• Design & Manufacturing
• /
• v.8 no.1
• /
• pp.40-44
• /
• 2014

As a rotating machine element, plastic gears are more and more widely used in such as industrial machine element, since plastic gear is lighter, higher wear-resistance, and higher vibration absorbing ability than metal gears. When operating plastic parts, tooth breakage and fatigue life shortened due to increasing number of applying load and tooth flank temperature rising, such that accuracy of plastic gears is divided from allowable range to cause vibration and noise. On this study, a internal plastic gears are developed which improved the filling balance molding process by a new injection mold structure. The new mold structure called HR3P(hot runner type 3plate mold). As the result from this studies, we obtained a very accurate roundness internal gears by using design of experiment.

• International Journal of Fluid Machinery and Systems
• /
• v.4 no.2
• /
• pp.243-254
• /
• 2011

In the present paper, we focus on the flow computation of a low head Propeller turbine at a wide range of design and off-design operating conditions. First, we will present the results on the efficiency hill chart prediction of the Propeller turbine and discuss the consequences of using non-homologous blade geometries for the CFD simulation. The flow characteristics of the entire turbine will be also investigated and compared with experimental data at different measurement planes. Two operating conditions are selected, the first one at the best efficiency point and the second one at part load condition. At the same time, for the same selected operating points, the numerical results for the entire turbine simulation will be compared with flow simulation with our standard stage calculation approach which includes only guide vane, runner and draft tube geometries.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2006.05a
• /
• pp.577-578
• /
• 2006

In this paper, the rubber behavior was calculated for obtaining the optimal process condition which is for producing a transformer with a given performance. This study was carried out using the computer simulation of injection mold filling and packing simulations. In order to remove the crack of product, proper locations of the runner and cooling system configurations could be determined. Based on these results, the transformer is developed by injection molding and guidelines of part design, mold design and processing conditions are established. Finally, the cast savings, cycle time reduce and improvement of productivity will be obtained.

• 한국금형공학회:학술대회논문집
• /
• 2008.06a
• /
• pp.129-133
• /
• 2008

As a rotating machine element, plastic gears are more and more widely used in such as industrial machine element, since plastic gear is lighter, higher wear-resistance, and higher vibration absorbing ability than metal gears. When operating plastic parts, tooth breakage and fatigue life shortened due to increasing number of applying load and tooth flank temperature rising, such that accuracy of plastic gears is divided from allowable range to cause vibration and noise. On this study, a internal plastic gears are developed which improved the filling balance molding process by a new injection mold structure. The new mold structure called HR3P(hot runner type 3plate mold). As the result from this studies, we obtained a very accurate roundness internal gears by using design of experiment.

• Design & Manufacturing
• /
• v.17 no.4
• /
• pp.57-62
• /
• 2023

As a representative method for mass production, a multi-cavity type mold capable of simultaneously molding products of the same shape can be applied. It has the advantage of improving the productivity from several times to several tens of times, but it may cause disadvantages which is the quality deviation with each cavity. This study, therefore, has tried to increase the cavity filling balance by using a melt flipper and a flow distance control part in the runner part of the mold. Along with this, the design and manufacturing of air vents during injection molding have been verified through experimental methods to achieve a higher level of multi-cavity filling balance and dimensional accuracy.

• Journal of Korea Foundry Society
• /
• v.36 no.6
• /
• pp.208-214
• /
• 2016

Casting defects, which are closely related to entrapped air bubbles and metallic oxides, occur very frequently in the casting process. Many researchers have shown that these defects can be reduced by adopting an appropriate gating system design. But, it is difficult for field engineers to identify a specific gating system that is more appropriate for their products. In this study, we tried to draw a comparison of gating system designs with and without ceramic foam filters. A ceramic foam filter was added to the horizontal runner just after the sprue to prevent air bubble generation and to reduce turbulence without change of the gating system design. To verify the effects of initial pouring velocity, the experiment was conducted with four different amounts of water volume in the reservoir. Results of the water modeling experiment applying the filter showed remarkably changed flow characteristics. Although the study confirmed that use of the filter may change the flow characteristics, it needs to be noted that only filter use alone cannot solve all the problems caused by a poorly designed gating system.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.27 no.6
• /
• pp.1020-1027
• /
• 2003

A traditional mold design has been conducted by an experience-based trial and error, whereby the mold designer would decide the gate locations and processing conditions based on the caring characteristics and its functional requirements. The paper suggests an optimal gate location and processing conditions in the injection molding using a global search method referred to as micro genetic algorithm( ${\mu}$ GA). ${\mu}$ GA yields the optimal solution with a small size of population without respect to design variables for saving time that is needed to calculate the fitness of many individuals. Due to the reason, the paper uses a commercial analysis package of injection molding(CAPA) to analysis a state of flux. In addition to that, axiomatic approach .is applied in the beginning of design. It is a useful method to draw a well-organized and reasonable idea to handle a problem.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.11 no.5
• /
• pp.1552-1557
• /
• 2010

The cylindrical gear in power window motor assembly is important to doors of automobile. This study is performed for the purpose of getting a manufacturing technique instead of large quantities import and six-cavity mold production. This multi-cavity cylindrical gear is produced under five procedures. The first, mold design of mass-production, the second, making a CAE model for mass-production, the third, manufacturing of sample mold, the fourth, trying-out and measuring of 3 dimensional design, the fifth, acquisition of data analysis and mold modification. Among them, analysis of mass-production using CAE, designing and manufacturing of multi-cavity are successfully performed. In the results, it is concluded that the mold for one gate and eight-cavity based on hot-runner is suitable for making a cylindrical gear.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.18 no.11
• /
• pp.1-8
• /
• 2019

In this study, we design the feed system and process conditions for a lamp garnish lens of an automobile. For this purpose, four design alternatives are presented and injection molding simulation analyses are performed. The optimal feed system is selected by considering the formability of the product and the cost of mold manufacture. The product formability is assessed by the weld line, warpage, sink mark and the maximum injection pressure, whereas the mold-making cost is estimated by the number of valve gates in the hot runner system. To improve the product formability, process conditions are optimized using an experimental design approach named one-factor-at-a-time. No weld line is generated as a result of the optimization. In addition, it is found the warpage and sink mark are reduced while the maximum injection pressure is increased, compared with those before the optimization.

• Journal of Korea Foundry Society
• /
• v.20 no.2
• /
• pp.97-103
• /
• 2000

In this study, a design of experiment, Taguchi method, was applied to optimize gating system design of escalator step die casting parts. Six shape factors which affect filling sequence of melt are adopted and divided into two levels respectively. Initial feeding differences of melt which were calculated by using S/N(signal-to-noise) ratio in each condition were demonstrated with the simulation of Flow-3D software program. Variations of S/N ratio according to shape factors were obtained and the optimal condition of gating system could also be obtained. It could be found that width of gate, contact angle of gate, thickness of runner are more effective factors on the filling sequence of melt than the others in this case of escalator step die casting parts. It showed that the economical gating system and sound filling sequence of melt were obtained by using Taguchi method.