• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1996.11a
• /
• pp.40-43
• /
• 1996

Substrates of SAW filter are mainly single crystal such as LiNbO$_3$, LiTaO$_3$. However, fabrication of crystal is difficult and cost is very high. In this study, crystal was substituted for piezoelectric ceramics which has simple fabrication process. The same SAW filter mask was photolithographed on crystal(LiNbO$_3$) substrate and ceramic(PZT4, PZT5A and PZT8) substrate in order to compare experimental value with theoretical value. The difference of center frequency was only 3.7%. PZT8 showed good bandwidth properties. It is considered that PZT8 has higher mechanical quality factor and propagation velocity than PZT4, PTT5A.

• Proceedings of the KIEE Conference
• /
• 1994.07b
• /
• pp.1457-1459
• /
• 1994

A surface acoustic wave(SAW) sensor for the detection of odorants has been constructed by depositing various phospholipids and fatty acids onto the surface of the SAW device. Applying the Langmuir-Blodgett technique, it was possible to deposit the optimal number of layers which was found to be between 10 and 20. Menthone, amylacetate, acetoin, and other organic gases showed different affinities to the coated lipids. An explanation is given for different odorant affinities based on the monolayer properties of phospholipids.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1999.11a
• /
• pp.151-154
• /
• 1999

ZnO thin films on glass substrate were deposited by RF magnetron reactive sputter with various argodoxygen gas ratios and substrate temperatures. Crystallinities, surface morphologies, chemical compositions, and electrical properties of the films were investigated by XRD, SEM, XPS and electrometer(keith1ey 617). All films showed a strong prefered orientation along the c-axis on glass substrate, and the chemical stoichiometry was obtained at Ar/$O_2$=50/50. The propagation velocity of ZnO SAW filter was about 2, 590 dsec and insertion loss was a minimum value of about -21dB.

• Special Issue of the Society of Naval Architects of Korea
• /
• 2007.09a
• /
• pp.118-127
• /
• 2007

SAW(Submerged Arc Welding) process is generally applied to a wide range of welding area in the fabrication of steel structure. This process has a good characteristic properties such as the high quality of welds and the high deposition rates, but in case of welding on a thick steel plate, it also has higher cold crack susceptibility than that of a thin steel plate. The purpose of this research is to find the main factor of crack generation and clarify the countermeasure for crack prevention, and then establish the optimum welding condition in a heavy thick steel plate. The results of this study are as follows, 1. The cause of crack generation is found the diffusible hydrogen penetrated into weld metal by decomposition of the remained moisture in SAW flux during welding. 2. For the removal of diffusible hydrogen, the raw materials of SAW flux are to be dehydrated at the high temperature in the initial manufacturing stage. 3. Mechanical properties of weld metal welded with the dehydrated SAW flux were evaluated very excellent, furthermore the weld metal has been proved to have low diffusible hydrogen content with 3.1ml /100g. 4. The weldability and quality welded with thick steel plates were improved by establishing the new optimum welding condition.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.31 no.11A
• /
• pp.1159-1166
• /
• 2006

In this paper, we have designed a RFID reader receiver system for improving the performance of the passive Tag based 9$'908.5{\sim}914MHz'$ RFID reader, and analyzed the system performance according to the frequency, the reader, and tag properties. The commercial receive system causes a loss in sensitivity because of 24 capacitors and 6 inductors. So we have designed an improved system using a circulator, LNA and a SAW filter. The experimental results show that the use of a circulator to separate the Tx/Rx paths eliminates interference, the LNA improves the sensitivity of the Rx module and SAW filter eliminates the noise and spurious components in the received signal.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.52 no.7
• /
• pp.288-292
• /
• 2003

AlM thin film has been deposited on A1$_2$O$_3$ substrate by reactive radio frequency(RF) magnetron sputtering method under various operating conditions such as working pressure, fraction of nitrogen partial pressure, and substrate temperature. Scanning Electron Microscope(SEM), X-ray Diffraction(XRD), and Atomic Force Microscope(AFM) have been measured to find out structural properties and preferred orientation of AlN thin films. SAW velocity of IDTs/AlN/Si structure was about 5038［㎧］ at the center frequency of 251.9［MHz］ and insertion loss was measured to be relatively low value of 35.6［dB］. SAW velocity of IDTs/AlN/A1$_2$O$_3$ structure was improved to be about 5960［㎧］ at the center frequency of 296.7［MHz］.

• Proceedings of the Acoustical Society of Korea Conference
• /
• 1993.06a
• /
• pp.155-158
• /
• 1993

• The Korean Journal of Ceramics
• /
• v.3 no.2
• /
• pp.110-115
• /
• 1997

Li-doped ZnO films were prepared on Corning 1737 glass substrate by an rf magnetron sputtering technique using ZnO targets with various $Li_2CO_3$ contents ranging from 0 to 10 mol%. The effects of Li doping on the crystallinity and electrical properties of ZnO films were studied for their SAW filter applications. The film resistivity largely increased without suppressing the c-axis orientation and crystallinity with a small addition of Li. Heat treatment of the film at 40$0^{\circ}C$ induced that the film resistivity, c-axis orientation and crystallinity slightly increased. However, heat treatment of the film at 50$0^{\circ}C$ resulted in much lower resistivity than that of as-deposited film due to the increase of electron concentration caused by the evaporationof Li atoms from the ZnO film. Large addition of Li into the ZnO film rather diminished the film resistivity and suppressed the c-axis growth. It was concluded that a small doping of Li into the ZnO film and heat treatment at 40$0^{\circ}C$ caused the film resistivity to be high enough for SAW filter applications without suppression of the c-axis orientation and crystallinity.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2006.05a
• /
• pp.105-106
• /
• 2006

The creep properties have been evaluated for type 316LN stainless steel welded by the SAW method. The creep tests were conducted with different stress levels for both the base and weld metals at $550^{\circ}C\;and\;600^{\circ}C$. The results of the creep-rupture time of the weld metal did not show a large difference when compared to those of the base one, though it exhibited a little lower value at $600^{\circ}C$. The creep rate of the weld metal was lower than that of the base one at the same stress and rupture-time conditions. The creep-rupture ductility of the weld metal is found to be decreased by about 60%, compared to the base one. This is due to the decreasing of tensile elongation and the increasing of the yield stress in the weld metals.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.11a
• /
• pp.251-252
• /
• 2006

A development of surface acoustic wave gas sensor to detecting volatile gas has been observed by monitoring output signal as function of time onto the network analyzer. The SAW sensor with a center frequency of 200MHz was fabricated on $42^{\circ}$ S-T Quartz substrates. Using the gas chromatography column has been selectivity. Experimental results, which show the phase change of output signal under the absorption of volatile gas onto sensors, were presented. The proposed sensor has the properties of high sensitivity compare to the conventional SAW gas sensor and chemical selectivity. Thus, it is thought these results are applicable for use in sensor array of an high performance electronic nose system.