• Fibers and Polymers
• /
• v.7 no.4
• /
• pp.450-456
• /
• 2006

The objectives of this study were to investigate physiological and psychological responses to the rustling sound of Korean traditional silk fabrics and to figure out objective measurements such as sound parameters and mechanical properties determining the human responses. Five different traditional silk fabrics were selected by cluster analysis and their sound characteristics were observed in terms of FFT spectra and some calculated sound parameters including level pressure of total sound (LPT), Zwicker's psychoacoustic parameters - loudness(Z), sharpness(Z), roughness(Z), and fluctuation strength(Z), and sound color factors such as ${\Delta}L\;and\;{\Delta}f$. As physiological signals, the ratio of low frequency to high frequency (LF/HF) from the power spectrum of heart rate variability, pulse volume (PV), heart rate (HR), and skin conductance level (SCL) evoked by the fabric sounds were measured from thirty participants. Also, seven aspects of psychological state including softness, loudness, sharpness, roughness, clearness, highness, and pleasantness were evaluated when each sound was presented. The traditional silk fabric sounds were likely to be felt as soft and pleasant rather than clear and high, which seemed to evoke less change of both LF/HF and SCL indicating a negative sensation than other fabrics previously reported. As fluctuation strength(Z) were higher and bending rigidity (B) values lower, the fabrics tended to be perceived as sounding softer, which resulted in increase of PV changes. The higher LPT was concerned with higher rating for subjective loudness so that HR was more increased. Also, compression linearity (LC) affected subjective pleasantness positively, which caused less changes of HR. Therefore, we concluded that such objective measurements as LPT, fluctuation strength(Z), bending rigidity (B), and compression linearity (LC) were significant factors affecting physiological and psychological responses to the sounds of Korean traditional silk fabrics.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.16 no.4
• /
• pp.233-240
• /
• 2004

For the development of empirical equation of run-up height, a new surf parameter called' wave action slope' $S_x$ is introduced. Approximate equation has been produced for each band of water depth for the computation of wave run-up height using the laboratory graph of Saville(1958). On the other hand using the laboratory data of Ahrens(1988) and Mase(1989), empirical equations of run-up height have been developed for the general application with considering roughness effect covering a wide range of water depth and wall slope. When Mase tried to relate the run-up height to the Iribarren number, nonlinear relation has been obtained and hence the empirical equation has a power law. But when the wave action slope is adopted as a major factor for the estimation of run-up height the empirical equation shows a linear relationship with very good correlation for the wide range of water depth and wall slope.

• Journal of KSNVE
• /
• v.10 no.2
• /
• pp.345-352
• /
• 2000

Recently, it becomes to be very important to reduce the cabin noise of passenger ship, according to the trend of speedy and luxury ship. The noise reduction and control techniques should be considered as important factors from the viewpoint of the sound problem of cabin. Therefore, ship designer has to improve the sound quality as well as to redece the sound pressure level in cabins. In this paper, for the new approach of these problems, we tried to find the trends of noise and sound quality of high-speed coastal passenger ships. Loudness, roughness, fluctuation strength, and sharpness are selected as the parameters for the evaluation of sound quality. The parameters are calculated by using the sound measured in cabin while the ship is running. Furthermore we tried to find the trend of each parameter in cabins and compare with that of sound pressure level. As results, we find that the loudness is linearly proportional to sound pressure level. But, the other parameters show different trends which may be caused by ship motion on the wave and fluctuation of propelling power.

• Korean Journal of Materials Research
• /
• v.4 no.1
• /
• pp.31-36
• /
• 1994

The bonding behavior of $SiO_{2}$ thin film and glass during VCR head fabrication was investigated, varying the surface roughness of substrate and the sputtering parameter. Insufficient fillings of grooves In the $SiO_{2}$ film with glass was postulated to give rise to the generation of bubble in the glass. The surface roughness of $SiO_{2}$ film was found to depend on that of substrate. The lower the deposition rate, the smoother the surface of film. The bubble free glass after bonding could be obtained using substrate polished with 0.05$\mu\textrm{m}$ $Al_2O_3$ powder under the sputtering condition of 10% oxygen pressure.

• Wind and Structures
• /
• v.11 no.2
• /
• pp.75-96
• /
• 2008

A better understanding of tornado-induced wind loads is needed to improve the design of typical structures to resist these winds. An accurate understanding of the loads requires knowledge of near-ground tornado winds, but observations in this region are lacking. The first goal of this study was to verify how well a CFD model, when driven by far field radar observations and laboratory measurements, could capture the flow characteristics of both full scale and laboratory-simulated tornadoes. A second goal was to use the model to examine the sensitivity of the simulations to various parameters that might affect the laboratory simulator tornado. An understanding of near-ground winds in tornadoes will require coordinated efforts in both computational and physical simulation. The sensitivity of computational simulations of a tornado to geometric parameters and surface roughness within a domain based on the Iowa State University laboratory tornado simulator was investigated. In this study, CFD simulations of the flow field in a model domain that represents a laboratory tornado simulator were conducted using Doppler radar and laboratory velocity measurements as boundary conditions. The tornado was found to be sensitive to a variety of geometric parameters used in the numerical model. Increased surface roughness was found to reduce the tangential speed in the vortex near the ground and enlarge the core radius of the vortex. The core radius was a function of the swirl ratio while the peak tangential flow was a function of the magnitude of the total inflow velocity. The CFD simulations showed that it is possible to numerically simulate the surface winds of a tornado and control certain parameters of the laboratory simulator to influence the tornado characteristics of interest to engineers and match those of the field.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.17 no.2
• /
• pp.300-312
• /
• 1993

