• Journal of Advanced Navigation Technology
• /
• v.26 no.2
• /
• pp.85-90
• /
• 2022

In this study, in order to test the performance of the aircraft system, a threat signal simulator that can transmit a signal similar to the actual threat to the aircraft under test with high power was designed. The high-power threat signal simulator should be able to transmit broadband (UHF band, L band, S band, X band) communication signals and radar signals, and control to transmit signals accurately directed to the aircraft through interfacing tracking radar. The signal strength of the developed equipment is 63 dBm to 93 dBm or more depending on type of signal, and the tracking precision is less than 0.1 degree, which satisfies the required performance. And it was confirmed that the antenna of the high-power threat signal simulator can accurately direct the signal to the aircraft position through the tracking radar interfacing.

• Journal of the Korean Institute of Navigation
• /
• v.15 no.1
• /
• pp.1-9
• /
• 1991

The coaxial sample holder with 20mm in diameter and the adaptor from type N connector-to-20mm${\phi}$ coaxial tube are designed and manufactured which have been used for designing and measuring the fabricated microwave absorber. In addition, the measure in method of material constants of the microwave absorbers is described, which is focused on minimizing the error due to the sample's shapes, the fitting conditions, etc. After describing the design method of a single-layed microwave absorber, the microwave absorbers for X-band, C-band and S-band RADARs are designed and fabricated, respectively, which are composed of ferrite, carborn, and binder and have good performance. Futhermore, we develop the high performance microwave absorber in extremely wide-band type for RADAR, which is composed of different material and its mixing ratio and which could cover nearly from 4 to 10 GHz.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.9 no.4
• /
• pp.425-432
• /
• 2014

Necessity of compact X-band solid-state weather radar is required to provide weather data, which generate locally in a lot of Korea's mountainous area, rather than tube-type radar. Solid State Power Amplifier (SSPA) for using Dual-polarization method in weather radar is able to obtain desired high output by combining many low output power devices in parallel. Thus, Power combiner applying to high-output power amplifier has disadvantages such as path loss, ballast resistance problem by high frequency and high power, heat release. Therefore, In this paper we demonstrated the excellence of isolation, which is the result from modified Gysel power combiner. As a result, we designed X-band 250W solid state power amplifier with peak power 54dBm, 25% power efficiency for weather radar.

• Journal of Ship and Ocean Technology
• /
• v.10 no.4
• /
• pp.34-48
• /
• 2006

The visual observation of wave condition depends on the observer's skill and experience. Also, the environmental conditions such as light and cloud heavily influence the visual measurement. In the speed test of sea trial, the wave measurement should be objective and accurate. In this paper, the problems of visual measurement and their effects on speed test are described. To overcome those problems, we developed the wave measurement system using commercial marine X-band radar, WaveFinder. The system installed at inland base was calibrated by waverider buoy and then the system's operability was defined. Onboard tests had also been performed three times for formal wave measurement to correct the ship speed. The results illustrated very good agreement with visual observation by experts. It can be concluded that the system would be useful to measure wave and swell information for the sea trial, irrespective of day and night.

• Journal of Advanced Marine Engineering and Technology
• /
• v.31 no.8
• /
• pp.970-974
• /
• 2007

A mixer is a key component in the wireless communication systems. In this paper, we design a mixer which is used in a frequency modulated continuous wave(FMCW) radar system. The frequency sweep range of the radar is from 10 GHz to 11 GHz. The transmitted and received signals of the FMCW radar are applied to LO and RF ports of the mixer, respectively, but the frequency difference between the two signals, which is called "a beat frequency" is under a few KHz and depending on the distance to target. Thus the isolation between the LO and RF ports is very important factor to design this mixer. In this paper we propose a single balanced resistive mixer using GaAs MESFET for this application. We first design a single-ended type resistive mixer using a simulation tool, then design a balanced type to increase the LO-to-RF isolation of the mixer. We fabricated the mixer on the substrate of dielectric constant 10 and thickness 0.635 mm. The measured results show that the isolation and conversion loss of the mixer over the frequency band is 20dB and 10.5dB, respectively. The LO input power for operating the proposed mixer is +3dBm, which is lower than a general conventional mixer's LO power. The 1 dB compression point is 6dBm.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.18 no.5
• /
• pp.97-102
• /
• 2018

In this paper, W-band Waveform Generator for compact radar has been designed and fabricated. DDS (Direct Digital Synthesizer) is applied to generate CW (Continuous Wave) and FMCW (Frequency Modulation Continuous Wave) waveform at high speed. We designed two LO (Local Oscillator) paths for functions of distance delay and distance tracking tests at the prpposed system without extra test equipment. Two mode selections are provided by switch. It is observed that fabricated waveform generator performs -91 dBc/Hz phase noise at offset 1 kHz and -63.2 dBc spurious. Proposed W-band Waveform Generator is expected to apply for W-band compact radar transceiver module.

