• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2000년도 하계학술대회 논문집
• /
• pp.189-192
• /
• 2000

High-temperature superconductor of Bi-2212 system was fabricated by CFP(centrifugal forming process). To make a uniform specimen slurry was prepared in the ratio of 7:3(powder:binder) and ball milled for 24 hours. Milled slurry was charged into a rotating mold with 450 rpm and dried at room temperature. Then the specimen was performed binder burn-out at 35$0^{\circ}C$ and heated for partial melting to 86$0^{\circ}C$. XRD analysis of most specimens were shown 2212 phase and observed a local plate shaped microstructure with a well aligned c-axis direction from SEM images. T$_{c}$(Critical temperature) of Bi-2212 was 64K.K.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2008년도 춘계학술대회 논문집
• /
• pp.469-472
• /
• 2008

This research suggest one-body type scrapped styrofoam crusher with sprayed air (or water), which at present separately composed of dust eliminator, air supplier and crusher. Air (or water) that supplied from compressor injected to rotating twin roller through axis hole, and sprayed out of fine hole on the surface. The crusher that manufactured with sprayed air (or water) can make high-quality primary styrofoam removed pollution and dust. In case of mixed sprayed air and water, clean degree of crushed styrofoam was higher than single sprayed air. This could be contributed to reduce environmental pollution, cost and space in standpoint of recycling scrapped styrofoam.

• 한국소음진동공학회논문집
• /
• 제23권11호
• /
• pp.966-972
• /
• 2013

Measurement or estimation of tilt angle is necessary for balancing robot such as Segway which is considered as a next generation transportation vehicle. However, it requires high-cost accurate sensors to hold balancing during stationary and moving situations. In this paper, a tilt angle estimation of a plane rotating in a vertical plane using low-cost sensors. Estimation using a set of 2-axis orthogonal accelerometers along with an inaccurate rate gyro has been considered. Feasibility and performance of the proposed technique has been verified through some experimental results.

• 천문학회지
• /
• 제2권1호
• /
• pp.1-9
• /
• 1969

On the instantaneous tidal relaxation approximation, formulae are derived for the ellipticities and virial theorem of a slightly flattened homogeneous rotating cluster (the largest axis of the cluster is directed towards the Galactic center), in terms of the Galactic tidal force and the characteristic intrinsic plus orbital angular velocity. The expression for a purely tidally-determined ellipticity is identical to that for an incompressible fluid body of uniform density. Orbital motion generally contributes significantly to the shape of the cluster. The virial theorem is identical to that for an isolated cluster except that the gravitational potential energy is multiplied by (1-${\chi}$), where ${\chi}$ is a positive tidal correction term. To obtain the actual mass of a cluster, the virial theorem mass based on an isolated cluster should be multiplied by the factor 1/(1-${\chi}$). The formulae are applied to open star clusters, the globular cluster ${\omega}$ Centauri, and dwarf elliptical galaxies in the Local Group.

• 방사선산업학회지
• /
• 제7권2_3호
• /
• pp.201-207
• /
• 2013

Soil liquefaction by tsunami or wave induced currents can cause serious damages to coastlines and coastal infrastructures. Although liquefaction caused by regular waves over sea beds has been extensively investigated, studies of tsunami-induced liquefaction near coastal area have been relatively rare. In this work, the hydraulic scale model has been designed and constructed to investigate the variations of wave height and sediment transport by tsunami. The distorted hydraulic scale model based on the Froude similarity was adopted to represent hydrodynamics and sediment transport in a coastal area. The scale model was composed of control box, screw axis, wave paddle and rotating coastal structure.

• 한국반도체및디스플레이장비학회:학술대회논문집
• /
• 한국반도체및디스플레이장비학회 2003년도 춘계학술대회 발표 논문집
• /
• pp.80-87
• /
• 2003

On this study, an End-Effector for the 300mm wafer transfer robot System is newly suggested. It is a mechanical type with $180^{\circ}$ rotating ranges and is composed of 3-point arms, two plate springs and single-axis DC motor. It is controlled by microchip for the DC motor control. To design, relationships on the gripping force and the wafer deformation is analyzed by FEM analysis. Criterion on gripping force of a suggested End-Effector is confirmed as $255 ~ 274g_f$ from experimental results. From experimented results on repeatable position accuracy, gripping force and gripping cycle times in a wafer cleaning system, we confirmed that the suggested End-Effector is well satisfied on the required performance for 300mm wafer transfer robot system.

• Bulletin of the Korean Chemical Society
• /
• 제19권3호
• /
• pp.319-323
• /
• 1998

The phodissociation dynamics of t-butyl hydroperoxide at 280-285 nm has been investigated by measuring laser induced fluorescence spectra of the fragment OH. Measured fractions of the available energy distributed among the fragments are ft=0.56, fr(OH)=0.044, fint(t-BuO)=0.40, and negligible populations of OH are found in vibrationally excited states. By analyzing the Doppler profiles of the spectra of OH, the positive ν-J vector correlation has been obtained. From the measured ν-J correlation and A" propensity in the two Λ-doublets of OH, it is concluded that the dissociation takes place directly from the repulsive surface induced by the σ* ← n transition with the fragment OH rotating in the plane perpendicular to the dissociating O-O bond axis.

