• 대한기계학회논문집A
• /
• 제21권6호
• /
• pp.896-906
• /
• 1997

The effect of duplicate flexible disks on the vibrational modes of a flexible rotor system is investigated by using an anlytical method based on the assumed modes method. The rotor model to be analyzed consists of duplicate disks on a flexible shaft. In modeling the system, centrifugal stiffening and disk flexibility effects are taken into account. To demonstrate the effectiveness of the method, a hard disk drive spindle system commonly used in personal computers and a simple flexible rotor system with two disks are selected as examples. In particular, the dynamic coupling between the vibrational modes of the shaft and the duplicate disks is investigated with the shaft rotational speed varied.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 1997년도 추계학술대회논문집; 한국과학기술회관; 6 Nov. 1997
• /
• pp.101-109
• /
• 1997

An analytical procedure on the base of the substructure synthesis and assumed modes method is developed to investigate the flexibility effect of bladed disk assembly on vibrational modes of flexible rotor system. In modeling the system, Coriolis forces, gyroscopic moments, and centrifugal stiffening effects are taken into account. The coupled vibrations between the shaft and bladed disk are then extensively investigated through the numerical simulation of simplified models, with varying the shaft rotational speed and the pretwist and stagger angles of the blade. It is found that the Coriolis and inertia forces and the inertia torque, which are induced by the one nodal diameter modes of the bladed disk and vary depending upon the stagger and pretwist angles, lead to the coupled motions of the shaft and the bladed disk.

• 한국자동차공학회논문집
• /
• 제12권3호
• /
• pp.27-36
• /
• 2004

A Numerical analysis has been used to predict the performance in the automotive water pump with double discharge single suction. The influence of parameters such as coolant flow rate, rotational speed, ratio of blade height and clearance has been investigated. Also, the prediction of hydraulic performances such as static pressure rise, shaft power, hydraulic power and pump efficiency is carried out on the water pump including an impeller and a volute casing. A full size water pump test bench has been developed to validate the CFD flow model. Discharge flow rate, suction pressure, discharge pressure, rotational speed and torque measurements are provided. Coolant temperature is 8$0^{\circ}C$, water tank pressure is 1 kgf/$\textrm{cm}^2$ and flow rates vary.

• 한국정밀공학회지
• /
• 제30권7호
• /
• pp.694-701
• /
• 2013

The gear-reduction units of Korean high-speed trains consist of a motor reduction unit, an axle gear box reduction unit, and a tripod joint shaft. A reduction gear unit is a gearbox used to reduce the rotational speed of the input shaft to a slower rotational speed on the output shaft. This reduction in output speed helps to increase torque. Defective reduction gear units in high-speed trains are caused by damage to the gear or by gear fatigue. To diagnose potential problems, it is important to know the vibration characteristics of the reduction gear units. In this study, we analyzed the vibration characteristics of reduction gears under various conditions. The test setup included a full-scale test rig to evaluate reduction gear under both normal and extreme operating conditions.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 1999년도 추계학술대회 논문집 - 한국공작기계학회
• /
• pp.227-230
• /
• 1999

In this paper, the machining characteristics of high speed ball end milling affected by the rotational error of high speed spindle using air bearing are investigated. The error motions of a spindle have generally influenced on the surface roughness, the form accuracy, the tool life, etc. in end milling. Experiments are carried out over a wide range of rotational speeds(10,000-50,000rpm). The rotational errors of the spindle are measured by the gap sensor mounted on the spindle shaft at various cutting speeds. The relations between the surface roughness and the spindle error motion are presented. Results show that the rotational accuracy of the spindle directly affects the surface roughness of the machined surface.

• 한국정밀공학회지
• /
• 제11권1호
• /
• pp.63-70
• /
• 1994

This paper presents manufacturing and evaluation of a non-contact rotational torque measurement system which consists of torque cell, telemeter system, transmitter and receiver coil, transmitter, receiver and telemeter indicator. Static calibration test results show that the system has a maximum uncertaintry of 05% or less. A standar calibration system for rotational torque is used to evaluate the measurement system, As a result, the maximum uncertainty for measuring rotational torque by this system is 2% or less. We may conclude that the measurement system is sufficient to measure rotational torque of shaft in industry.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2011년도 제42회 하계학술대회
• /
• pp.93-94
• /
• 2011

This paper analyzes the shaft torsion of a doubly-fed induction generator (DFIG) for a wind farm collector system fault. When a fault occurs, the active power of the DFIG cannot be transmitted to the grid and thus accelerates the rotation of both the blade and the rotor. Due to the different inertia of these, the angle of deviation fluctuates and the shaft torsion is occurred. This becomes much severe when the rotational speed of the blade exceeds a threshold, which activating the pitch control to reduce the mechanical power. The torque, which can be sixty times larger than that in the steady state, may destroy the shaft. The shaft torsion phenomena are simulated using the EMTP-RV simulator. The results indicate that when a wind farm collector system fault occurs, a severe shaft torsion is occurred due to the activation of the pitch control.

• Tribology and Lubricants
• /
• 제11권5호
• /
• pp.40-46
• /
• 1995

This study concerns the design and development of the non-vibrating capacitance probe which could be used as a non-contact sensor for tribological wear. This device detects surface charge through temporal variation in the work function of a material. Experiments are performed to demonstrate the operation of the probe on a roating aluminum shaft. The reference electrode of the probe, made of lead, is placed adjacent (< 1.25-mm distance) to the shaft. Both surfaces which are electrically connected, form a capacitor. An artificial spatial variation in the work function is imposed on the shaft surface by coating a segment along the shaft circumference with a colloidal silver paint. As the shaft rotates, the reference electode senses changing contact potential difference with the shaft surface, owing to compositional variation. Temporal variation in the contact potential difference induces a current through the electrical connection. This current is amplified and converted to a voltage signal by an electoronic circuit with an operational amplifier. The magnitude of the signal decreases asymptotically with the electrode-shaft distance and increases linearly with the rotational frequency. These results are consistent with the theoretical model. Potential applications of the probe on wear monitoring are proposed.

• Journal of Biosystems Engineering
• /
• 제19권3호
• /
• pp.175-184
• /
• 1994

This study was conducted to investigate experimentally the basic characteristics of the torque of the cutterbar driving shaft as the double-knife was used instead of the conventional standard single-knife type. A new design for inclined setting of the cutterbar relative to the direction perpendicular to combine harvester movement was investigated to test a possible reduction of concentrated load caused by the simultaneous cutting of many rows. It was evaluated that the maximum torque and mean total power of the driving shaft due to the cutting resistance of the rice straw were largely depended upon the rotational shaft-speed and straw feeding rate, but were resepectively 1.1~2.3 and 1.15~1.34 times higher compared to those while idling. It was also proved that the inclined setting of the cutterbar could save a considerable amount of energy required for its driving shaft.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2002년도 proceedings of the second asia international conference on tribology
• /
• pp.125-127
• /
• 2002

This paper presents the measurement process of the rotational accuracy and the comparison with the theoretical results in the main bearing of scroll compressor. The main bearing is cylindrical oil proceeding bearing, but there are straightly cut used for oil supply. Therefore the roundness error is not a negligible quantity compared with the rotational accuracy. For this reason, three-point method is used in the experiment. The result of three-point method coincides with the theoretical value. So if the theory in this paper is used to the bearing design of scroll compressor, the efforts for testing and designing can be reduced.