• Transactions of the Korean Society of Automotive Engineers
• /
• v.5 no.6
• /
• pp.148-154
• /
• 1997

The safety problems of buses have been arisen due to the increasing of road traffic. Occupant injuries are always possible in the rollover accident and the frontal impact. Thus the structure of bus should have sufficient strength to protect passengers under accidental loads. ECE(Economic Commission for Europe) regulation No.66 prescribes that the superstructure of the vehicle shall be sufficient strength for passengers' surviving and the residual space shall be preserved in the passenger compartment during and after the standard rollover accident situation. Rollover test and simulation on a large-sized bus was completed according to the regulation. The coordinates of the points on the bus were measured by photogrammetry system. The rollover situation was revived by structural crashes simulation software, PAM-CRASH, and it was checked that the structure still complied with the requirements of residual space during rollover situation. The residual space was preserved during rollover, so it was proved that the structure of the investigated bus had much probability of survival in rollover accidents.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.18 no.2
• /
• pp.31-38
• /
• 2010

Bus manufacturers have tested and studied the dynamic collapse behavior of a bus body structure in rollover since UN ECE established ECE Regulation 66 to provide the requirement for the strength of bus structure. In spite of the costly cycles of practical tests, however, it is still a hard task to meet the rollover regulation by means of local reinforcements in the bus structure. Therefore it is necessary to develop a well designed strategy for the rollover strength implemented in the early stage of vehicle development. In this study, the suitable development method for each design stage from a component to complete body structure was considered to make a well-established development process of a bus body structure for rollover safety. For the efficient approach of the concept design stage, a numerical model based on the plastic hinge theory was used instead of detailed shell models. After setting up the concept design for the component size and geometry, the shell model was used to confirm and optimize the whole structure composition. The process developed in this study was practically used as an effective method to predict the rollover behavior of a new bus body structure.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.5 no.6
• /
• pp.28-35
• /
• 1997

Occupant injuries are always possible in a rollover accident, one of the major accidents in a bus. Thus the structure of body frame should have sufficient strength to protect passengers under accidental loads,. ECE(Economic Commission for Europe) regulation No.66 prescribes that residual space shall be preserved in the passenger compartment during and after the structure has been subjected to the prescribed rollover test. Rollover test on a bus section was completed according to the regulation. The coordinates of body section before and after rollover were measured, and it was checked that the structure still complied with the requirements of residual space. Direct measurement on a bus is difficult because of its large size. Thus photogrammetry by photographing and 3 dimensional digital modeling was introduced, and the coordinates of each point were measured through this method.

• Journal of Drive and Control
• /
• v.19 no.3
• /
• pp.39-46
• /
• 2022

In South Korea, to evaluate the rollover safety of domestic vehicles, the maximum slope angle of the vehicle is specified, which is verified by the rollover safety test of driving vehicles. However, the domestic rollover safety test is not suitable for buses, because the small amount of static stability factor (SSF) will invalidate the rollover experimental equation due to the high center of mass position of buses. To solve the above problems, a dynamic model of the bus is prepared with assumptions of mass and suspension spring properties. Subsequently, the maximum slope angle of the model was computed by using the simulation of multi-body dynamics, and the result was compared with actual test results to validate the dynamics model. Also, the rollover Fishhook (roll stability) test was conducted in the simulation for driving model. During the simulation, roll angle and roll rate were calculated to check if a rollover occurred. Through the rollover simulation of buses, the domestically regulated formula for rollover safety and the procedure of rollover test for driving vehicles are evaluated. The conclusion is that the present regulation of rollover test should be reconsidered for buses to ensure to get the valid results for rollover safety.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.19 no.3
• /
• pp.113-121
• /
• 2011

Rollover accident is one of the serious traffic accident and rollover accident takes high portion of all accident. The most common type of rollover is a tripped rollover which occupy 95% of all type of single-vehicle rollover. Tripped rollover occurs when a vehicle leaves normal road way and tripped by loose gravel, soil of fixed object such as guard rail, curbs and ditches. And the rest of the type of rollover is un-tripped rollover. An un-tripped rollovers that occurs during high-speed collision avoidance maneuvers. In this paper, presents the explanation of the un-tripped rollover test method and procedure, additionally this paper deals with various occurrence in the un-tripped test such as occurring excessive tire camber in the un-tripped test, tire side-wall contact with road surface and roll oscillation. And this paper analyzes the analysis of the roll rate amplitude in specific frequency through the FFT (Fast Fourier Transform) and the roll angle at the steering reverse timing which is the Fishhook test roll rate feedback time. Finally, this paper analyzes the relations between the estimated steady state roll gain and rollover stability.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.15 no.1
• /
• pp.56-63
• /
• 2007

