• 전기의세계
• /
• v.18 no.4
• /
• pp.7-15
• /
• 1969

In this method the condenser excite winding has the phase angle of 90 electrical degree, with the load winding in stator. The condenser excite wing is connected with the condenser while the load winding is with the full rectifer. Direct and quardrature axis components of rotating field winding are composed, of balanced two phase winding, and each one of them is connected with half wave rectifiers. Initically, small amount of lead current can be induced at the condenser excite winding by residual magnetism of rotor. The induced lead current forces the rotating field winding to be excited by synchronous alternating magnetic field. The speed electromotive force, there for, induced in rotating field winding shall electro magnetize the rotating field pole by rotating half wave rectifiers. In the case of the charging generator directly coupled with engines at the operation of wide range speed, the generated region, such as vehicles, aircraft, ships etc, is occured. In conclusion, we can take the advantage of, omitting of voltage regurator and current limiter for charging load and reducing the consumption of fuel using the generated region which can be devided in to Impossible generated region, Generated region, and suspension generated region.

• International Journal of Automotive Technology
• /
• v.8 no.4
• /
• pp.521-531
• /
• 2007

Measurement of the vibration transmitted through rotating shafts such as half shafts in vehicles is of interest in applications such as noise transfer analysis and the study of operating deflections. Vibration signals transmitted through a rotating shaft usually include six degree-of-freedom components, thus making the measurement of vibration a challenging task. In the present work, a new measurement method is presented, one that resolves the minimum of only two one-axis accelerometer signals into all components of vibration with reasonable accuracy. The method utilizes the Dopplerized signals obtained from accelerometers attached to a rotating shaft and a Void-Kalman order tracking filter to decompose signals into orders of different vibration components. The new method proposed in the present work is verified by simulated run-up test data and applied to an experimentally obtained data set.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.11 no.3
• /
• pp.1650-1669
• /
• 2017

In this study, each pixel in an ear is used as a centroid to generate a cake. Subsequently the major axis length of this cake is computed and obtained. This obtained major axis length serves as a feature to recognize an ear. Later, the ear hole is used as a centroid and a 16-circle template is generated to extract the major axis lengths of the ear. The 16-circle template extracted signals are used to recognize an ear. In the next step, a ring-to-line mapping technique is used to map these major axis lengths to several straight-line signals. Next, the complex plane vector computing technique is used to determine the similarity of these major axis lengths, whereby a solution to the image-rotating problem is achieved. The aforementioned extracted signals are also compared to the ones that are extracted from its neighboring pixels, whereby solving the image-shifting problem. The algorithm developed in this study can precisely identify an ear image by solving the image rotation and image shifting problems.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2006.05a
• /
• pp.245-246
• /
• 2006

For developing 5-axis laser cutting systems, many problems such as rotating of laser head or table, 5-axis tool path generation and collision avoidance between laser head and product should be solved. In this paper, a five-axis laser cutting machine with table swivel and rotary type configuration is developed. The five axes (X,Y,Z,A,B) are controlled and interfaced to PC via MMC board. Two kinds of CAM S/W such as commercial 5-axis CAM S/W(Euclid) and UG-API are engaged to generate NC code for the developed 5-axis laser cutting machine.

• Journal of Korean Society of Industrial and Systems Engineering
• /
• v.34 no.3
• /
• pp.35-40
• /
• 2011

5-axis laser cutting has great advantages when it is applied to three dimensional machining requiring high cutting quality. For developing 5-axis CNC laser cutting systems, however, many problems such as rotating a laser head or a working table, 5-axis servo-control mechanism, tool path generation and post-processing, and collision avoidance between a laser head and a work-piece should be solved. In this paper, we deal with developing a motion simulator for 5-axis laser cutting machine with a nutating cutting head whose rotational axis is in an inclined plane. Two essential modules such as post-processor and cutting motion simulator was developed based on a commercial 3D CAD of UG-NX. The developed system was applied to three dimensional cutting products and showed the validity of the developed methods.