• 한국안광학회지
• /
• 제19권3호
• /
• pp.305-313
• /
• 2014

목적: 본 연구에서는 이심률에 따른 토릭소프트렌즈 피팅 시 회전방향 및 회전량과의 상관관계를 분석하였다. 방법: 20~30대 직난시 114안을 대상으로 제조사의 가이드라인을 기준과 피팅평가를 거쳐 적절한 토릭소프트렌즈를 착용하게 하고 정면주시할 때와 8개 방향으로 응시방향을 달리하였을 때의 회전방향 및 회전량을 각막이심률에 따라 비교 분석하였다. 귀쪽과 코쪽으로 각각 $45^{\circ}$회전시켰을 때의 회전 복귀속도 및 회전량과 각막이심률의 상관관계를 분석하였다. 결과: 각막이심률과 회전량은 양의 상관관계를 나타내었다. 응시방향의 경우 귀쪽과 코쪽으로의 응시방향을 제외한 나머지 응시방향에서 상관관계가 있는 것으로 나타났으며 그 중 위쪽과 귀위쪽 응시방향의 경우는 각막 이심률이 증가할수록 회전량은 감소하는 경향을 보였고, 이와는 반대로 아래쪽, 귀아래쪽, 코위쪽, 코아래쪽의 응시방향에서는 각막 이심률이 증가할수록 회전량도 증가하는 경향을 보여 응시방향에 따라 각막이심률과의 상관관계가 달리 나타남을 알 수 있었다. 회전복귀속도는 각막이심률이 가장 작은 군의 렌즈 복귀속도가 두 방향 모두에서 가장 빨랐지만 통계적으로 유의한 차이는 아니었다. 결론: 현재 전체난시만을 기준으로 처방되고 있는 토릭소프트렌즈의 피팅 기준에 각막이심률까지 고려한 피팅이 이루어진다면 최적의 축 안정화를 이루는데 도움이 될 것으로 보인다.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 1999년도 추계학술발표회 초록집
• /
• pp.15-15
• /
• 1999

In chip plating, several parameters must be taken into consideration. Current density, solution concentration, pH, solution temperature, components volume, chip and media ratio, barrel geometrical shape were most likely found to have an effect to the process yields. The 3 types of barrels utilized in chip plating industry are the conventional rotating barrel. vibrational barrel (vibarrel), and the centrifugal type. Conventional rotating barrel is a close type and is commonly used. The components inside the barrel are circulated by the barrel's rotation at a horizontal axis. Process yield has known to have higher thickness deviation. The vibrational barrel is an open type which offers a wide exposure to electrolyte resulting to a stable thickness deviation. It rotates in a vertical axis coupled with multi-vibration action to facilitate mixed up and easy transportation of components, The centrifugal barrel has its plated work centrifugally compacted against the cathode ring for superior electrical contact with simultaneous rotary motion. This experiment has determined the effect of barrel vibration intensity to the plating thickness distribution. The procedures carried out in the experiment involved the overall plating process., cleaning, rinse, Nickel plating, Tin-Lead plating. Plating time was adjusted to meet the required specification. All other parameters were maintained constant. Two trials were performed to confirm the consistency of the result. The thickness data of the experiment conducted showed that the average mean value obtained from higher vibrational intensity is nearer to the standard mean. The distribution curve shown has a narrower specification limits and it has a reduced variation around the target value, Generally, intensity control in vi-barrel facilitates mixed up and easy transportation of components, However, it is desirable to maintain an optimum vibration intensity to prevent solution intrusion into the chips' internal electrode. A cathodic reaction can occur in the interface of the external and internal electrode. $2HD{\;}+{\;}e{\;}{\rightarrow}20H{\;}+{\;}H_2$ Hydrogen can penetrate into the body and create pressure which can cause cracks. At high intensity, the chip's motion becomes stronger, its contact between each other is delayed and so plating action is being controlled. However, the strong impact created by its collision can damage the external electrode's structure thereby resulting to bad plating condition. 1 lot of chip was divided into two equal partion. Each portion was loaded to the same barrel one after the other. Nickel plating and tin-lead plating was performed in the same station. Portion A maintained the normal barrel vibration intensity and portion B vibration intensity was increased two steps higher. All other parameters, current, solution condition were maintained constant. Generally, plating method find procedures were carried out in a best way to maintained the best plating condition. After plating, samples were taken out from each portion. molded and polished. Plating thickness was investigated for both. To check consistency of results. 2nd trial was done now using different lot of another characteristics.

• 전력전자학회논문지
• /
• 제5권5호
• /
• pp.459-466
• /
• 2000

전정기관 자극용 회전자극기에 있어서 외란 관측기를 이용한 PMSM(permanent Magnet Synchronous Motor)의 강인한 정밀 속도 제어 방법에 대해서 제안한다. 본 제어기는 더욱 정확한 전정기관 평가를 가능하게 한다. 현기증을 유발시키기 위해서 지면에 수직인 회전축을 갖는 2D 자극기가 사용되어져 왔다. 그러나 정확한 현기증의 원인 규명을 위해서 회전축을 기울인 3D 자극기가 필요하다. 3D 자극기와 같이 기울임을 갖는 회 전자극기의 경우, 회전축에 대한 무게중심의 이격은 불평형 부하를 유발하게 된다. 이러한 경우에 대하여 강인한 속도 제어를 위한 외란 관측기를 이용하는 보상방법을 연구하였다 정확한 전정기관 자극을 위해 정밀한 속도 제어가 필요하며, 이러한 정밀 속도 제어에 있어서 외란의 영향을 제거하기 위해 데드비트 관측기와 같은 높은 이득을 갖는 관측기가 필요하다. 외란 관측기의 위치 제어에 대한 응용이 연구되어 졌다. 그러나 속도와 같은 노이즈가 많은 신호를 이용한 속도 제어에 있어서 데드비트 관측기는 노이즈 증폭 효과를 가져와 적용이 어렵다는 문제를 가지고 있다. 따라서 MA(Moving Average)처리를 이용하여 노이즈 효과를 저감한다. 이상의 제안된 알고리즘의 효과를 실험으로 보였다.