The material deterioration of service-exposed boiler tube steels in fossil power plant was evaluated by using the electrochemical technique namely, modified electrochemical potentiokinetic reactivation(EPR). It was focused that the passivation of Mo$_{6}$C carbide which governs the mechanical properties of Mo alloyed steels did not occur even in the passivity region of steel in sodium molybdate solution and the reactivation peak current (Ip) observed as the result of non-passivation indicating the precipitation of Mo$_{6}$C carbides. To obtain the optimal test conditions for the field test by using the specially designed electrochemical cell, the effects of scan rate, the surface roughness and the pH of electrolyte on Ip value were also investigated. Furthermore, the change of mechanical properties occurred during the long time exposure at high temperature was evlauated quantitatively by small punch(SP) tests and micro hardness test taking account of the metallurgical changes. It is known that reactivation peak current (Ip) has a good relationship with Larson-Miller Parameter(LMP) which represents the information about material deterioration occurred at high temperature environment. In addition it was possible to estimate the ductile-brittle transition temperature (DBTT) by means of the SP test. The Sp test could be, therefore, suggested as a reliable test method for evaluating the material degradation of boiler tube steels. From the good correaltion between the SP DBTT and Ip values shown in this study, it was knows that the change of mechanical properties could be evaluated non-destructively by measurring only Ip values.ues.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.35 no.4
• /
• pp.401-407
• /
• 2011

The conventional method of magnetic abrasive polishing is not suitable for non-magnetic materials because such polishing is basically possible when magnetic force exists and the magnetic force in non-magnetic materials is very low. The installation of an electromagnet under the working area of a non-magnetic material, which is called second-generation magnetic abrasive polishing in this study, can enhance the magnetic force. Experimental evaluation and optimization of process parameters for polishing magnesium alloy steel was performed by adopting the design of experiments and the response surface method. The results indicated that the intensity of the magnetic force and spindle speed are significant parameters that affect the improvement of surface roughness. A prediction model for the surface roughness of the magnesium alloy steel is developed using the second-order response surface method.

• The Journal of Engineering Geology
• /
• v.3 no.1
• /
• pp.1-20
• /
• 1993

In this study, laboratory direct shear tests on 37 core specimens of gneiss were performed to examine the characteristics of shear behavior on fractures by using a portable direct shear box. The multi-stage shear testing method was used and normal stress applied to specimens ranges from 5.60 to $25.67kg/\textrm{cm}^2$. On the basis of test results, the empirical equations for the shear strength on fractures were suggested. The methanical parameters that can influence the shear behavior were derived and compared between each parameter. The values of shear stiffness have a trend showing rapid increase with the increase of normal stress and joint roughness coeffident, and the average value of secant shear stiffness for all specimens is about $110.68kg/\textrm{cm}^3$ under the range of normal stress applied in this test In addition, the relationship between the length of specimen and shear stiffness is inversely correlated due to the size effect. Therefore, even the specimens with the same joint roughness coeffident show the trend of decreasing shear stiffness in case of the specimens being the longer length.

• The Journal of the Acoustical Society of Korea
• /
• v.36 no.1
• /
• pp.78-87
• /
• 2017

The goal of the present paper is to objectify the intrinsic subjectivity of sound as a media of music by applying psycho-acoustical methodology to the analysis of a musical work. First, 18 sound samples are extracted from "Symponie Fantastique" written by Hector Berlioz, which is a piece of program music, and then the objective Zwicher's sound quality parameters such as: Loudness, Sharpness, Roughness and Fluctuation Strength are evaluated for each of these sound samples. For subjective sound quality evaluation, 9 representative sound quality adjectives are extracted on a basis of program feature of Symponie Fantastique and the first jury test is carried out by using the numeric rating method and the paired comparison method. Three sound quality adjectives, "bright", "noisy", and "realistic" are extracted from the factor analysis of the first jury test result. On a basis of the computed sound metrics and the second jury test result for the three sound quality adjectives, three sound quality indexes are developed to represent the sound qualities of "Symponie Fantastique".

• Korean Journal of Metals and Materials
• /
• v.46 no.11
• /
• pp.747-754
• /
• 2008

Recently, the requirement for the ultra thin copper foil increases with smaller and miniaturized electronic components. Therefore, it is important to examine the surface state of substrate depending on the processing parameter during the anodic oxidation. This study investigated the effect of the various electrolyte concentrations on anodizing of titanium anode prior to copper electrodeposition. Different surface morphology of anodized titanium was obtained at different electrolytic concentration 0.5 M to 3.0 M. In addition, the effect that the surfaces and the electrical characteristics on the electrodeposited copper layer was observed. In this study, surface anodized in the group containing 0.5M $H_2SO_4$ shows more uniform copper crystals with low surface roughness. the surface roughness and sheet resistance for 0.5M $H_2SO_4$ group were $1.353{\mu}m$ and $0.104m{\Omega}/sq$, respectively.