• Nuclear Engineering and Technology
• /
• v.52 no.4
• /
• pp.776-783
• /
• 2020

As the refueling of a sodium-cooled fast reactor is conducted by rotating part of the reactor head without opening it, the monitoring of existing obstacles that can disturb the rotation of the reactor head is one of the most important issues. This paper deals with the ultrasonic ranging technique that directly monitors the existence of possible obstacles located in a lateral gap between the upper internal structure and the reactor core in a prototype generation IV sodium-cooled fast reactor (PGSFR). A 10 m long plate-type ultrasonic waveguide sensor, whose feasibility has been successfully demonstrated through preliminary tests, was employed for the ultrasonic ranging technique. The design of the sensor's wave radiating section was modified to improve the radiation performance, and the radiated field was investigated through beam profile measurements. A test facility simulating the lower part of the upper internal structure and the upper part of the reactor core with the same shapes and sizes as those in the PGSFR was newly constructed. Several under-water performance tests were then carried out at room temperature to investigate the applicability of the developed ranging technique using the plate-type ultrasonic waveguide sensor with the actual geometry of the PGSFR's internal structures.

• Proceedings of the KIEE Conference
• /
• 1998.07d
• /
• pp.1549-1551
• /
• 1998

We have designed and developed narrow bandpass multipole filters for satellite communication using $YBa_2Cu_3O_{7-x}$(YBCO) thin films on MgO substrates. The superconducting film used in this study was prepared by laser ablation on one side polished MgO (100) substrates. A Nd:YAG laser was used to fabricate YBCO thin films. The wave length of the laser was 355 nm. The laser beam was focused onto a YBCO target rotating linearly to avoid deep craters that may eject macroscopic YBCO particles. The YBCO films were grown at $750^{\circ}C$ in the oxygen partial pressure of 200 mTorr. The deposited YBCO thin films were patterned by conventional wet-etching method. The transition temperatures of YBCO thin films were 85 - 88 K and the film thicknesses were about 5,000 $\AA$. By comparing the performances of normal-metal filters and YBCO filters, we observed that superconducting YBCO multipole filters have been showed superior performances at 77 K.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.23 no.3
• /
• pp.245-249
• /
• 2010

Two dimensional(2D) pair-photonic crystals (pair-PCs) have been fabricated by a multiple-exposure nanosphere lithography (MENSL) method using the self-assembled nanospheres as lens-mask patterns and the collimated laser beam as a multiple-exposing source. The arrays of the 2D pair-PCs exhibited variable lattice structures and shape the control of rotating angle (${\Theta}$), tilting angle (${\gamma}$) and the exposure conditions. In addition, the base period or filling factor of pair-PCs as well as their shapes could be changed by experimental conditions and nanosphere size. A 1.18-${\mu}m$-thick resist was spincoated on Si substrate and the multiple exposure was carried out at change of ${\gamma}$ and ${\Theta}$. Images of prepared 2D pair-PCs were observed by SEM. We believe that the MENSL method is a suitable useful tool to realize the pair-periodic arrays of large area.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.46 no.7
• /
• pp.1-5
• /
• 2009

Random beanforming exploits multiuser diversity gain in static channels. Since the gain is restricted by the user population, some extended works have been proposed. Among them, a codebook-based opportunistic beamforming technique forms multiple random beams with small pilots. The technique however has difficulty in designing beams flexibly by the channel statistics. In this paper, we propose a technique forming the multiple random beams by rotating codebooks. The proposed technique enables the flexible design of beams so that multiuser diversity and beam selection diversity are exploited simultaneously with small pilots robust to the channel statistics.

• Proceedings of the Korean Society of Medical Physics Conference
• /
• 2002.09a
• /
• pp.376-378
• /
• 2002

This work was carried out to evaluate the basic performances for 4D CT, which employed continuously rotating conebeam. The performances were evaluated with the same method as the conventional CT, because the standard method of evaluating 4D CT has not yet been established, and we think this result was helpful to establish it. 4D CT can give dynamic volume imaging data continuously and with high-speed. The results were isotropic except for the evaluation of distortion in which small distortions gradually appeared as coming off the center of phantom in longitudinal direction.

