• 에너지공학
• /
• 제9권4호
• /
• pp.334-341
• /
• 2000

회전 히트파이프의 열 전달 특성은 내부 관벽에 형성되는 응축 액막 두께와 증발부로 귀한되는 응축액의 유동율에 의해 결정된다. 본 연구는 축 방향으로 그루브(groove)를 갖는 회전 히트파이프의 열 전달 성능에 대한 실험 연구로써, 그루브에 의한 효과를 파악하기 위해 2종류의 히트파이프를 제작하고 작동성은 시험을 수행하였다. 회전 히트파이프가 작동시, 원심력에 의해 그루브로 응축액의 유동을 촉진시키며, 따라서 응축부 벽면에 형성되는 액막 두께가 얇게 된다. 응축부에 그루브를 갖는 히트파이프의 열전달 계수는 풀 유동에서 2000~4000W/$m^2$$^{0}$ C, 환상 유동 영역에서 1500~2500W/$m^2$$^{0}$ C로써, 전체 원형단면을 갖는 히트파이프와 비교하여 약 1.5배 정도의 열저달 향상을 볼 수 있었으며, 열전달 한계는 약 40% 정도 향상되는 것으로 나타났다.

• 한국에너지공학회:학술대회논문집
• /
• 한국에너지공학회 1997년도 추계학술발표회 논문집
• /
• pp.114-121
• /
• 1997

회전 열파이프의 열전달 성능은 액막 두께 및 증발부로 귀환되는 응축 액막 유동율에 의해 결정된다. 그 동안 응축액 유동율을 촉진시키기 위하여 용기 내벽에 groove, 테이퍼 및 나선형 코일을 삽입하여 유동율을 높이는 방법들이 연구되었다. 본 연구도 회전 열파이프의 내부 관벽 구조에 관한 것으로써 삼각 단면을 갖는 회전 열파이프의 열전달 특성을 파악하고자 하였다. 삼각 단면을 갖는 회전 열파이프는 고속 회전 영역에서 모서리 부분으로 액막이 집중되어 관 내벽에 형성되는 액막 두께를 줄일 수 있으나 증발부에서 국부적인 과열이 발생되어 불안정한 작동 상태를 나타내었다. 따라서 본 연구에서는 개선방안으로 증발부에 부분적으로 원형관을 접합하였으며, 그 결과 dry-out의 억제와 함께 삼각 유동 단면에 의한 액막 두께 감소 효과를 볼 수 있었다. 회전체 발열부 냉각에 적용시키기 위해서는 앞으로 최적의 기하학적 형상에 따른 충전율 및 액막에서의 열전달에 대한 정량적인 해석 연구가 필요할 것으로 생각된다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2006년도 제37회 하계학술대회 논문집 B
• /
• pp.857-860
• /
• 2006

It is important to diminish noise source of an electric motor used in appliances. We studied on the noise reduction of BLDC motor to drive a fan. Especially, this study was focused on detent torque caused by interaction between a permanent magnet of rotor and groove in stator. This source and rotating system brought about a resonance. This paper showed that the higher harmonic component of this torque had a main factor to lessen noise. So, we had designed new magnets with shape like a peanut and pseudo-sinusoidal flux density for low-noise BLDC motor in refrigerator.

• 태양에너지
• /
• 제12권3호
• /
• pp.116-125
• /
• 1992

증발부를 접시형으로 하고 응축부를 나선형 그루우브로 하는 히이트파이프에서 움직이지 않는 경우와 회전을 하는 경우 입 열량에 따라 벽면과 증기의 온도분포를 구하여 전열특성을 연구하였다. 본 연구에 사용된 히이트파이프는 단순 히이트파이프보다 우수한 전열특성을 가지며, 히이트파이프의 열전달은 입열량과 회전수가 증가하면 증가하였다.

• 에너지공학
• /
• 제8권2호
• /
• pp.325-332
• /
• 1999

회전 히트파이프가 작동할 때 응축 액막은 중력과 원심력에 의해 관 내벽을 따라 응축부에서 증발부로 이송된다. 회전 히트파이프의 성능은 응축 액막의 두께와 응축 액막 유동율에 의해 좌우된다. 따라서 기존의 많은 연구자들은 회전 히트파이프의 성능을 향상시키기 위하여 테이퍼, 계단식 벽면, 코일 삽입등 관 내부의 형상에 대한 연구를 수행하였다. 본 연구에서는 회전 히트파이프의 새로운 관 내벽 형상으로써 응축부에 축 방향으로 사각 그루브(groove)를 갖는 구조이다. 히트파이프가 회전하면 원심력에 의해 응축 액막이 그루브로 유동하며 따라서 응축부의 전체적인 액막 두께를 감소시킬 수 있다. 실험 결과 그루브에 의한 액막 유동 효과로써 열전달 계수가 향상되었다. 또한 응축 액막 유동 해석 결과는 본 실험치와 정량적으로 다소 차이를 나타내었으나 회전수 및 열속 변화에 대하여 정성적으로 유사한 경향을 나타내었다.

