• 한국염색가공학회지
• /
• 제22권3호
• /
• pp.187-193
• /
• 2010

The effects of molecular weight (MW) and concentration on the rheological properties of poly(vinyl alcohol) (PVA) solutions in dimethyl sulfoxide (DMSO) were investigated at $30^{\circ}C$. Ubbelohde viscometer and rotational rheometer were employed for dilute and concentrated regime, respectively. In the dilute regime, the Mark-Houwink exponent ($\alpha$) of the solutions determined from three different MWs proved 0.73. The critical concentration (C*), in which the entanglement and overlap of polymer molecules began to take place, decreased with increasing the MW of PVA. Huggins constant ($K_H$) values ranged from 0.33 to 0.45 over the MW examined. In the log-log plot of $\eta_{sp}$ versus [$\eta$]C, the PVA with higher degree of polymerization (DP) gave a greater slope exhibiting the inflection point in the vicinity of C*. In the dynamic viscosity ($\eta'$) curve, the PVA solutions of DP 1700 presented Newtonian fluid behavior over most of the frequency range examined. However, the lower Newtonian flow region reduced with increasing the DP. As the PVA concentration increased, $\eta'$ was increased and the onset shear rate for pseudoplasticity was decreased. In the Cole-Cole plot, PVA solutions showed almost a single master curve in a slope of ca. 1.65 regardless of the DP. However, the increase of the concentration from 8 to 12 wt% for PVA solutions of DP 5000 decreased the slope from 1.73 to 1.57. In the tan $\delta$ curve, the onset frequency for sol-gel transition was shifted from 154 to 92 rad/s with increasing the DP from 3300 to 5000 and from 192 to 46 rad/s with increasing the concentration from 8 to 12 wt%. In addition, longer relaxation time ($\lambda$) was observed with increasing the DP and concentration.

• 한국자동차공학회논문집
• /
• 제22권2호
• /
• pp.166-174
• /
• 2014

Fuel injection pressure has steadily increased in diesel engines for the purpose of improving fuel efficiency and cleaning exhaust gas, but it has now reached a point, where the cost for higher pressure does not warrant additional gains. Common rail systems on modern diesel engines have fuel pumps that are mechanically driven by crankshaft. The pumps actually house two pumping module inside: a low pressure pump component and a high pressure pump component. Part of the fuel compressed by the low pressure component returns to the tank in the process of maintaining the pressure in the common rail. Since the returning fuel represents pumping loss, fuel economy improves if the returned fuel can be eliminated by using a properly controled electrical fuel pump. As the first step in developing an electrical fuel pump the fuel supply system on a 6 liter diesel engine was modeled with AMESim to analyze the workload and the fuel feed rate of the injection pump, and the results served as basis for selecting a suitable servo motor and a reducer to drive the pump. A motor controller was built using a DSP and a program which controls the common rail pressure using a proportional control method based on the target fuel pressure information from the engine ECU. A test rig to evaluate performance of the fuel pump is implemented and used to show that the newly developed electrically driven fuel pump can satisfy the fuel flow demand of the engine under various operating conditions when the rotational speed of the pump is adequately controlled.

• 한국감성과학회:학술대회논문집
• /
• 한국감성과학회 2000년도 추계학술대회 논문집
• /
• pp.91-97
• /
• 2000

The conventional model did not take momentum conservation into consideration when the electron absorbs and emits the photons. II-ray provides momentum conservations on any directions of the entering photons, and also the electrons have radial momentum conservations and fully elastic bouncing between two atoms, in the new atom model. Conventional atom model must be criticized on the following four points. (1) Natural motions between positive and negative entities are not circular motions but linear going and returning ones, for examples sexual motion, tidal motion, day and night etc. Because the radius of hydrogen atom's electron orbit is the order of 10$^{-11}$ m and the radia of the nucleons in the nucleus are the order of 10$^{-l4}$m and then the converging n-gamma rays to the nucleus have so great circular momentum, the electron can not have a circular motion. We can say without doubt that any elementary mass particle can have only linear motion because of the n-rays' hindrances, near the nucleus. (2) Potential energy generation was neglected when electron changes its orbit from outer one to inner one. The h v is the kinetic energy of the photo-electron. The total energy difference between orbits comprises kinetic and potential energies. (3) The structure of the space must be taken into consideration because the properties of the electron do not change during the transition from outer orbit to inner one even though it produces photon. (4) Total energy conservation law applies to the energy flow between mind and matter because we daily experiences a interconnection between mind and body. An understanding of the mechanisms responsible for the control of normal proliferation and differentiation of the various cell types which make up the human body will undoubtedly allow a greater insight into the abnormal growth of cells, A large body of biochemical evidence was eventually used to generate a receptor model with an external ligand binding domain linked through a single trans-membrane domain to the cytoplasmic tyrosine kinase and autophosphory-lation domains. The ligand induced conformational change in the external domain generates either a push-pull or rotational signal which is transduced from the outside to the inside of cell.l.ell.

