• 대한기계학회논문집A
• /
• 제40권1호
• /
• pp.41-51
• /
• 2016

볼나사 시스템은 볼과 그루브 사이에서 발생하는 마찰에 의해 온도가 상승하며, 이에 따른 열변형이 이송계의 위치결정 정도를 저하시킨다. 이를 보상하기 위해서는 볼나사 온도분포의 우선적 예측이 필요하다. 본 논문에서는 나사축 회전속도에 따른 온도분포를 해석하기 위해 볼나사 축과 너트를 각각 실린더와 중공 실린더로 가정한다. 경계조건인 대류 열전달계수, 볼과 그루브에서 발생하는 마찰토크와 접촉열전도를 볼나사 운전 및 조립 조건에 대하여 정식화 한다. 그리고, 현시적 유한차분법을 적용한 온도 분포 예측 시뮬레이터를 개발하고 그 유용성을 검증한다.

• Tribology and Lubricants
• /
• 제36권3호
• /
• pp.168-192
• /
• 2020

In recently designed diesel engines, the running conditions for piston-pin bearings have become severe because of the higher combustion pressure and increased temperature. Moreover, the metal removal from the bushing material has strongly reduced the ability of the antifriction material to accept asperity contacts. Therefore, it is necessary to find ways of reducing wear scar on the connecting-rod small-end bushing and piston-pin boss bearing related to the higher combustion pressure on the power cell of an engine. In this work, the position and level of material removal from the surfaces of the bushing and bearing under such severe operating conditions - for example, maximum power and torque conditions of a passenger car diesel engine - are estimated for several combinations of surface roughness. First, piston-pin rotating motion is investigated by calculating the friction coefficient at piston-pin bearings, the oil film thickness, and the frictional torques induced by hydrodynamic shear stress. Subsequently, the wear scarring on the surfaces of a connecting-rod small-end bushing and two piston-pin boss bearings related to piston-pin rotational motion is numerically calculated under the maximum power and torque operating conditions. This work is helpful to determine the reasonable surface roughness of the bushing and bearing for reducing wear volume occurring at the interface between a bearing and a shaft.

• 대한기계학회논문집A
• /
• 제38권6호
• /
• pp.609-617
• /
• 2014

풍력터빈 블레이드의 가변 피치제어는 풍력발전기의 과풍속 영역 설계에 있어 중요한 요소로 알려져 있으나 원가문제 때문에 소형 풍력터빈에는 적용되지 못하고 실속제어가 많이 적용되고 있다. 하지만, 블레이드 주변의 난류 때문에 설계된 실속이 구현되지 않는 실속지연 현상이 종종 발생되고, 이에 따른 풍력 블레이드의 과회전과 발전기의 과출력 위험이 발생하고 있다. 이에 따라 블레이드에서 발생되는 공력으로 피치가 변하고 스프링의 복원력으로 복귀되는 수동형 피치제어 모듈이 주목 받고 있다. 본 연구에서는 회전하는 블레이드의 익형에서 발생되는 양력과 항력을 이용하여 회전면으로 작용되는 토크와 블레이드의 Flap 방향으로 작용되는 추력을 계산하는 방법을 제시하고, 이러한 힘들의 크기를 여러 가지 익형에 대해 비교하였으며, 블레이드의 피치모멘트를 정량적으로 산출하여 수동 피치제어 모듈의 설계자료로 활용될 수 있도록 하였다.

• 한국기계가공학회지
• /
• 제19권1호
• /
• pp.89-99
• /
• 2020

This study analyzed the load and the consumed power characteristics of a potato harvesting operation in a dry field. The potato harvesting operation was performed using an underground crop harvester mounted on an agricultural tractor with a rated engine power of 23.7 kW. The rotational speeds and the torque of the engine output shaft, rear axle, and power take-off (PTO) shaft were measured under various working conditions. The load spectrum and the consumed power were analyzed using the measured data. The results show that the consumed power of the rear axle increased as the working speed increased, while that of the PTO shaft decreased. The consumed power of the engine output shaft showed a similar trend with that of the PTO shaft, but the torque deviation was larger in the load spectrum. The results of previous studies were used to compare herein the consumed power and the load characteristics of the harvesting, rotary, and plow operations in a dry field. PTO and tractive power were highly consumed in the plow and rotary operations, respectively. The consumed power of the PTO shaft and the rear axle in the harvesting operation were 29-41% and 18-23% of the engine power, respectively. Compared to those in the rotary and plow operations, the engine power was relatively evenly distributed to the PTO shaft and rear axle in the harvesting operation.

• 한국습지학회지
• /
• 제22권2호
• /
• pp.121-129
• /
• 2020

본 논문은 자유수면을 가지는 와류유동 내 저낙차에서 마이크로 소수력에 관한 실험 연구이다. 내부 곡선 모서리가 있는 직선, 곡선, 비틀린 블레이드의 와류 높이, 터빈 회전 및 토크를 개수로 유입구의 유량 0.0069 ㎥/s 조건에서 측정하였다. 실험결과로서 최적의 와류 강도는 와류 발생부의 외부직경과 유출구 직경 비율 0.17~18.5 범위에서 발생했다. 직선 블레이드 출력과 효율은 다른 블레이드와 비교하여 높게 나타났다. 가장 높게 생성된 에너지는 12.33 W이고, 토크는 0.91 N·m이다. 유효낙차를 고려한 경우 가장 높은 효율은 29.5 %인 반면 와류 높이를 고려한 가장 높은 효율은 회전수 132 rpm에서 80.5 %이다. 직선 블레이드의 와류 유속은 개수로 유입구의 평균 유속보다 약 2.8배 더 크게 나타난다.