In case of bus rollover, the body structure of the bus should be designed to ensure the survival space for passengers. So, this study focuses on evaluating rollover strength through a computer simulation using the commercial code, LS-DYNA3D at the initial stage of vehicle development. For this study, section structure was modeled using a simple beam element, and impact boundary conditions required by ECE(Economic Commission for Europe) regulation No.66 were applied. In order to confirm the validity of the beam element bus model, the results compared with the test results and shell element bus model. The analysis errors from beam element bus model are due to the difference in strain energy of joint area between beam and shell model. In this study, a method for the joint modeling was suggested by using nonlinear springs to which the collapse mechanisms were applied.

• Journal of Auto-vehicle Safety Association
• /
• v.13 no.4
• /
• pp.66-72
• /
• 2021

This study was initiated to improve of the defect investigation method using event data recorders (EDR) and suggested a solution through the regulation and system analysis of EDR. The EDR data has been used for various purposes such as the vehicle defect investigation and the traffic accident investigation. However the EDR regulation has not been updated since the implementation in 2012. "Trigger Threshold" can be used to analyze a single accident such as the frontal crash, the side crash, and the rollover. In the case of a complex accident in which a rollover accident and a crash accident occur simultaneously, it is difficult to analyze a complex accident due to current "Trigger Threshold". This study proposed the method of separating the "Trigger Threshold" into a crash accident and a rollover accident so that accidents can be analyzed using the EDR data even when a complex accident occurs. In addition, it proposed the improvement method to quickly use the data of EDR in accident reconstruction software.

• Journal of Auto-vehicle Safety Association
• /
• v.13 no.3
• /
• pp.47-53
• /
• 2021

This study is a study to estimate the VSL (Value of a Statistical Life) and CBA (Cost-benefit analysis) of the rollover safety standard for hydrogen buses, VSL is an economic value concept used to quantify the benefits of avoiding death. CBA shows the effect of cost-benefit, and if B/C is greater than 1, there is a social effect. In order to estimate the VSL and CBA, the hydrogen bus introduction scenario was assumed to be optimistic (20,000 vehicles in 2030), neutral (15,000 vehicles in 2030), and pessimistic (10,000 vehicles in 2030), and the effect of reducing human casualties was estimated. As a result, except for the pessimistic market situation of introducing hydrogen buses (10,000 vehicles in 2030) and the VSL reduction ratio of 10%, all policies were judged to have high cost-benefit effects. These results indicate that the introduction of the rollover safety standard for hydrogen buses is a socially effective policy.

• Journal of Auto-vehicle Safety Association
• /
• v.12 no.3
• /
• pp.52-60
• /
• 2020

Usage of EDR(Event Data Recorder) report for traffic accident analysis is currently increasing due to government regulation of EDR data release. Nevertheless, a lot of investigators simply adopt by comparing the number of ignition cycles(crash) at event to the number of ignition cycles(download) without an exact judgment whether event data occurred by this accident or not. In the EDR report, besides ignition cycles, there are many factors such as event record type, algorithm active(rear/rollover/side/frontal), time between events, event severity status(rollover/rear/right side/reft side/frontal), belt switch circuit status, driver/passenger pretensioner/air-bag deployment, PDOF(Principal Direction of Force) by ΔV to be able to decide whether or not to adopt. also the event data is considered enough to vehicle damaged state, accident situation at the scene of the accident. and there is described in "all data should be examined in conjunction with other available physical evidence from the vehicle and scene" in the CDR(Crash Data Retrieval) report. Therefore many investigators have to decide whether or not to adopt after they consider sufficiently to above factors when they are the traffic accident analysis and investigate the causes of a accident on the adopted event data. In this paper, we report to traffic accident investigators notable points and analysis methods on the basis of thousands of cases and the results of one's own experiment in NFS(National Forensic Service).