• Transactions of the Korean hydrogen and new energy society
• /
• v.31 no.3
• /
• pp.328-336
• /
• 2020

In the Francis turbine, the leakage flow through the runner gaps which are between the runner and the stator structure influences the internal flow and hydraulic performance. Thus, the investigation for the flow characteristics induced by the runner gaps is important. However, the runner gaps are often disregarded by considering the time and cost of the numerical analysis. Therefore, in this study, the flow characteristics according to runner gaps of the Francis turbine model were investigated including the leakage flow of the runner cone. The three-dimensional unsteady Reynolds-averaged Navier-Stokes analyses were conducted using a scale-adaptive simulation shear stress transport as a turbulence model for observing the influence of the leakage flow on the internal flow and hydraulic performance. The efficiencies were decreased slightly with runner gaps; and the complicated flows were captured in the gaps.

• Tribology and Lubricants
• /
• v.39 no.2
• /
• pp.81-85
• /
• 2023

This study presents an experimental investigation of the effects of surface roughness on gas foil thrust bearing (GFTB) performance. A high-speed motor with the maximum speed of 80 krpm rotates a thrust runner and a pneumatic cylinder applies static loads to the test GFTB. When the motor speed increases and reaches a specific speed at which a hydrodynamic film pressure generated within the gap between the thrust runner and test GFTB is enough to support the applied static load, the thrust runner lifts off from the test GFTB and the friction mechanism changes from the boundary lubrication to the hydrodynamic lubrication. The experiment shows a series of lift-off test and load-carrying capacity test for two thrust runners with different surface roughnesses. For a constant static load of 15 N, thrust runner A with its lower surface roughness exhibits a higher start-up torque but lower lift-off torque than thrust runner B with a higher surface roughness. The load capacity test at a rotor speed of 60 krpm reveals that runner A results in a higher maximum load capacity than runner B. Runner A also shows a lower drag torque, friction coefficient, and bearing temperature than runner B at constant static loads. The results imply that maintaining a consistent surface roughness for a thrust runner may improve its static GFTB performance.

• Journal of Advanced Marine Engineering and Technology
• /
• v.38 no.10
• /
• pp.1225-1231
• /
• 2014

This paper presents the performance characteristic of a Francis hydro turbine with an inline casing. This turbine is designed for city water supply system. Due to large changes in ground elevation with high points and low points, some systems may experience larger-than-normal required pressures in areas with low ground elevations. One way to dissipate these excess pressures is by the use of an inline-turbine instead of an inline-pressure reducing valve. For best applicability and minimal space consumption, the turbine is designed with an inline casing instead of the common spiral casing. As a characteristic of inline casing, the flow accesses to the runner in the radial direction, showing a low efficiency. The installation of vanes improves the internal flow and gives the positive encouragement to the output power. For the power transmission to the outside of the turbine casing from the runner axis, a belt passage is designed in the inline casing, as its influence, the region after the belt passage shows a relatively low output power. The clearance gap in the runner side space is considered, in which a small volume of flow is contracted into the clearance gap, forming the leakage flow. The leakage flow leads to a decrease in the efficiency.

• Journal of Technologic Dentistry
• /
• v.30 no.2
• /
• pp.57-63
• /
• 2008

Statement of problem: Conventional techniques for implant framework fabrication produce significant error that is inconsistent with passive-fit requirement for osseointegrated implants. One of the etiologic factors which cause the errors is a sprue which may deform the framework during solidification and contraction. Purpose: This study was aimed to evaluate objectively effect of the sprue design on the accuracy of fit of implant prosthesis. Materials and method: Three different designs were considered relative to effect of casting accuracy. The first design had straight sprues and a button of excess alloy at the non-casting end of the sprues. The second was runner bar design(with the button). The last was straight sprues design(without the button). Gold cylinder and laboratory analogue had been used to diminish variables affecting to casting accuracy. Gold alloy and pressure-vacuum casting machine had been used. Marginal gap had been measured by SEM. One-way ANOVA and Duncan test had been used for statistical analysis. Results: The first design showed $79.87{\pm}13.95{\mu}m$ marginal gap. The second and third were $40.17{\pm}15.8{\mu}m$ and $35.17{\pm}9.95{\mu}m$ respectively. Conclusion: Straight sprues without button and runner bar designs were more accurate than straight sprues with button design(P<.05).