• 농업과학연구
• /
• 제40권3호
• /
• pp.237-241
• /
• 2013

This study started to export an orchard tractor to Europe under the situations that R&D activities for orchard tractor were marginal and even it was not produced. The R&D for orchard tractor has been progressed and the most of it is accomplishing the goal. In this study, the durability of clutch friction part was tested for F/R clutch and moment of inertia of PTO clutch, and it was compared with the design criteria of transmission of tractor. According to the results of inertia test of F/R clutch, hydraulic pressures of clutch satisfied $1,961.33{\pm}196.13kPa$ of design criteria, and the variations of torque for forward and reverse operation were relatively constant. Therefore, it was found that the durability of clutch friction part was stable and reliable. Test results showed that the main hydraulic pressures were maintained $1,961.33{\pm}196.13kPa$ during the tests of moment of inertia of PTO clutch, and when it was operated, the hydraulic pressures were reached $1,961.33{\pm}196.13kPa$. Therefore, it was found that the hydraulic pressures of PTO satisfied the design criteria. By the results that the time of the hydraulic pressures of PTO reaching main hydraulic pressure, and that of torque values restoring to the original was same as the time of the first gear of PTO reaching the maximum rotational speed, it was found that PTO could transfer power to attachments as it was designed.

• 동력기계공학회지
• /
• 제15권5호
• /
• pp.10-15
• /
• 2011

This paper describes the engine performance and combustion characteristics of a CRDI diesel engine, operated by electronically controlled diesel fuel injector with variable injection timing. This experiment focused on fuel injection timing and pressure about combustion characteristics of CRDI diesel engine. EGR was excepted because it would be furtherly analyzed with additional experiments. The experiment was conducted under the circumstance of engine torque for 4, 8, 12 and 16 kgf-m and fuel injection timing for $15^{\circ}$, $10^{\circ}$ and $5^{\circ}$ BTDC, at the engine speed of 1100, 1400, 1700 and 2000 rpm. Fuel injection was controlled to retard or advance initiation of the injection event by electronically controlled fuel injection unit injector on the personal computer. When fuel was injected into the cylinders of a CRDI diesel engine it would go through ignition delay before starting of combustion. Therefore, fuel injection timing of CRDI diesel engine had a significant effect upon performance and combustion characteristics. Depending on the injection timing the fuel consumption rate following the rotational speed and torque was 3~78 g/psh (1.7~30.6%). The range of fuel injection timing that resulted in low fuel consumption overall was BTDC 15-10 degrees.

• 농업과학연구
• /
• 제48권4호
• /
• pp.1027-1037
• /
• 2021

This study aims to evaluate the performance of an electric multi-purpose cultivator through a simulation analysis. The simulation model was developed using commercial software, Simulation X, by applying the specifications of certain parts, such as an electric motor, a battery, and so on. The input parameter of the simulation was the engine load data according to the rotary tillage level using a conventional multi-purpose cultivator. The data were collected by configuring a load measurement system, and the load cycle was developed by repeating the data collection process under the most severe conditions. The average output engine torque values of conventional multi-purpose cultivator were 10.7, 13.0, 9.4, and 11.2 Nm in the D1P1, D1P2, D2P1, and D2P2 conditions, respectively. As a result of the simulation, the maximum values of the motor torque, rotational speed, and power of the electric multi-purpose cultivator were 16.8 Nm, 2,033.3 rpm, and 3.3 kW, respectively, and the motor was driven in sections within 70, 68, and 45% of the maximum output range. The rate of decrease of the battery state of charge (SOC) level per minute was approximately 0.6%, and it was possible to supply electric power to the motor for 9,550 sec. In the future study, research to verify and improve simulation models of electric multi-purpose cultivators should be conducted.

• Tribology and Lubricants
• /
• 제39권5호
• /
• pp.203-211
• /
• 2023

This study experimentally investigates the effects of angular acceleration on the friction and wear performances of a gas foil thrust bearing (GFTB) using a typical GFTB with six pads. The outer radius of the bearing is 31.5 mm, the total bearing area is 2,041 mm² , and the bump foil and incline (ramp) height are both 500 ㎛. The newly developed GFTB test rig for measuring the friction torque and coefficient measures the axial load, drag torque, lift-off speed, and touch-down speed. The experiment is conducted for angular accelerations of 78.5, 314.2, and 328.3 rad/s² at axial loads of 5, 10, and 15 N, respectively. The test shows that the start-up friction coefficient increases with increasing axial load at the same angular acceleration, and the friction coefficient decreases with increasing angular acceleration under the same axial load. As the angular acceleration increases, the lift-off speed at the motor start-up increases, and the touch-down speed at the motor stop decreases. The wear distance of the GFTB for a single on/off cycle increases with increasing axial load at the same angular acceleration and decreases nonlinearly with increasing angular acceleration under the same axial load. The test results suggest that adjusting the rotational angular acceleration helps reduce bearing friction and wear.

• 제어로봇시스템학회논문지
• /
• 제17권7호
• /
• pp.659-667
• /
• 2011

The study of bipedal robot is towards similar shape and function with human. In this paper, we propose a human-like walking pattern compatible to the flexible foot with toe and heel structure. The new walking pattern for a bipedal robot consists of ZMP, center of mass (CoM), and ankle trajectory and is drawn by considering human kinesiology. First, the ZMP trajectory moves forward without stopping at a point even in the single support phase. The corresponding CoM trajectory to the ZMP one is derived by solving differential equations. As well, a CoM trajectory for the vertical axis is added by following the idea of human motion. The ankle trajectory closely mimics the rotational motion of human ankles during taking off and landing on the ground. The advantages of the proposed walking pattern are demonstrated by showing improved stability, decreased ankle torque, and the longer step length capability. Specifically, it is interesting to know that the vertical CoM motion is able to compensate for the initial transient response.