• 접착 및 계면
• /
• 제16권2호
• /
• pp.69-75
• /
• 2015

돌침대에 사용되는 석재의 무게를 줄여 경량화를 추구하려면 석재의 두께를 줄이고 보강재료로 석재의 강도를 유지해야 한다. 본 연구에서는 돌침대용 석재/목재 보드 개발에 대한 연구를 진행하였다. 돌침대에 삽입될 돌의 무게를 줄이기 위해 석재와 목재를 접합하였다. 목재의 강도 향상과 표면개질을 위하여 열처리 조건에 따른 목재의 물성변화를 관찰하였다. 대기 조건에서 열처리한 목재의 경우 고온의 온도에 따라 목재의 강성이 높아졌다. 열처리 최적조건은 표면에너지와 인장, 굴곡 강도변화 경향을 바탕으로 $100^{\circ}C$ 조건임을 확인하였다. 석재와 목재간 높은 접착력을 확보하기 위해 최적의 접착제 조성을 연구하였다. 아민계 에폭시 접착제, 폴리우레탄(PU)계 접착제, 염화고무계(CR) 접착제 마지막으로 염화비닐초산계 접착제에 따른 석재와 목재간 랩 전단실험을 진행하였다. 랩 전단 실험 후 파단면을 관찰해볼 때 에폭시 접착제를 이용할 때 목재 기지의 인열 파괴가 발생되었다. 접착면에서의 전단력이 목재 자체의 파괴 강도보다 높다는 결과를 바탕으로 최적의 접착제 조건이 에폭시계 접착제임을 확인할 수 있었다.

• 한국측량학회:학술대회논문집
• /
• 한국측량학회 2002년도 창립 20주년기념 국제학술대회
• /
• pp.25-33
• /
• 2002

Historical maps are precious materials, which show spatial distribution of land use, streets and so on at the time when the maps were produced. In analysis of historical maps, the most practical method is to compare them with the present ones, for instance by overlaying them. However, the low precision, in the geometrical sense, of the historical maps makes the task of comparison very difficult. This drawback brings us the idea to incorporate the historical maps into GIS after rubber-sheet transformation, i.e. geometric correction, of them. It makes comparing and overlaying multiple maps from different time periods. Furthermore, it gives map-scales to the historical maps, which are not in general represented on the old maps, and if we allow ourselves to ignore the changes in terrain from past to present, it will make overlaying of present contour lines on the historical maps. As a result, we can bring the points of view of quantitative consideration and three-dimensional visualization into analyses of historical map. We have addressed incorporating historical maps produced in Edo period (1603-1867) in Japan into our GIS for Tokyo. This article shows the outline of our procedures and some applications, e.g., overlaying different maps from Edo period to present, quantitative analyses of land use in Edo, and visualization of landscape of Edo.

• Geomechanics and Engineering
• /
• 제22권3호
• /
• pp.219-226
• /
• 2020

Unconfined compression test (UCT) is widely conducted in laboratories to evaluate the mechanical behavior of frozen soils. However, its results are sensitive to the initial conditions of sample creation by freezing as well as the end-surface conditions during loading of the specimen into the apparatus for testing. This work compared ice samples prepared by three-dimensional and one-dimensional freezing. The latter created more-homogenous ice samples containing fewer entrapped air bubbles or air nuclei, leading to relatively stable UCT results. Three end-surface conditions were compared for UCT on ice specimens made by one-dimensional freezing. Steel disc cap with embedded rubber was found most appropriate for UCT. Three frozen materials (ice, frozen sand, and frozen silt) showed different failure patterns, which were classified as brittle failure and ductile failure. Ice and frozen sand showed strain-softening, while frozen silt showed strain-hardening. Subsequent investigation considered the influence of fines content on the unconfined compression behavior of frozen soil mixtures with fines contents of 0-100%. The mixtures showed a brittle-to-ductile transition of failure patterns at 10%-20% fines content.