• International Journal of Fluid Machinery and Systems
• /
• v.7 no.4
• /
• pp.151-159
• /
• 2014

Low head hydropower is one of realistic renewable energies. The Darrieus-type hydro turbine with an inlet nozzle is available for such low head conditions because of its simple structure with easy maintenance. Experimental and numerical studies are carried out in order to examine the effects of gap distances between the runner pitch circle and two edges of inlet nozzle on turbine performances. By selecting narrower gaps of left and right edges, the performance could be improved. From the results of two dimensional numerical simulations, the relation between the performance and flow behaviors around the Darrieus blade are discussed to obtain the guideline of appropriate inlet nozzle design.

• Tribology and Lubricants
• /
• v.37 no.4
• /
• pp.117-124
• /
• 2021

In this study, we perform a 3D CFD conjugate analysis according to the shape of the foil ramp of the air foil thrust bearing, analyze the flow characteristics inside the bearing, and compare the results corresponding to the two shapes. Air has a lower viscosity than lubricating oil. Therefore, the thrust runner of the bearing must rotate at high speed to support the load. The gap between thrust runner and foil is significantly smaller than that of the oil bearing. Hence, it is crucial to analyze the complex flow characteristics inside the bearing to predict the complex flow inside the bearing and performance of the bearing. In addition, flow characteristics may appear differently depending on the ramp shape of the bearing foil, which may affect bearing performance. In this study, we numerically analyze the main flow path of air flowing into the bearing and the secondary flow path used for cooling the bearing using the commercial CFD software ANSYS CFX and compare the flow characteristics for straight and curved foil ramp shapes. Notably, there is a difference in the speed of the flowing air according to the shape of the ramp, which affects the bearing performance.

• International Journal of Fluid Machinery and Systems
• /
• v.3 no.4
• /
• pp.342-351
• /
• 2010

During the operation of a hydro turbine the fluid mechanical pressure loading on the turbine blades provides the driving torque on the turbine shaft. This fluid loading results in a structural load on the component which in turn causes the turbine blade to deflect. Classically, these mechanical stresses and deflections are calculated by means of finite element analysis (FEA) which applies the pressure distribution on the blade surface calculated by computational fluid dynamics (CFD) as a major boundary condition. Such an approach can be seen as a one-way coupled simulation of the fluid structure interaction (FSI) problem. In this analysis the reverse influence of the deformation on the fluid is generally neglected. Especially in axial machines the blade deformation can result in a significant impact on the turbine performance. The present paper analyzes this influence by means of fully two-way coupled FSI simulations of a propeller turbine utilizing two different approaches. The configuration has been simulated by coupling the two commercial solvers ANSYS CFX for the fluid mechanical simulation with ANSYS Classic for the structure mechanical simulation. A detailed comparison of the results for various blade stiffness by means of changing Young's Modulus are presented. The influence of the blade deformation on the runner discharge and performance will be discussed and shows for the configuration investigated no significant influence under normal structural conditions. This study also highlights that a two-way coupled fluid structure interaction simulation of a real engineering configuration is still a challenging task for today's commercially available simulation tools.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2022.05a
• /
• pp.329-332
• /
• 2022

This study aims to identify problems with existing e-learning content and non-face-to-face class methods, improve students' concentration, improve class achievement and educational effectiveness, and propose an artificial intelligence class system design using a web server. By using the function of face and eye tracking using OpenCV to identify attendance and concentration, and by inducing feedback through voice or message to questions asked by the instructor in the middle of class, learners relieve boredom caused by online classes and test by runner If the score is not reached, we propose an artificial intelligence education program system design that can bridge the academic gap and improve academic achievement by providing educational materials and videos for the wrong problem.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2022.10a
• /
• pp.280-283
• /
• 2022

This study aims to identify problems with existing e-learning content and non-face-to-face class methods, improve students' concentration, improve class achievement and educational effectiveness, and propose an artificial intelligence class system design using a web server. By using the function of face and eye tracking using OpenCV to identify attendance and concentration, and by inducing feedback through voice or message to questions asked by the instructor in the middle of class, learners relieve boredom caused by online classes and test by runner If the score is not reached, we propose an artificial intelligence education program system design that can bridge the academic gap and improve academic achievement by providing educational materials and videos for the wrong problem.

