• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.11 no.12
• /
• pp.1133-1138
• /
• 1998

In this paper, we obtained the monodomain alignment of nematic liquid Crystal(NLC) in the cell fabricated by transcription alignment method on polyimide(PI) surface with side chain. It is considered that the LC alignment produced by the transcription alignment method is attributed to a memory effect of the NLC on PI surfaces. Also we observed that the generated pretilt angle of NLC is about $3.7^{\circ}$ with transcription alignment on PI surface. Next, we measured that the voltage-transmittance characteristics of transcription-aligned TN-LCD are almost same compared to rubbing-aligned TN-LCD. Also, we measured that the curve of transcription-aligned TN-LCD is less sharp than that of the rubbing-aligend TN-LCD in the decay time characteristics. It is considered that the response time characteristics of transcription-aligned TN-LCD are attributed to the weak anchoring strength between the LC molecules and the polymer surface.

• Electrical & Electronic Materials
• /
• v.9 no.7
• /
• pp.733-744
• /
• 1996

본 논문에서는 최근 LCD소자에 있어서 큰 이슈로 등장한 표면 액정배향기술 및 광시야각 기술에 관하여 설명하였다. 표면 액정배향기술에 있어서는 종래의 러빙법에 대신하여 편광된 자외선을 조사하여 액정분자를 배열시키는 광배향제어법이 큰 기대를 모으고 있으며, 이 기술은 프리틸트 각 발생제어기술과 신뢰성이 과제로 남아있다. 광시야각 기술에 있어서는 최근까지 여러 방식이 제안되어왔으며 그 중에서도 현재로는 광학보상법, IPS방식 등이 실용화가 진행되고 있다. 그러나 향후 다른 방식의 기술발전 여부에 따라 상황이 변화될 것으로 예상된다. 각각의 방식에 따라 서로 장단점을 지니고 있어 향후 이용분야에 따라 용도를 나누어서 응용될 것으로 기대되어진다. LCD소자는 이러한 기술개발의 결과로 평판디스플레이 소자 중에서 더욱 확고한 위치를 확보할 것이며 더 많은 시장성을 점유할 것으로 전망된다. 이상으로 본 논문에서는 LCD소자의 표면액정 배향기술 및 광시야각 기술에 관하여 해설하였으며 표면액정 배향기술에 관하여는 간단히 소개하였으나 이 내용에 관하여는 다음 기회에 상세히 소개하기로 한다.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.06a
• /
• pp.435-436
• /
• 2007

In general, Single gap transflective FFS display has an in-cell retarder (ICR) between reflective electrode and liquid crystal (LC) layer. Therefore, Operating voltage is highly increased due to this thick dielectric material. But, we also knew the phenomenon that the increasing rate of Vop is different whether the 1st common electrode was composed of plate type or slit type. In this paper, the common electrode in transmissive part was composed of slit type which had less steepness effect of the V op and in reflective part was composed of plate type. The rubbing angle of reflective part can be adjusted properly to match the voltage dependent transmittance and reflectance.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2006.08a
• /
• pp.1601-1604
• /
• 2006

A novel photo-alignment scheme using normally incident periodically intensity-modulated UV light has been developed and demonstrated to efficiently yield a stable pretilt angle of nematic liquid crystals by single exposure. The scheme, referred to as the "photo-rubbing", consists in unidirectional scan of the intensity-modulated UV light over the photo-alignment film, which causes asymmetrical photo-reactions in the film. We show here its successful application to multi-domain alignment processing. Thanks to the normal incidence, the photo-rubbing removes the instrumental disadvantages of the conventional oblique incidence technique, thereby providing a true practical solution for photo-alignment.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2003.07a
• /
• pp.585-588
• /
• 2003

We have studied how rubbing direction affects generation of disclination line in transmissive microdisplay for $90^{\circ}$ twisted nematic (TN) mode with pixel size of $22.2{\mu}m$. The rubbing direction of bottom substrate is changed from $0^{\circ}$ to $-135^{\circ}$ with a decrease step of $45^{\circ}$, and the results show that the generation regions of the disclination line are of a smallest size in $-135^{\circ}$ direction. The results were the same although the pixel size decreased. Consequently, the use of proper rubbing direction of liquid crystal can help overcome the problems of low aperture ratio and low contrast ratio in transmissive-type microdisplays. In addition, the pretilt angle of initial liquid crystal is found to make an important contribution to generation of the disclination line.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.338-338
• /
• 2009

