• 소성∙가공
• /
• 제6권3호
• /
• pp.239-249
• /
• 1997

The behaviour of alloys in the semi-solid state strongly depends on the imposed stress state and on the morphology of the phase which can vary from dendritic to globular. To optimal net shape forging of semi-solid materials, it is important to investigate for filling phenomena in forging process of arbitrarily shaped dies. To produce a automotive part which has good mechanical property, the filling pattern according to die velocity and solid fraction distribution has to be estimated for arbitrarily shaped dies. Therefore, the estimation of filling characteristic in the forging simulation with arbitrarily shaped dies of semi-solid materials are calculated by finite element method with proposed algorithm. The proposed theoretical model and a various boundary conditions for arbitrarily shaped dies is investigated with the coupling calculation between the liquid phase flow and the solid phase deformation. The simulation process with arbitrarily shaped dies is performed to the isothermal conditions of two dimensional problems. To analysis of forging process by using semi-solid materials, a new stress-strain relationship is described, and forging analysis is performed by viscoelastic model for the solid phase and the Darcy's law for the liquid flow. The calculated results for forging force and filling limitations will be compared to experimental data. The filling simulation of simple products performed with the uniform billet temperature(584$^{\circ}C$) from the induction heating by the commercial package MAGMAsoft. The initial step of computation is the touching of semi-solid material with the end of die gate and the initial concept of proposed system just fit with the capability of MAGMAsoft.

• KSBB Journal
• /
• 제18권4호
• /
• pp.266-271
• /
• 2003

아직 국내에서는 드물게 경작되고 있지만 이미 옛 고서적에 나와 있는 초석잠 (Stachys sieboldii MIQ.)에는 많은 유용한 물질이 있음을 알 수 있었다. 줄기의 메탄을 추출물 100 mg을 메탄을 20 mL에 녹여 만든 샘플에서 total poplyphenol과 flavonoid가 각각 9.33 $\mu\textrm{g}$/mL (1.97%), 3.77 $\mu\textrm{g}$/mL (0.75%)씩 함유되고 있음을 알 수 있으며 각 유기 용매층의 추출물의 항산화 활성도를 비교해 본 결과 DPPH법을 통해 기존의 항산화제인 $\alpha$-tocopherol (21.8 $\mu\textrm{g}$), BHT (100 $\mu\textrm{g}$) 그리고 BHA (20.6 $\mu\textrm{g}$)와 비교해도 에틸아세테이트 (15 $\mu\textrm{g}$), 부탄올 (50 $\mu\textrm{g}$) 추출물의 항산화능이 뒤지지 않음을 알 수 있었다. 또한 과산화 지질 형성 억제능과 아질산염 소거능 조사에서 에틸아세테이트의 추출물이 가장 높은 활성도를 나타내었으며 기존의 항산화제들과 비슷한 효능을 나타내었다. 이를 실리카겔 칼럼 크로마토그래피를 이용해 다시 분획하였고 UV/VIS 흡광광도계를 통해 최대 흡광도의 파장은 280-330 nm 사이에 나타내었다. 그 중 최대 흡광도가 284 nm인 ES-1에서 가장 높은 항산화 활성을 보였다. 이는 일반적으로 알려져 있는 phenolic compounds의 UV-VIS spectral data와 일치하며 다양한 phenolic compounds가 초석잠 (Stachys sieboldii MIQ.) 속에 함유되어 있음을 알 수 있었다.

