• 대한기계학회논문집A
• /
• 제25권10호
• /
• pp.1590-1596
• /
• 2001

The shot peening process is most often used to improve fatigue properties of metal parts. The single most critical parameter of the shot peening process is the shot ball itself. Without the correct quality media, all other shut peening parameters are extraneous and the desired fatigue improvement and consistency of improvement will not be achieved. Shot peening involves modifications of the surface and subsurface condition of a material that can be described by the change of the residual stresses, the hardness, and the surface roughness. This Paper Presents the shot peening to optimize the shot ball parameters. The effect of shot peening parameter on the surface roughness, surface hardness and residual stress are investigated.

• 터널과지하공간
• /
• 제22권3호
• /
• pp.196-204
• /
• 2012

거칠기에 대한 정량화는 암석 절리의 강도 및 변형, 수리특성 등을 연구함에 있어서 매우 중요하다. 이 연구는 절리 거칠기를 모사하고 거칠기의 속성을 고찰하였다. 프랙털 파라미터와 프로파일 특성치를 입력변수로 설정하여 랜덤중점변위법에 기반한 이차원적 정상성 브라운 프로파일이 생성되었다. 또한, 랜덤중점변위법을 사용하여 삼차원적 거칠기 면을 모사하는 절차가 제시되었다. 이 연구의 거칠기 모사기법은 절리 거칠기와 관련된 해석적 연구를 수행하기 위한 요소 기술로 활용될 수 있다. 자기유사 거칠기 프로파일에 대하여 통계적 거칠기 파라미터를 적용한 결과 미소 거칠기의 기울기와 관련된 $Z_2$, $SL_{ave}$, $SD_{SL}$ 등의 통계적 파라미터는 상관구조, 진폭 등의 거칠기 속성을 고려할 수 있으나 측점간격의 변화에 영향을 받는 것으로 나타났다.

• 전기화학회지
• /
• 제6권3호
• /
• pp.217-223
• /
• 2003

The present work is concerned with characterization of surface roughness and inhomogeneity of four kinds of hot-rolled carbon steels in terms of the fractal dimension and the depression parameter by using image analysis method and electrochemical impedance spectroscopy, respectively. From the analysis of the 3D AFM image, it is realized that all the hot-rolled steel surfaces show the self-affine fractal property. The values of the fractal dimension of the hot-rolled steels were determined by the analyses of the AFM images on the basis of both the perimeter-area method and the triangulation method. In addition, the Nyquist plots were found to be depressed from a perfect semicircle form. From the experimental findings, the changes in the values of the fractal dimension and the depression parameter with chemical composition have been discussed in terms of the change in the value of hardness of base steel.

• 터널과지하공간
• /
• 제23권3호
• /
• pp.203-211
• /
• 2013

법선응력 수준과 초기 절리면 거칠기를 고려하여 절리면의 전단거동 특성을 고찰하였다. 절리면 전단강도는 순차적으로 법선응력을 증가시키는 다단계 전단시험을 수행하여 측정하였다. 일정한 법선응력 구간에서의 다단계 전단시험을 반복적으로 수행하여 전단파괴 기준선을 산출하였으며, 기준선의 순차적인 변화양상을 고찰하여 전단강도정수인 점착력과 마찰각의 2가지 변화 형태를 도출하였다: type 1 - 점착력 감소 및 마찰각 감소, type 2 - 점착력 감소 및 마찰각 증가. 편마암, 화강암 및 셰일의 3가지 암종별 전단강도정수 변화양상을 고찰하였으며, 순차적 전단거동 과정에서 절리면의 초기 거칠기가 전단강도 변화에 미치는 영향도 분석하였다.

• 한국세라믹학회지
• /
• 제50권2호
• /
• pp.122-126
• /
• 2013

The surface roughness of the inner and outer surfaces of a tube is an important requirement for nuclear fuel cladding. When an inner SiC clad tube, which is considered as an advanced Pressurized Water Cooled Reactor (PWR) clad with a three-layered structure, is fabricated by Chemical Vapor Deposition (CVD), the surface roughness of the substrate, graphite, is an important process parameter. The surface character of the graphite substrate could directly affect the roughness of the inner surface of SiC deposits, which is in contact with a substrate. To evaluate the effects of the surface roughness changes of a substrate, SiC deposits were fabricated using different types of graphite substrates prepared by the following four polishing paths and heat-treatment for purification: (1) polishing with #220 abrasive paper (PP) without heat treatment (HT), (2) polishing with #220 PP with HT, (3) #2400 PP without HT, (4) polishing with #2400 PP with HT. The average surface roughnesses (Ra) of each deposited SiC layer are 4.273, 6.599, 3.069, and $6.401{\mu}m$, respectively. In the low pressure SiC CVD process with a graphite substrate, the removal of graphite particles on the graphite surface during the purification and the temperature increasing process for CVD seemed to affect the surface roughness of SiC deposits. For the lower surface roughness of the as-deposited interlayer of SiC on the graphite substrate, the fine controlled processing with the completed removal of rough scratches and cleaning at each polishing and heat treating step was important.

