it seems that the histological disparities in the surrounding tissues do not affect the components and their proportions in the calcification process. However, it can be inferred that the physical environment due to the histological disparities in the surrounding tissues affects the ultrastructures of calcium deposits.

• 한국포장학회지
• /
• 제4권2호
• /
• pp.24-32
• /
• 1998

인쇄하지 않은 복사용지에 대해 침지, 탈수, 건조등 일련의 리사이클링 사이클의 반복횟수에 따라 얻어지는 재생지의 광학적 성질의 변화와, 리사이클링 횟수를 달리한 펄프를 이용하여 고지를 제조한 후 하여 고지의 탈묵성 변화를 살펴보았다. 그 결과, 리사이클링 횟수 증가에 따라 얻어진 재생지의 백색도는 원래보다 약10% 저하되었으나, 섬유간 결합감소에 따른 비산란계수의 증가로 불투명도는 약10%정도 증가하는 경향을 보였다. 또한, 리사이클링 횟수에 따른 고지의 탈묵성은 섬유의 표면 자유에너지 감소, 즉 섬유의 소수화 증가로 인하여 약간 저하되는 것으로 나타났다.

• 상하수도학회지
• /
• 제25권3호
• /
• pp.285-291
• /
• 2011

Membrane fouling is an unavoidable phenomenon and major obstacle in the economic and efficient operation under sea water reverse osmosis (SWRO). When fouling occurs on the membrane surface, the permeate quantity and quality decrease, the trans-membrane pressure (TMP) and operation costs increase, and the membrane may be damaged. Therefore, chemical cleaning process is important to prevent permeate flow from decreasing in RO membrane filtration process. This study focused on proper chemical cleaning condition for Shuaibah RO plant in Saudi Arabia. Several chemical agents were used for chemical cleaning at different contact time and concentrations of chemicals. Also autopsy analysis was performed using LOI, FT-IR, FEEM, SEM and EDX for assessment of fouling. Specially, FEEM analysis method was thought as analyzing and evaluating tool available for selection of the first applied chemical cleaning dose to predict potential organic fouling. Also, cleaning time should be considered by the condition of RO membrane process since the cleaning time depends on the membrane fouling rate. If the fouling exceeds chemical cleaning guideline, to perfectly remove the fouling, certainly, the chemical cleaning is increased with membrane fouling rate influenced by raw water properties, pre-treatment condition and the point of the chemical cleaning operation time. Also choice of cleaning chemicals applied firstly is important.