• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제50권3호
• /
• pp.101-106
• /
• 2001

Air-cored superconducting synchronous generator(ASSG) is characterized by an air-cored machine with its rotor iron and stator iron teeth removed. For this reason, in the case of the shape optimum design of ASSG, other design variables different from an iron-cored machine should be considered, which will lead to substantial improvement on the performance. The major design variables that are considered by using Three-dimensional Finite element Method(3D FEM) in this paper are : 1) field coil width, 2) axial length of magnetic shield, and 3) armature winding method. End-ring of armature winding is considered in the calculation of EMF. When it comes to field coil width, as field coil width enlarges, its effective field increases but the maximum field on the superconductor decreases. this determines the critical current density. this study presents an effective field coil width, axial length of magnetic shield, and armature winding method, and also the analysis is verified by the experimental results.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2006년도 제37회 하계학술대회 논문집 B
• /
• pp.773-774
• /
• 2006

Nowadays, the global interests are concentrated on the preserving of the clean environment, and the diminishing of the dependence on the fossil energy, and among the possible alternative energies, the wind turbine generating system is considered to be the best suited to produce high efficiency energy, without affecting the natural environment. The permanent magnet generators were been used for the wind power generating, for long time, with continuous efforts to improve the generating efficiency. And the latest trend on it is to develop an AFPM(Axial Flux Permanent Magnet)type, which is composed in the structure of rotor and stator shaped in the disc forms, and the direction of the flux at the air gap runs in parallel to the shaft. This thesis is on the study concerning with the analysis of the characteristics of the 5 kW at 300rpm direct drive AFPM generator which is suitable for the small scale wind turbine generating system. In it, the Electro-magnetically Coreless AFPM was been analyzed, the prototype generators been made, concentrated on interpreting the characteristics of the power output, and verifying it through the theoretical study and practical tests.

• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제50권10호
• /
• pp.483-493
• /
• 2001

The 3-phase induction is used for the MCP(main coolant pump) and the pure water is used for lubrication of bearing because of the difficulty of repair. Therefore the type of motor is the canned-motor that is welded by sealed can to prevent the stator and rotor from the lubricating water. A lot of Eddy currents are produced in the can because of the conductivity of material. And these eddy currents in the can are the most important cause that decrease the efficiency of induction motor. Therefore we have to find the method to decrease these eddy currents in the can for the improvement of efficiency of motor. In this paper, we proposed the method of design and analysis of canned-motor using equivalent circuit with consideration of can loss for the improvement of efficiency of motor.

• International Journal of Fluid Machinery and Systems
• /
• 제4권1호
• /
• pp.199-208
• /
• 2011

This work presents numerical results, using OpenFOAM, of the flow in the swirl flow generator test rig developed at Politehnica University of Timisoara, Romania. The work shows results computed by solving the unsteady Reynolds Averaged Navier Stokes equations. The unsteady method couples the rotating and stationary parts using a sliding grid interface based on a GGI formulation. Turbulence is modeled using the standard k-${\varepsilon}$ model, and block structured wall function ICEM-Hexa meshes are used. The numerical results are validated against experimental LDV results, and against design velocity profiles. The investigation shows that OpenFOAM gives results that are comparable to the experimental and design profiles. The unsteady pressure fluctuations at four different positions in the draft tube is recorded. A Fourier analysis of the numerical results is compared whit that of the experimental values. The amplitude and frequency predicted by the numerical simulation are comparable to those given by the experimental results, though slightly over estimated.

• 한국조명전기설비학회지:조명전기설비
• /
• 제6권2호
• /
• pp.56-61
• /
• 1992

유도 전동기의 일정자속 벡터제어에서 유도전동기의 속도를 별도의 속도검출장치가 없이, 전동기의 속도를 1차측 전압과 전류 및 전동기정수에 의하여 추정하는 방법을 제시하고 전류추종형 PWM인 버터에 의하여 구동 시스템을 구성하였다. 모든 연산 및 제어회로를 마이크로프로세서에 의하여 보다 간단하게 실현시켜 유도전동기의 가변속 구동특성을 컴퓨터 시뮬레이션과 실험에 의하여 조사하였다. 속도검출장치를 이용한 경우와 연산회로에 의하여 계산된 경우의 입력 전류파형상의 차이를 조사한 결과 미소한 리플성분을 제외하고는 잘 일치하였으며, 기동 및 가감속시의 속도추종특성도 시뮬레이션의 결과와 함게 양호하게 얻어졌다.