• 한국기계가공학회지
• /
• 제20권8호
• /
• pp.93-98
• /
• 2021

The complex effects of the machining parameters make it is difficult to control and predict surface roughness. The theoretical surface roughness observed during mechanical machining with a round tool is determined by the tool radius and pitch. However, it was revealed that other parameters, such as the depth of cut and cutting speed, also affect surface roughness. This study adapted the Taguchi method, which can analyze the effects of cutting parameters quantitatively with an efficient number of experiments, to optimize the parameters for better surface roughness. Experiments were designed based on an orthogonal array, and the quantitative effects on the surface roughness were analyzed using the S/N ratio. The surface roughness was affected by all parameters, especially the tool radius. The optimum cutting parameter values obtained in this study showed better surface roughness than the other combinations of the parameters.

• 한국생산제조학회지
• /
• 제21권4호
• /
• pp.601-607
• /
• 2012

The magnetic abrasive polishing (MAP), for online monitoring with AE sensor attachment, was performed in this study. To predict the surface roughness after the magnetic abrasive polishing of NAK80, the signal data acquired from the AE sensor were analyzed. A dimensionless coefficient, which consisted of average of AErms and standard deviation of AE signal, was defined as a characteristic of the MAP and a prediction model was obtained using least square method. A neural network, which had multiple input parameters from AE signals and polishing conditions, was applied for predicting the surface roughness. As a result of this study, it was seen that there was very close correlation between the AE signal and the surface roughness in the MAP. And then on-line prediction of the surface roughness after the MAP of the NAK80 was possible by the developed prediction model.

• 한국정밀공학회지
• /
• 제18권8호
• /
• pp.139-149
• /
• 2001

The effects of the cutting conditions on the surface roughness of workpiece in turning were studied in this paper. The workpieces made of carbon steel SM20C and SM45C were tamed without the support of the tailstock center. Cutting conditions were changed in three or flour steps in each parameter and cutting fluid was used. The surface roughness results of tests were measured and the effects of the cutting conditions were analyzed by the method of analysis of variance. The summary of the experimental research is as follows. The main parameters were cutting speed, fred-rate, depth of cut, and the interactions between speed and fled-rate, speed and depth of cut, and fred and depth of cut. As cutting speed increased, surface roughness showed lower value. The surface roughnesses of feed-rate 0.102 mm/rev and 0.147 mm/rev were better than those of feed-rate 0.05 mm/rev and 0.2 mm/rev.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2001년도 추계학술대회 논문집
• /
• pp.106-110
• /
• 2001

The ball-end milling process is widely used in the die/mold industries, and it is very suitable for the machining of free-form surfaces. However, this process is inherently inefficient process to compared with the end-milling or face milling process, since it relays upon the machining at the cutter/surface contact point. The machined part is the result of continuous point-to-point machining on the free-form surface. And cusps (or scallops) remain at the machined part along the cutter paths and they give the geometrical roughness of the workpiece. Thus, for the good geometrical roughness of the workpiece, it is required very tightly spaced cutter paths in this ball-endmilling process. However, with the tight cutter paths, the geometrical roughness of the workpiece is not regular on the workpiece since the cusp height is variable in the previously developed ISO-parametric or Cartesian machining methods. This paper suggests a method of tool path generation which makes the geometrical roughness of workpiece be constant through the machined surface. In this method, Ferguson Surface design Model is used and cusp height is derived from the instantaneous curvatures. And, to have constant cusp height, an increment of parameter u or v is estimated along the reference cutter path. In ball-end milling experiments, the cusp pattern was examined, and it was proved that the geometrical roughness could be regular by suggested tool path generation method.

• 대기
• /
• 제25권2호
• /
• pp.339-351
• /
• 2015

The purpose of this study is for the fundamental understandings about building morphological parameters and aerodynamic roughness parameters of Seoul, Korea using the detailed urban geographic information datasets. Applied roughness parameter calculations are based on a digital map of buildings with lot area polygons. The quality of the developed roughness length ($z_0$) of Seoul was evaluated with densely installed 107 automatic weather stations. The correlation coefficient results between averaged wind speeds of AWS data and averaged $z_0$ is -0.303 in night and -0.398 in day (200 m radii circles case). Further $z_0$ enhancement should follow by considering other surface features such as high tree and orography of Seoul. However, this study would meet the needs to for local- or meso-scale meteorological modeling applications of Seoul. However, further studies would require for enhancing the $z_0$ applications of Seoul.