• Journal of ILASS-Korea
• /
• v.5 no.1
• /
• pp.49-57
• /
• 2000

This study presents the flow visualization results, velocity and turbulence intensity measurements made within an air filter cover and entry region of a mass air flow sensor (MAFS) which is used in an induction system of 3.8L engine. Flow structure in two air filter cover assemblies were examined. The first was a clear plastic replica of the production cover while the second was a modified clear plastic cover with a geometry configured to reduce fluctuations. High speed flow visualization and laser doppler velocimetry (LDV) systems were used to reveal and analyze the flow field characteristics encountered in the sensor design process under steady flow conditions. A 40-watt copper vapor laser was used as a light source. Its beam is focused down to a sheet of light approximately 1.5mm thick. The light scattered off the particles was recorded by a 16mm high speed rotating prism camera at 5000 frames per second. A comparison of the flow patterns and LDV measurements in the original and modified air filter covers is presented to illustrate the controlling effect of the cover design on the turbulence structure formation near the bypass and on the sensor output signal. In both axial and radial planes of the main passage it was found that the turbulence flow pattern is remarkably influenced by the air filter cover and main passage configuration.

• Korean Journal of Optics and Photonics
• /
• v.15 no.4
• /
• pp.309-312
• /
• 2004

Two-dimensionally arrayed nanocolumn lattices were fabricated by using double-exposure laser holographic method. The hexagonal lattice was formed by rotating the sample with 60 degree while the square lattice by 90 degree before the second laser-exposure. The size and period of nanocolumns could be controlled accurately from 125 to 145 nm in diameter and 220 to 290 nm in period for square lattice by changing the incident angle of laser beam. The reactive ion etching for a typical time of 30 min using CH$_4$/H$_2$ plasma enhanced the aspect-ratio by more than 1.5 with a slight increase of the bottom width of columns.

• Transactions of Materials Processing
• /
• v.19 no.5
• /
• pp.277-282
• /
• 2010

Magnesium alloy has been known as lightweight material in automobile and electronic industry with aluminum alloy, titanium alloy and plastic material. Friction welding is useful to join various metals and nonferrous metals that are difficult to join by such as gas welding, resistance welding and electronic beam welding. In this study, friction joining was performed to investigate mechanical properties of Mg alloy with 20mm diameter solid bar. Also the optimal joining conditions for its application were determined on the basis of tensile test, and hardness survey. The joining parameters were chosen as heating pressure, heating time, upsetting pressure, and upsetting time. Heating and upsetting pressure were executed under the range of 10~40MPa and 20~80MPa, respectively. From the experimental results, optimal joining conditions were determined as follows; rotating speed=2000rpm, heating pressure=35MPa, upsetting pressure=70MPa, heating time=1sec, upsetting time=5sec. Also the hardness of jointed boundary showed as HV50 which was similar to that of base metal at the optimal condition, and it was supposed that zone of HAZ was 8mm. Finally two materials were strongly mixed at interface part to show a well-combined microstructure without particle growth or any defect.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.17 no.2 s.119
• /
• pp.105-113
• /
• 2007

In this study, three-dimensional rotordynamic analyses have been conducted using equivalent beam, hybrid and full three-dimensional models. The present computational method is based on the general finite element method with rotating gyroscopic effects of the rotor system. General purpose commercial finite element code, SAMCEF which includes practical rotordynamics module with various types of rotor analysis tools and bearing elements is applied. For the purpose of numerical verification, comparison study for a benchmark rotor model with support bearings is performed first. Detailed finite element models based on three different modeling concepts are constructed and then computational analyses are conducted for the realistic and complex three-dimensional rotor system. The results for rotor stability and mass unbalance response are presented and compared with the experimental vibration test data conducted herein.

• Laser Solutions
• /
• v.12 no.1
• /
• pp.25-33
• /
• 2009

In laser-assisted machining (LAM), laser beam is used to locally increase the temperature of a workpiece and thus to enhance the machinability. In order to set the temperature of the material removal area of a workpiece at an optimal value, process parameters, such as laser power, feed rate, and rotational velocity, have to be carefully controlled. In this work, the effects of laser power and feed rate on the temperature distribution of a silicon nitride rotating at a constant velocity were experimentally investigated. Using a pyrometer, temperatures at various locations of the silicon nitride were measured both in circumferential and axial directions. The measured temperatures were fitted to a quadratic equation to approximate the temperature at the cutting location. The machining results showed that cutting force and tool wear were decreased when the temperature at the cutting location was increased.