• 한국정보통신학회논문지
• /
• 제5권2호
• /
• pp.315-320
• /
• 2001

본 논문은 뇌운의 접근에 따라 변화하는 대지전장 측정을 위하여 필드 밑을 이용한 대지전장 측정장치의 개발에 관하여 기술하였다. 필드 밀은 두 개의 절연된 전극으로 구성되며, 회전전극과 고정 전극이 있다. 고정도 필드 밀 개발을 위하여 회전형 필드 밀의 원리 및 설계기법에 관하여 연구하였으며, 교정실험장치로 원통형 가드전극계 및 평행평판 전극계의 두 가지 방법을 이용하여 주파수 대역 및 응답감도 특성을 조사하였다. 교정 실험결과로부터 주파수 대역 및 응답감도는 DC ~ 200(Hz), 0.267[mV/V/m]로 얻어졌으며 73[V/m] ~ 18.7[㎸/m] 범위의 대지전장 변화의 측정이 가능하다.

• 전기학회논문지P
• /
• 제57권2호
• /
• pp.121-126
• /
• 2008

This paper analyzes the losses of a Steinmetz connection three-phase induction motor which is supplied by a single-phase source. The T-type equivalent circuit which is taken no-load losses into account is used to determine phase converter capacitive reactances at starting and rated speed by using the condition of the minimum voltage unbalance. The starting and the operating capacitor are replaced at the slip of the same voltage unbalance factor points which are depicted using two capacitive reactances. The operation characteristics are investigated by comparing with those of three-phase balanced operation to find the feasibility of single-phase operation. To analyze the losses of this motor, the output power decrease factor(OPDF), the loss ratio(LR), the no load loss ratio(NLLR), the copper loss ratio(CLR), the stator copper loss ratio(SCLR), and the rotor copper loss ratio(RCLR) are defined and simulated in the whole slip range. The simulated results show that OPDF is maintained almost uniformly, LR is low at low speed and high at high speed, CLR is higher !ban NLLR, but CLR varies concavely and NLLR varies convexly at high speed, SCLR is low at low speed and high at high speed, but SCLR varies convexly at high speed, and RCLR is nearly opposite to SCLR.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2000년도 하계학술대회 논문집 B
• /
• pp.635-637
• /
• 2000

To analyze the transient state of an induction motor, there have been studies for using the magnetic equivalent circuit method (MECM) instead of the time differential finite-element method, MECM which analyzes magnetic equivalent circuits after converting each part of an electric machine into the magnetic circuit elements. has the merits of short calculation-time and comparatively accurate results. To analyze an electric machine with MECM, we have to replace stator and rotor with the magnetic elements and express the air gap, where electromechanical energy conversion takes place, with the permeance. So in this paper, to analyze an Induction Motor with MECM, we express the magnetic equivalent circuit as algebraic equations and then as the matrix for solving easily them.

• 한국기계가공학회지
• /
• 제9권5호
• /
• pp.76-82
• /
• 2010

In this study, we carried out to evaluate the shock-proof of a large scale motor for the naval vessel using dynamic design analysis method (DDAM) and full transient dynamic analysis. Analytical models for main assemblies (motor frame, rotor and stator assembly) were consisted of the tetrahedral solid elements and the equipments which installed in the upper side of the motor were substituted the mass elements. And we also modelled resilient mounts of a motor using the beam elements with appropriate directional stiffness. The DDAM was conducted according to NRL memorandum report 1396 and the full transient dynamic analysis was performed applying directional triple half triangle shock wave to the motor using ANSYS 12. As a result, we could compare of the results according to each analytic method and find the motor to satisfy the design criteria of the maximum stress and deformation.

• Journal of international Conference on Electrical Machines and Systems
• /
• 제1권1호
• /
• pp.32-39
• /
• 2012

With the aid of genetic algorithm (GA), global optimization with multiple geometry parameters is feasible in the design of switched flux permanent magnet (SFPM) machines. To investigate the advantages of global optimization over individual optimization, which has been used extensively for the design of SFPM machines, a comparison between the two approaches is carried out for the case of fixed copper loss and volume. In the case of individual parameter optimization, the sequence in which the individual parameters are optimized is very important. In the global optimization a better design can always be achieved although the corresponding torque density is found to be only slightly better than that of individually optimized with correct design sequence. By using the obtained global optimization results, the performance in machines having two types of stator and rotor pole combinations, i.e. 12/10 and 12/14, are compared, and it is shown that higher torque is exhibited in the 12/14 SFPM machine. Finally, this paper also demonstrates that global optimization, with the restriction of equal pole width, magnet thickness and slot opening, can maximize the torque density without significantly sacrificing other performance, such as cogging torque and overload capability.