• International Journal of Advanced Culture Technology
• /
• v.7 no.4
• /
• pp.236-241
• /
• 2019

This paper will read about a multichannel frequency-modulated continuous wave (FMCW) radar sensor with switching transmit (TX) antennas is developed at W-band. To achieve a high angular resolution, a uniform linear array consisting of 5 switching-TX and 12 receive (RX) antennas is employed with the digital beamforming technique. The overall radar front-end module comprises a W-band transceiver and TX/RX antennas. A multichannel transceiver module consists of 5 up-conversion and 12 down-conversion channels, where one of the TX channels is sequentially switched ON. For developing transmitter, we developed an HPA (high power amplified) MMIC chip for W-band radar system and fabricated a transmitter module using this chip. In order to develop the W-band transmitter, we analyzed the important antenna transition structure from HPA MMIC line to W/G (Waveguide)antenna via M/S(microstrip) and fabricated it with 5 transmission channels. As a result, the output power of the transmitter was within 1 dB of the error range after analysis and measurement under normal temperature and environmental conditions.

• Atmosphere
• /
• v.27 no.4
• /
• pp.467-481
• /
• 2017

A correction method of reflectivity in partial beam blockage (PBB) area is suggested, which is based on the combination of digital terrain information and self-consistency principle between polarimetric observation. First, the reflectivity was corrected by adding the radar energy loss estimated from beam blockage simulation using digital elevation model (DEM) and beam propagation geometry in standard atmosphere. The additional energy loss by unexpected obstacles and non-standard beam propagation was estimated by using the coefficient between accumulated reflectivity ($Z_H$) and differences of differential phase shift (${\Phi}_{DP}$) along radial direction. The proposed method was applied to operational S-band dual-polarization radar at Jindo and its performance was compared with those of simulation method and self-consistency method for six rainfall cases. When the accumulated reflectivity and increment of ${\Phi}_{DP}$ along radial direction are too small, the self-consistency method has failed to correct the reflectivity while the combined method has corrected the reflectivity bias reasonably. The correction based on beam simulation showed the underestimation. For evaluation of rainfall estimation, the FBs (FRMSEs) of simulation method and self-consistency principle were -0.32 (0.59) and -0.30 (0.57), respectively. The proposed method showed the lowest FB (-0.24) and FRMSE (0.50). The FB and FMSE were improved by about 18% and by 19% in comparison to those before correction (-0.42 and 0.70). We can conclude that the proposed method can improve the accuracy of rainfall estimation in PBB area.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.17 no.1
• /
• pp.1-7
• /
• 2013

The interference among the rain radars and interference in the adjacent wireless station due to the spurious signals from the rain radar were analyzed in this paper. The rain radar measures the rain intensity using S-band signal. The measured data are utilized in forecasting the rainfall. The interference among the rain radars or in the adjacent wireless stations may be caused by the operation with low elevation angle and the high output power. Based on the propagation analysis of S band signal and the deduced interference protection ratio of rain radar, the interference due to the rain radar are analyzed. Also, the radiation spectrum characteristics of a rain radar are deduced from the caused interference effects by the spurious signals of the rain radar. To minimize the interference effects for adjacent wireless stations, it is required to get the rejection characteristics of spurious signals above 105 dB. In viewpoints of interference for rain radars, it is necessary to operate the rain radar with a different PRF and operation time opposite to adjacent rain radars.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.14 no.5
• /
• pp.825-832
• /
• 2011

In this paper, we described the design and measurement results of a Front-End Receiver for S-band active phased array radar. The Front-End Receiver has input P1dB of -4dBm and IIP3 of 7dBm. The measurement results show that gain is $24{\pm}0.7dB$, noise figure are less than 2.3dB over the frequency range of $fc{\pm}0.2GHz$. The Front-End Receiver can protect the receiver path from large input signals with a maximum peak power of multi-kW and recovery time is less than 0.8us. The measurement results satisfy all specifications.