• Management & Information Systems Review
• /
• v.22
• /
• pp.137-165
• /
• 2007

It seems high time to increase productivity by adopting e-business to overcome challenges posed by both external factors including the appreciation of Korean won, oil hikes and fierce global competition and domestic issues represented by disparities between large corporations and small and medium enterprises (SMEs), Seoul metropolitan and local cities, and export and domestic demand all of which weaken future growth engines in the Korean economy. The demands of the globalization era are for innovative changes in businessprocess and industrial structure aiming for creating new values. To this end, e-business is expected to play a core role in the sophistication of the Korean economy through new values and innovation. In order to examine business performance in e-business-adopting industries, this study analyzed the home shopping industry by closely looking into the financial ratios including the ratio of net profit to sales, the ratio of operation income to sales, the ratio of gross cost to sales cost, the ratio of gross cost to selling, general and administrative (SG&A) expense, and return of investment (ROI). This study, for best outcome, referred to corporate financial statements as a main resource to calculate financial ratios by utilizing Data Analysis, Retrieval and Transfer System (DART) of the Financial Supervisory Service, one of the Korea's financial supervisory authorities. First of all, the result of the trend analysis on the ratio of net profit to sales is as following. CJ Home Shopping has registered a remarkable increase in its ratio of net profit rate to sales since 2002 while its competitors find it hard to catch up with CJ's stunning performances. This is partly due to the efficient management compared to CJ's value of capital. Such significance, if the current trend continues, will make the front-runner assume the largest market share. On the other hand, GS Home Shopping, despite its best organized system and largest value of capital among others, lacks efficiency in management. Second of all, the result of the trend analysis on the ratio of operation income to sales is as following. Both CJ Home Shopping and GS Home Shopping have, until 2004, recorded similar growth trend. However, while CJ Home Shopping's operating income continued to increase in 2005, GS Home Shopping observed its operating income declining which resulted in the increasing income gap with CJ Home Shopping. While CJ Home Shopping with the largest market share in home shopping industryis engaged in aggressive marketing, GS Home Shopping due to its stability-driven management strategies falls behind CJ again in the ratio of operation income to sales in spite of its favorable management environment including its large capital. Companies in the Group B were established in the same year of 2001. NS Home Shopping was the first in the Group B to shift its loss to profit. Woori Home Shopping has continued to post operating loss for three consecutive years and finally was sold to Lotte Group in 2007, but since then, has registered a continuing increase in net income on sales. Third of all, the result of the trend analysis on the ratio of gross cost to sales cost is as following. Since home shopping falls into sales business, its cost of sales is much lower than that of other types of business such as manufacturing industry. Since 2002 in gross costs including cost of sales, SG&A expense, and non-operating expense, cost of sales turned out to have remarkably decreased. Group B has also posted a notable decline in the same sector since 2002. Fourth of all, the result of the trend analysis on the ratio of gross cost to SG&A expense is as following. Due to its unique characteristics, the home shopping industry usually posts ahigh ratio of SG&A expense. However, more than 80% of SG&A expense means the result of lax management and at the same time, a sharp lower net income on sales than other industries. Last but not least, the result of the trend analysis on ROI is as following. As for CJ Home Shopping, the curve of ROI looks similar to that of its investment on fixed assets. As it turned out, the company's ratio of fixed assets to operating income skyrocketed in 2004 and 2005. As far as GS Home Shopping is concerned, its fixed assets are not as much as that of CJ Home Shopping. Consequently, competition in the home shopping industry, at the moment, is among CJ, GS, Hyundai, NS and Woori Home Shoppings, and all of them need to more thoroughly manage their costs. In order for the late-comers of Group B and other home shopping companies to advance further, the current lax management should be reformed particularly on their SG&A expense sector. Provided that the total sales volume in the Internet shopping sector is projected to grow over 20 trillion won by the year 2010, it is concluded that all the participants in the home shopping industry should put strategies on efficient management on costs and expenses as their top priority rather than increase revenues, if they hope to grow even further after 2007.