• 한국소음진동공학회논문집
• /
• 제25권7호
• /
• pp.487-495
• /
• 2015

A generalized special program called planetary transmission analysis(here in after PTA) is developed to improve planetary gear noise in automatic transmission. PTA is capable of analyzing any typical one-degree-of-freedom automatic transmission gear train containing any number of simple, compound or complex-compound planetary gear sets. The kinematics module in PTA can compute the rotational speeds of gears and carriers and calculate the order frequencies to predict the planetary noise components. The power flow analysis module performs a complete static force analysis providing forces, moments, or torques of gears, bearings, clutches and connections. Based on the given type and number of planetary gear sets, the search algorithm determines all possible kinematic configurations and gear tooth combinations in a required set of gear ratios, while eliminating whole kinematic redundancies and unfavorable clutching sequences. By using PTA program, planetary internal speeds of new developed automatic transmission are early obtained; therefore, possibility of the noise problem could be predicted in early design stage. As implementing PTA in planetary gear NVH development procedure, planetary gear noise was successfully reduced by 10 dBA.

• 한국정밀공학회지
• /
• 제28권10호
• /
• pp.1146-1152
• /
• 2011

Ink transfer process is very important to determine quality of printed pattern, therefore its mechanism should be understood to control printing quality. Although there have been many attempts to understand ink transfer mechanism by numerical simulation and experimental studies, their model was too much simple to model realistic printing process and our understanding is not enough yet. In this paper we designed ink transfer visualization system to present flow visualization of ink transfer process for gravure offset printing. We considered rotational effect of blanket roll which is related with printing speed and used non-Newtonian fluid as working fluid such as Ag paste. For printing unit, cantilever-type blanket roll is used for convenient visualization of ink transfer. Serial images were captured continuously by using high-speed CMOS camera and long range microscope. We investigated the effects of various design parameters such as printing speed and pattern angle on the ink transfer process. We found more stretched ink filament for non-Newtonian fluid than Newtonian fluid. As increasing printing speed, length of stretched ink filament and height of break-up point are also increased. We also compared ink transfer process between CD and MD pattern and its relationship with ink transfer mechanism.

• Tribology and Lubricants
• /
• 제36권5호
• /
• pp.253-261
• /
• 2020

In this paper, we present an experimental investigation of the frequency characteristics and a visual inspection of an oxidizer pump with a modified rear-floating ring seal for a 7-tonf turbopump. An oxidizer pump typically operates at high rotational speeds and under cryogenic conditions. Despite its low hydraulic efficiency, the floating ring seal is frequently employed as a leakage control solution for turbomachinery because it effectively reduces abrasion by friction. When the oxidizer pump starts up, the floating ring moves excursively but locks up stably against the pump casing when the contact pressure increases. The compressive force on the floating ring depends on the hydrodynamic forces induced by the flow through the floating ring. This force is controlled by the nose position of the floating ring. Based on a validation test for a 7-tonf turbopump with two types of floating rings, we concluded that the floating ring with a small diameter nose can move easily with a low contact pressure in the cooling path. This leads to instability of the pressure fluctuation around the floating ring. In contrast, a floating ring with a large diameter nose has a high contact pressure and attaches strongly to the casing, which causes wear and frictional oxidation between the contact surfaces of the impeller and the floating ring.