• 한국전산구조공학회논문집
• /
• 제22권4호
• /
• pp.343-348
• /
• 2009

본 연구에서는 분자동역학 전산모사와 미시역학 모델을 이용하여 나노입자의 체적분율이 높은 경우 나노 입자의 크기효과와 체적분율 효과가 나노복합재의 기계적 물성에 미치는 영향을 효과적으로 묘사할 수 있는 순차적 브리징 해석기법을 제안하였다. 체적분율이 12%로 고정된 상태에서 나노입자의 크기변화에 따른 영률과 전단계수를 분자동역학 전산모사를 통해 예측한 후, 이를 연속체 모델에서 구현하기 위해 다중입자모델을 적용하였다. 나노입자의 크기효과를 반영하기 위해 입자와 기지 사이에 유효계면을 추가적인 상으로 도입하였고, 12%의 체적분율 조건에서 나타날 수 있는 체적분율 효과는 나노복합재를 둘러싸는 가상의 영역인 무한영역의 물성값의 변화를 통해 조절되도록 하였다. 유효계면과 무한영역의 물성을 입자의 반경에 대한 함수로 근사한 후 다양한 입자의 크기에서 나타나는 나노복합재의 물성변화의 예측이 가능하도록 하였다. 제안된 브리징 해석기법의 적용을 통해 분자동역학 해석결과와 잘 일치하는 결과를 연속체 모델에서 효율적이고 정확하게 얻을 수 있었다. 또한 유효계면의 두께와 물성 변화가 나노복합재의 기계적 물성에 미치는 영향을 고찰하였다.

• Steel and Composite Structures
• /
• 재36권6호
• /
• pp.671-687
• /
• 2020

The aim of this research is to analyze buckling and bending behavior of a sandwich Reddy beam with porous core and composite face sheets reinforced by boron nitride nanotubes (BNNTs) and shape memory alloy (SMA) wires resting on Vlasov's foundation. To this end, first, displacement field's equations are written based on the higher-order shear deformation theory (HSDT). And also, to model the SMA wire properties, constitutive equation of Brinson is used. Then, by utilizing the principle of minimum potential energy, the governing equations are derived and also, Navier's analytical solution is applied to solve the governing equations of the sandwich beam. The effect of some important parameters such as SMA temperature, the volume fraction of SMA, the coefficient of porosity, different patterns of BNNTs and porous distributions on the behavior of buckling and bending of the sandwich beam are investigated. The obtained results show that when SMA wires are in martensite phase, the maximum deflection of the sandwich beam decreases and the critical buckling load increases significantly. Furthermore, the porosity coefficient plays an important role in the maximum deflection and the critical buckling load. It is concluded that increasing porosity coefficient, regardless of porous distribution, leads to an increase in the critical buckling load and a decrease in the maximum deflection of the sandwich beam.

• International Journal of Naval Architecture and Ocean Engineering
• /
• 제8권6호
• /
• pp.589-601
• /
• 2016

The hybrid grid was adopted and numerical prediction analysis of propeller unsteady bearing force considering free surface was performed for mode and full-scale KCS hull-propeller-rudder system by employing RANS method and VOF model. In order to obtain the propeller velocity under self-propulsion point, firstly, the numerical simulation for self-propulsion test of full-scale ship is carried out. The results show that the scale effect of velocity at self-propulsion point and wake fraction is obvious. Then, the transient two-phase flow calculations are performed for model and full-scale KCS hull-propeller-rudder systems. According to the monitoring data, it is found that the propeller unsteady bearing force is fluctuating periodically over time and full-scale propeller's time-average value is smaller than model-scale's. The frequency spectrum curves are also provided after fast Fourier transform. By analyzing the frequency spectrum data, it is easy to summarize that each component of the propeller bearing force have the same fluctuation frequency and the peak in BFP is maximum. What's more, each component of full-scale bearing force's fluctuation value is bigger than model-scale's except the bending moment coefficient about the Y-axis.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2003년도 하계학술대회 논문집 Vol.4 No.2
• /
• pp.1034-1037
• /
• 2003

Microcrystalline silicon(c-Si:H) thin-film solar cells are prepared with intrinsic Si-layer by hot wire CVD. The operating parameters of solar cells are strongly affected by the filament temperature ($T_f$) during intrinsic layer. Jsc and efficiency abruptly decreases with elevated $T_f$ to $1400^{\circ}C$. This deterioration of solar cell parameters are resulted from increase of crystalline volume fraction and corresponding defect density at high $T_f$. The heater temperature ($T_h$) are also critical parameter that controls device operations. Solar cells prepared at low $T_h$ ($<200^{\circ}C$) shows a similar operating properties with devices prepared at high $T_f$, i.e. low Jsc, Voc and efficiency. The origins for this result, however, are different with that of inferior device performances at high $T_f$. In addition the phase transition of the silicon films occurs at different silane concentration (SC) by varying filament temperature, by which highest efficiency with SC varies with $T_f$.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2003년도 하계학술대회 논문집 C
• /
• pp.1598-1600
• /
• 2003