• Journal of the Korean Society for Precision Engineering
• /
• v.17 no.10
• /
• pp.83-88
• /
• 2000

multi-beam optical drive is a method to improve the data transfer rate for the optical disc systems by parallel recording and reading on neighboring multi-tracks. In this paper, the beam rotating actuator, which is necessary for the multi-bean optical disc drive to from beam spots on multi-tracks simultaneously, has been developed. The Voice Coil Motor is used as a drive mechanism for high resolution and small size of the actuator. And rotating guide based on link structure is designed for frictionless and axisless rotation of rotating part including dove prism and for rotating in axis of geometric center of dove prism. The characteristics of the actuator are experimented by laser vibrometer, Polytec OFV1102 and a dynamic analyzer, HP35670A. It shows that the actuator has good linearity, rotating range $\pm0.34^\circ$, minimum rotating angle $0.0066^\circ$and natural frequency 113.9Hz. Therefore the actuator can be applied in a multi-beam optical disc system.

• 한국신재생에너지학회:학술대회논문집
• /
• 2011.11a
• /
• pp.40.2-40.2
• /
• 2011

A Counter-rotating wind turbine is one of the new concepts that are proposed to increase the performance of a wind turbine. It has two rotors rotating in the same axis, and it is known that its power coefficient can reach to 0.64 in the ideal case. While the BEMT is widely used to analyze the aerodynamic performance of wind turbines, the analysis of the counter-rotating wind turbine by using it is limited due to the aerodynamic interaction between the two rotors. In this study, the vortex lattice method is used to consider the effect of the front rotor on the rear rotor of the counter-rotating wind turbine and calculate the aerodynamic performance of it. The power and thrust sharing in the two rotors of the counter-rotating wind turbine are predicted and the total power and thrust are compared with that of a single rotor. Moreover, the wake convection and expansion rate is also compared with that of a single rotor.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.8 no.4
• /
• pp.7-13
• /
• 2009

Five-axis laser cutting has great advantages when it is applied to 3-dimensional machining requiring high cutting quality. For developing 5-axis CNC laser cutting systems, however, many problems such as rotating a laser head or a working table, 5-axis servo-control mechanism, tool path generation and post processing, and collision avoidance between a laser head and a work-piece should be solved. In this paper, we deal with developing a dedicated CAM system based on UG-NX3 for 5-axis laser cutting machine. Two essential modules such as post-processor and cutting motion simulation was developed. The developed system was applied to cutting curve defined on 3-D workpiece in order to show the validity of the proposed methods.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.14 no.3
• /
• pp.16-22
• /
• 2005

It is difficult to separate those of NC controller from the error of machine tools because the conventional testing methods to inspect the performance are including the errors of moving system, therefore it has been used as the methods that compare the other controllers. Also, it is hard to predict the machine itself errors with the methods assembling the NC controller and moving system on machine because of the variable load conditions. In this study, the performance inspecting system was developed by analyse the $axis\_rotating$ properties of servo system finally outputting from NC controller. The axis torque was controlled by motor dynamometer and the rotating position accuracy was measured by this developed system.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2000.11a
• /
• pp.187-190
• /
• 2000

Cyclocopter is air vehicle to vertically take-off and land like a helicopter. This is an efficient and quiet means of being able to direct thrust compared to a helicopter. The rotor consists of several blades rotating about a horizontal axis perpendicular to the direction of normal flight. The direction of blade span is parallel to rotating axis and both end roots are connected to the hub to resist centrifugal force and to transmit the power. The pitch of the individual blades to the tangent of the circle of the blade's path is varied cyclically to gain thrust. In the paper, the design and manufactures of cyclocopter rotor blades are presented. Stress at the roots of cyclocopter blades is great due to centrifugal and aerodynamic forces and aeroelastic instabilities appear. The blades consist of main spar, front spar, polyurethan foam, weight, and skin and spars and skin are made of glass/epoxy composite.