• 한국해양환경ㆍ에너지학회지
• /
• 제17권3호
• /
• pp.205-211
• /
• 2014

IMO에서 제시한 EEDI를 만족시키기 위해 에너지 절감 장치에 대한 관심이 증대되었다. 본 논문에서는 전류고정날개를 부착한 KVLCC2를 대상선으로 선정하여 에너지 절감 선박에 대해 연구하였다. 계산 결과의 정도를 검증하기 위해 모형선의 공칭반류를 모사하여 실험과 비교하였으며, 실선 스케일 계산에서는 격자 민감도에 대해 불확실성 평가를 하였다. 모형선과 실선 스케일 계산결과를 보면 전류고정날개는 추진기로 유입되는 반류의 회전성분을 변화시켜 추력에 도움을 주었다. ITTC에서 제시한 방법을 이용하여 실선의 성능을 예측해 보았으며, 이를 보안하는 방법을 제안하였다.

• 한국식품과학회지
• /
• 제16권1호
• /
• pp.11-16
• /
• 1984

멥쌀 및 찹쌀 전분을 상압과 가압가열 및 알칼리 호화한 회석전분 호화액에 대해 유동특성을 검토하였다. 전분농도 $0.2{\sim}1.0%$의 저농도의 호화전분액은 지수법칙 유체의 유동거동을 나타내었으며 아밀로오스 함량에 따라 크게 좌우되어 아밀로오스 함량이 많은 멥쌀은 점성이 낮고 뉴우톤 유체의 경향을 나타내었으며 농도에 대한 영향이 작았다. 찹쌀 전분은 농도가 증가함에 따라 의가소성 성질이 강해졌으며 농도에 따라 급격히 점도가 증가하였다. 가압호화시킨 경우 찹쌀 전분 호화액의 점조도 지수 및 유동 거동 지수는 상압 호화액에 비하여 거의 변화가 없었으나 멥쌀 전분 호화액의 점조도 지수값은 현저히 증가하는 현상을 보였다. 가압 가열호화 및 알칼리 호화 용액은 상압 가열호화에 비해 훨씬 높은 점성을 보였다. 가열 호화 및 알칼리호화액의 겉보기 점도에 대한 온도의 영향을 검토해 본 결과 아레니우스식의 형태에 따름을 알 수 있었다.

• 드라이브 ㆍ 컨트롤
• /
• 제17권3호
• /
• pp.26-32
• /
• 2020

In modern society, the energy-saving problem of industrial vehicles is economically and environmentally critical. Energy savings using the potential energy of forklifts are one of the viable solutions to resolving this problem. The basic concept of this study is to operate the hydraulic motor and recharge the battery using the flow rate from the cylinder when loading heavy objects and lowering the fork. To save energy, the torque and rotational speed of the generator should be optimized according to the load and descent speed to increase efficiency. To this end, we propose a system that optimizes energy saving efficiency by controlling the swashplate angle of the variable hydraulic motor through the GA(Genetic-Algorithm). The results were verified by building and comparing fixed motor models and variable motor models using the AMEsim. The results of the study show that the proposed optimized swashplate angle increases the energy saving efficiency by approximately 6%-8%, depending on the working conditions.

• 한국유체기계학회 논문집
• /
• 제18권6호
• /
• pp.45-56
• /
• 2015

This paper aims to develop a submerged propeller turbine for micro hydropower plant which allows to sustain high values of efficiency in a broad range of hydrological conditions (H=2~6 m, $Q=0.15{\sim}0.39m^3/s$). The two aspects to be considered in this development are mechanical simplicity and high-efficiency operation. Unlike conventional turbines that have spiral casing and gear box, this is directing driving and no spiral casing. A 10 kW class turbine which has the most high potential of the power generation has been developed. The most important element in the design of turbine is the runner blade. The initial blade is designed using inverse design method and then the runner geometry is modified by classical hydraulic method. The design process is carried out in two steps. First, the blade shape is fix and then other components of submerged propeller turbine are designed. Computational fluid dynamics analyses based on the Navier-Stokes equations have been used to obtain overall performance data for the blade and the full turbine, respectively. The results generated by performance parameters(head, guide vane opening angle and rotational speed) variations are theoretically analysed. The evaluation criteria for the blade and the turbine performances are the pressure distribution and flow's behavior on the runner blades and turbine. The results of simulation reveals an efficiency of 91.5% and power generation of 10.5kW at the best efficiency point at the head of 4m and a discharge of $0.3m^3/s$.