To date, rubbing has been widely used to align LC molecules uniformly. Although rubbing can be simple, it has fundamental problems such as the generation of defects by dust and static electricity, and difficulty in achieving a uniform LC alignment on a large substrate. Therefore, noncontact alignment has been investigated. Ion beam induced alignment method, which provides controllability, nonstop process, and high resolution display. We investigated the high pretilt angle effects on electro-optical properties of ion beam (IB)-irradiated liquid crystal cells. on a blended polymer surface. High pretilt angle of liquid crystals IB-irradiated on a blended polymer surface including such as 5% and 10% of homeotropic polymer contents can' be achieved. The threshold voltages of IB-irradiated twisted nematic (TN) cells on a blended polymer surface decrease with increasing the pretilt angle. Also, the rising time of IB-irradiated TN cells decreases with increasing the pretilt angle. However the decay time of IB-irradiated TN cells increases with increasing the pretilt angle. Consequently, the electro-optical properties of IB-irradiated TN cells depend strongly on the pretilt angle in a blended polymer surface.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.04a
• /
• pp.133-135
• /
• 2003

The washing effects on pretilt angle generation in a nematic liquid crystal (NLC), 4-n-pentyl-4’-cyanobiphenyl (5CB) on a rubbed polyimide (PI) surface with trifluoromethyl moiety have been successfully studied. The pretilt angle of 5CB is increased by the washing process on the rubbed PI surface. The surface tension on the rubbed PI surface increases with the rubbing strength RS and then saturated above RS=150 mm. The pretilt angle of 5CB for all washing processes on the rubbed PI surface decreases with the surface tension. We have found that the pretilt angle of 5CB on the rubbed PI surface may be attributed van der walls (VDW) dispersion interaction between the LC molecules and the polymer surfaces having trifluoromethyl moieties.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.11 no.10
• /
• pp.911-917
• /
• 1998

In this paper, we have investigated the generation of pretilt angle for nematic liquid crystal (NLC) in a cell with oblique non-polarized ultraviolet(UV) light irradiation polyimide (PI) surface. It was found that the monodomain alignment of the NLC is obtained with an angle of incidence of 70∼85。 on PI surface. It is considered that the monodomain alignment of NLC is attributed to anisotropic of NLC is about 3。 with and angle of incidence of 70∼75。. Finally, we observed that the voltage-transmittance, response time, and voltage-holding-ratio(VHR) characteristics of photo-aligned twisted nematic(TN)-LCD with and angle of incidence of 85。 on PI surface were almost same compared to rubbing -treated TN-LCD.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.04a
• /
• pp.41-41
• /
• 2008

In general, polyimides (PIs) are used in alignment layers in liquid crystal displays (LCDs). The rubbing alignment technique has been widely used to align the LC molecules on the PI layer. Although this method is suitable for mass production of LCDs because of its simple process and high productivity, it has certain limitations. A rubbed PI surface includes debris left by the cloth, and the generation of electrostatic charges during the rubbing induces local defects, streaks, and a grating-like wavy surface due to nonuniform microgrooves that degrade the display resolution of computer displays and digital television. Additional washing and drying to remove the debris, and overwriting for multi-domain formation to improve the electro-optical characteristics such as the wide viewing angle, reduce the cost-effectiveness of the process. Therefore, an alternative to non-rubbing techniques without changing the LC alignment layer (i.e, PI) is proposed. The surface of LC alignment layers as a function of the ion beam (IE) energy was modified. Various pretilt angles were created on the IB-irradiated PI surfaces. After IB irradiation, the Ar ions did not change the morphology of the PI surface, indicating that the pretilt angle was not due to microgrooves. To verify the compositional behavior for the LC alignment, the chemical bonding states of the ill-irradiated PI surfaces were analyzed in detail by XPS. The chemical structure analysis showed that ability of LCs to align was due to the preferential orientation of the carbon network, which was caused by the breaking of C=O double bonds in the imide ring, parallel to the incident 18 direction. The potential of non-rubbing technology for fabricating display devices was further conformed by achieving the superior electro-optical characteristics, compared to rubbed PI.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.11a
• /
• pp.399-399
• /
• 2007

Recently, it is widely studied to liquid crystal (LC) alignment using ion-beam exposure. Because conventional rubbing method has some problems such as defects from dust and electrostatic charges during rubbing process. Therefore rubbing-free techniques like ion-beam method are strongly required. We studied LC alignment by controlling ion-beam energy density and electro-optical (EO) characteristics of twisted nematic LC on the polyimide surface. In this experiment, a good uniform alignment of the nematic liquid crystal (NLC) with the ion-beam exposure on the polyimide (PI) surface was observed. In addition, it can be achieved the good EO properties of the ion-beam-aligned twisted nematic liquid crystal display (TN-LCD) on PI surface.