Microcrystalline silicon(c-Si:H) thin-film solar cells are prepared with intrinsic Si-layer by hot wire CVD. The operating parameters of solar cells are strongly affected by the filament temperature ($T_f$) during intrinsic layer. Jsc and efficiency abruptly decreases with elevated $T_f$ to $1400^{\circ}C$. This deterioration of solar cell parameters are resulted from increase of crystalline volume fraction and corresponding defect density at high $T_f$ The heater temperature ($T_h$) are also critical parameter that controls device operations. Solar cells prepared at low $T_h$ (<$200^{\circ}C$) shows a similar operating properties with devices prepared at high $T_f$, i.e. low Jsc, Voc and efficiency. The origins for this result, however, are different with that of inferior device performances at high $T_f$. In addition the phase transition of the silicon films occurs at different silane concentration (SC) by varying filament temperature, by which highest efficiency with SC vanes with $T_f$.

• 대한기계학회논문집B
• /
• 제37권5호
• /
• pp.513-522
• /
• 2013

본 연구에서는 다중효용 증발식 담수기에 쓰이는 강하막식 증발기의 수치해석을 수행하였다. 증발기에 사용되는 다관군을 다공성 매질로 묘사하고 공간평균 개념을 적용하였다. 증발기 내부의 유동계산 및 열 전달로 인한 상변화를 계산하기 위해서 FLUENT 와 UDF 가 사용되었다. 작동조건에 대한 증발기의 성능변화를 살펴보기 위해 수평관 내 증기 질량 유속을 $0.5{\sim}2.5kg/m^2s$, 관내입구 측 비 응축성 기체의 질량분율을 0~1%, 그리고 수평관 외 뿌려지는 강하막의 액막 레이놀즈 수를 100~1000 으로 바꾸어가며 해석을 수행하였다. 관내 증기유속 및 관외 강하막 레이놀즈 수가 증가할수록 증발량은 증가하였으며, 관내 비 응축성 기체의 질량분율이 1%증가함에 따라 증발량이 0.87%줄어들었다.

• 대한조선학회논문집
• /
• 제50권2호
• /
• pp.79-87
• /
• 2013

In this paper, an Euler equation solver based on a Cartesian-grid method and non-uniform staggered grid system is applied to predict the ship motion response and added resistance in waves. Water, air, and solid domains are identified by a volume-fraction function for each phase and in each cell. For capturing the interface between air and water, the tangent of hyperbola for interface capturing (THINC) scheme is used with a weighed line interface calculation (WLIC) method. The volume fraction of solid body embedded in a Cartesian-grid system is calculated by a level-set based algorithm, and the body boundary condition is imposed by volume weighted formula. Added resistance is calculated by direct pressure integration on the ship surface. Numerical simulations for a Wigley III hull and an S175 containership in regular waves have been carried out to validate the newly developed code, and the ship motion responses and added resistances are compared with experimental data. For S175 containership, grid convergence test has been conducted to investigate the sensitivity of grid spacing on the motion responses and added resistances.

• 한국식품위생안전성학회지
• /
• 제14권3호
• /
• pp.270-276
• /
• 1999

Alteromonas sp. SR-14의 배양여액을 사용하여 C. calcitrans의 증식에 미치는 영향과 조류 증식저해 물질의 특성을 살펴보았다. Alteromonas sp. SR-14의 peptone broth 배양여액은 C. calcitrans에 대하여 증식 저해 활성을 나타내었으며, 이 균에 의한 조류 증식 저해 물질은 온도 $15~20^{\circ}C$, pH 7.0~9.0, 염분 농도 $23~30{\textperthousand}$의배양 조건에서 강한 활성으로 생성되었으며, 이러한 조건(온도 $20^{\circ}C$, pH 8.0, 염분 농도 $30\textperthousand$)에서는 정지기부터 활성이 증가하였다. Alteromonas sp. SR-14가 peptone broth에서 생산하는 조류 증식 저해 물질의 분자량은 약 3KDa~12KDa의 복합 물질이었는데, $100^{\circ}C$에서 10분간 열처리하였을 때 3~10KDa 이하의 물질은 내열성이 있었으나 10KDa 이상의 물질은 불활성 되었다.