• 한국공작기계학회논문집
• /
• 제13권3호
• /
• pp.53-60
• /
• 2004

We have developed and manufactured an experimental ultrasonic polishing machine with frequency of 20kHz at the power of vibration 1.7㎾ for effective ultrasonic polishing in processing of high hardness material. Design of the horn is performed by the FEM analysis. The following conclusions were empirically deduced through experimental results to clarify the major elements which affect the surface roughness during the ultrasonic process by following the experimental plans. The ultrasonic polishing machine has been developed in parts of structure part, ultrasonic generator, vibrator. We were able to process the high hardness material without difficulty as a result of ultrasonic polishing by utilizing the groove added step-type horn. Through analyzing by applying the experimental plans, the rotating speed of the horn was determined to be the major factor in influencing the surface roughness. In the case of ceramic, wafer, we were able to obtain good surface roughness when the feed rate and the ultrasonic output were higher. Because the load on slurry particle increases when the ultrasonic output is higher, the processed surface becomes worse in the case of optical glass.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2005년도 춘계학술대회 논문집
• /
• pp.796-805
• /
• 2005

The tilting pad journal bearings have been widely used to support high pressure/high rotating turbine rotors owing to their inherent dynamic stability characteristics. However, fatigue damages in the upper unloaded pads and the break of locking pins etc. by pad fluttering are continuously taken place in the actual steam turbines. The purpose of this paper is to develop a new bearing model that can prevent bearing problems effectively by pad fluttering in a tilting pad journal bearing. A new bearing model which has a wedged groove is suggested from the studies of fluttering mechanism performed by previously research works. The fluttering characteristics of the upper unloaded pad are studied experimentally in order to verify the reliability of a new bearing model. It can be known that the phenomenon of pad fluttering nearly does not occurred in the new bearing model under the various experimental conditions. And it is observed that any kinds of bearing failures by pad fluttering does not detect in the application of acture steam turbines.

• 한국유체기계학회 논문집
• /
• 제8권5호
• /
• pp.35-45
• /
• 2005

The tilting pad journal bearings have been widely used to support high pressure/high rotating turbine rotors owing to their inherent dynamic stability characteristics. However, fatigue damages in the upper unloaded pads and the break of locking pins etc. by pad fluttering are continuously taken place in the actual steam turbines. The purpose of this paper is to develop a new bearing model that can prevent bearing problems effectively by pad fluttering in a tilting pad journal bearing. A new bearing model which has a wedged groove is suggested from the studies of fluttering mechanism performed by previously research works. The fluttering characteristics of the upper unloaded pad are studied experimentally in order to verify the reliability of a new bearing model. It can be known that the phenomenon of pad fluttering nearly does not occurred in the new bearing model under the various experimental conditions. And it is observed that any kinds of bearing failures by pad fluttering does not detect in the application of acture steam turbines.

• 드라이브 ㆍ 컨트롤
• /
• 제16권4호
• /
• pp.87-92
• /
• 2019

Rotary dampers are damping devices which provide high resistance to shaft rotation. Rotary dampers are being used in various areas to enable the gentle opening and closing of the rotation motion relative to home furniture, industry machinery and automotive parts. Rotary dampers can be installed directly at the rotating point of a various part and can achieve uniform, gentle movement which increases quality and value of products. And generally, the silicone fluid is used as the damping medium because of its stable viscous properties. The movement of these little decelerators can be achieved with a high viscosity of working fluid and throttles installed in the body of the rotary damper. The damping force can be achieved clockwise, anti-clockwise or in both directions according to the structure of the orifices or throttles. In this paper, the torque performances of the rotary damper containing air in the working fluid were studied. For this purpose, the torque characteristic of the rotary damper according to the variation of various operating conditions such as clearance of leakage, dimensions of groove orifice, content ratio of air, etc., were simulated with AMEsim software.

• 한국임상수의학회지
• /
• 제16권2호
• /
• pp.300-308
• /
• 1999

Arthroscopy is a valuable diagnostic and operative tool in equine and human orthopedics. The arthroscope is a difficult instrument to use and requires patience, practice, and persistence in order to obtain good results. This technique was found to be less traumatic than arthrotomy, invasiveness, rapid recovery and the feasibility of surgically correcting many arthropathies. The use of the arthroscope in the dog provides a new dimension in the study and diagnosis of joint derangements. The purpose of this report is to introduce the use of the arthroscope in the dog-more specifically, in the stifle of the dog. A diameter 2.7 mm fore-oblique viewing arthroscope, cold light source, video and video printer are used. With the fore-oblique viewing type it is possible to view directly as well as slightly to the side and the range of viewing can be increased by rotating the arthroscope around the object The scope is connected with a cold light source by means of a fiber-optic light guide. The stifle joint was flexed to 20~30$^{\circ}$. The joint were lavaged with lactated Ringer's solution during arthroscopic examination. Arthroscopy of the stifle was performed prior to arthrotomy in 1 dead dog and 4 healthy dogs, and other 3 dogs was performed only arthroscopic examination. In this study only the conventional approaches were used and in most cases it was possible to view all the intra-articular structures via the lateral infrapatellar approach. In the stifle joint, endoscopic observation was performed to find lateral femoral condyle, patella, medial femoral condyle, trochlear groove, tibia, fat, cranial cruciate ligament, caudal cruciate ligament lateral meniscus, tendon of long digital extensor muscle, medial meniscus, and medial collateral ligament Post-arthroscopic examination, the lameness had disappeared within 12~24 hours. Pain and swelling in the stifle joint had disappeared within 24~36 hours. Post-arthroscopic secondary infection was never encountered in the dogs. In conclusion, arthroscopic insertion technique in canine stifle joint using a diameter 2.7 mm 30$^{\circ}$ arthroscope was established and arthroscopical views of all anatomical structures in the normal stilfe joint were obtained through lateral infrapatellar portal.