• Elastomers and Composites
• /
• 제52권3호
• /
• pp.216-223
• /
• 2017

The additive manufacturing technology, also called 3D printing, is growing fast. There are several methods for 3D printing. Fused deposition modeling (FDM) type 3D printing is the most popular method because it is simple and inexpensive. Moreover, it can be used for printing various thermoplastic materials. However, it contains the cooling of layered road and causes thermal shrinkage. Thermal shrinkage should be controlled to obtain high-quality products. In this study, temperature distribution and cooling behavior of a layered road with cooling are studied through computer simulation. The thermal shrinkage of the layered road was simulated using the calculated temperature distribution with time. Shape variation of the layered road was predicted as cooling proceeded. Stress between the bed and the layered road was also predicted.This stress was considered as the detaching stress of the layered road from the bed. The simulations were performed for various thermal conductivities and temperatures of the layered road, bed temperature, and chamber temperature of a 3D printer. The simulation results provide detailed information about the layered road for FDM type 3D printing under operational conditions.

• Elastomers and Composites
• /
• 제52권4호
• /
• pp.295-302
• /
• 2017

Polyurethane dispersion (PUD) polymers were synthesized by using polyether and polyester polyol. The effect of ionomeric centers, r(NCO / OH) values, chain extender process, and chain extender types on the adhesion properties was investigated. In the case of polyether-based PUD, the ionic center, r value, chain extension process and chain extender types were not adjusted even after adjustment. In the case of polyester-based PUD, when the ionic center content was more than 2.5%, the state of adhesive strength was $2.0kgf/cm^2$ or more. On the other hand, the initial adhesive strength was excellent at about $1kgf/cm^2$ when the ionic center content was over 3.5%. When the r value was 1.3 or more, it was found that the initial bonding strength and the state of bonding strength were excellent at about $1kgf/cm^2$ and $2.1kgf/cm^2$ or higher, respectively. An IR spectrum analysis of the synthesized PUD confirmed that PUD was composed of urethane based on the N-H characteristic peak at $3340cm^{-1}$ and the urethane characteristic peak at $1730cm^{-1}$. Moreover, the characteristic peaks of the isocyanate ($2260cm^{-1}$) used in the preparation of the prepolymer were not observed. As a result, the residual -NCO was not observed, and urethane was completely synthesized.

• Elastomers and Composites
• /
• 제52권4호
• /
• pp.266-271
• /
• 2017

This study describes the influence of the amount of curing agent and curing temperature on the kinetics of polyurethane elastomers. The urethane prepolymer series was prepared by reacting toluene diisocyanate with polytetramethylene ether glycol at $80^{\circ}C$ for 1 h, and 4,4'-methylene bis(2-chloroaniline) was used as the curing agent. The ratio of the amine group of the curing agent to the isocyanate group of the urethane prepolymer was controlled from 0.85 to 1.05 at curing temperatures ranging from 80 to $120^{\circ}C$. The curing rate of the urethane prepolymer was monitored by observing the change in heat flow during the curing process using differential scanning calorimetry (DSC). As either the content of curing agent or the curing temperature was higher, the conversion rate to the polyurethane elastomer was high. The DSC results were compared with those obtained from using real-time FT-IR.

• Elastomers and Composites
• /
• 제52권4호
• /
• pp.309-316
• /
• 2017

In injection molding, the quality of an injection molded product varies greatly depending on the molding conditions. Many researche studies have been conducted on the quality analysis of molded parts according to the molding conditions such as injection pressure, injection temperature, and packing pressure. However, there have not been many studies on the V/P switchover timing. It is known that when a large pressure is applied to a cavity in the packing phase, the cavity pressure is most affected by the packing pressure. In addition, depending on the position (timing) of the packing pressure, it can have a direct influence on quality based on the shrinkage and dimensions of the molded parts. In this study, the change in pressure profile in the cavity according to the V/P switchover position is confirmed. A CAE analysis program (Moldflow) was used to simulate and analyze two models using the PC and PBT materials. In order to compare these results with the actual injection molding results, injection molding was performed for each V/P switchover position, and the correlation between simulation and experiment, especially for the shrinkage of molded parts, was evaluated.

• Elastomers and Composites
• /
• 제43권4호
• /
• pp.221-229
• /
• 2008

전분을 매트리스 고분자로 하여 아크릴 모노머인 2-ethylhexylacrylate와 methyl methacrylate, acrylic acid를 그래프트 중합하였다. 중합은 라디칼 유화중합에 의하여 전분의 함량을 증가시키면서 수행되었다. 효소인 $\alpha$-amylase 가 전분 대비 0.174% 투입되었을 때 가장 안정한 중합물이 얻어졌으며 전분의 함량이 증가함에 따라 중합물의 유리전이온도가 상승하였다. 전분 함량의 증가에 따라 계내의 -OH기가 많아짐에 따라 중합물의 입자 크기와 점도가 증가하였다. Peel strength는 전분 함량이 증가할수록 -OH기 증가에 의해 중합물이 피착체 표면과의 친화력 상승이 일어나서 증가하였다. 반면 초기 점착력은 전분 함량이 증가할수록 유리전이온도의 증가에 따라 필름의 경도가 증가하면서 감소하였다.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 1991년도 춘계학술대회논문집; 한국해사기술연구소, 대전; 1 Jun. 1991
• /
• pp.127-132
• /
• 1991

충격에 민감한 용기나 기계들은 운반이나 보관중에 받을 수 있는 진동충격 을 완화시키기 위해 충격 마운트를 이용하게 되며, 충격마운트는 용기나 기 계들이 허용하는 최대가속도와 이들이 취급되는 환경에 의해 적절히 선정되 어야 한다. 그러므로 내충격 설계는 최대 허용 가속도나 취급환경에 대한 사 양과 이 사양에 의한 충격 마운트의 선정, 그리고 선정된 내충격 시스템의 충격시험에 의한 오일 탬퍼의 결합용이 사용되기도 하지만 구조가 복잡하고 가격이 비싸서 대용량이 경우에만 국한되어 사용되고 있으며, 가장 경제적인 것은 방진고무를 사용한 것이다. 내충격 시스템은 일반적으로 큰 변형량을 요구하고 있으며, 방진고무의 경우 큰 변형에서는 hardening 스프링의 비선 형성을 가지고, 형상계수와 고무배합율에 따라 정적 스프링상수와 동적 스프 링상수가 큰 차이를 보이는 등, 설계상의 여러 제한이 있다. 그러나 방진고 무는 형상변화가 자유로우며 제작이 용이하기 때문에 이러한 장점을 이용하 면 저렴하고 다양한 용도의 충격마운트 제작에 효과적으로 사용될 수 있다. 본 논문에서는 원통형 콘테이너의 내충격 설계를 위해 충격사양에 의한 충 격마운트의 설계, 설계된 내충격 시스템의 충격시험에 의한 검증을 순차적으 로 실시하여, 방진고무를 이용한 충격마운트 설계기술을 제시함으로써, 이후 방진고무제품의 설계를 위한 자료 및 과정의 제정에 도움을 주고자 한다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2011년도 제42회 하계학술대회
• /
• pp.1497-1498
• /
• 2011

본 논문에서는 -50[$^{\circ}C$]환경에서 케이블 접속함의 극한지역 적용가능 여부를 확인하기 위해 접속함의 주재료인 Etylene Propylene Rubbe(EPR), Silicone Rubber(SR) 및 Epoxy의 물성 및 특성 평가 시험을 진행하였다. 실험방법은 DSC(Differential Scanning Calorimetry)를 사용하여 10[$^{\circ}C$]/min의 승온속도로 각각의 온도구간에서 샘플들의 Tg(Glass Transition Temperature)를 측정하였고, UTM(Universal Testing Machine)으로 -50[$^{\circ}C$]~ 상온에서 인장강도 및 신율을 측정하였다. 본 연구를 동하여, 극한지역의 전력계통 연계 안정성 및 신뢰성 향상을 위한 기초적인 Data-base를 구축했다.