• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.11 no.12
• /
• pp.4715-4720
• /
• 2010

In this study, we developed new tapered rolling type strip pressure key for the prevention of scratch in sheet metal forming line. The developed pressure key is equipped with two tapered rollers inside a conventional block pressure key. Through the scratch test, for the case of transversal movement the tapered rolling type pressure key reduces both friction and depth of scratch by the effect of tapered shape which decreases the pressure spike on edge, and for longitudinal movement the scratch on the sheet metal surface is certainly removed by the rolling contact.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.6 no.3
• /
• pp.58-64
• /
• 2007

The clamping force of a jaw pad is determined by the displacements of main part when two lockers are locked, after the clamping angle of a locker was set up in the wedge type rail clamp for a container crane. In this time, if the resistance of wedge frame generates due to several factors, the clamping angle of a locker to display the initial clamping force will be changed because of the reduction of displacement of extension bar. This resistance is determined by the eccentric distance between the roller and the wedge, and by the gap between the wedge frame and outer frame. In this study we measured the tensile force of both extension bar through the performance test of the prototype rail clamp in order to evaluate the effect of the resistance of wedge frame on the clamping force of the wedge type rail clamp.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2002.10a
• /
• pp.599-602
• /
• 2002

A novel rapid prototyping (RP) process, an automated transfer type variable lamination manufacturing process (Automated VLM-ST) has been developed. In Automated VLM-ST, a vacuum chuck and linear moving system transfer the plate type material with two pilot holes to the rotation stage. A four-axis synchronized hotwire cutter cuts the material twice to generate Automated Unit Shape Layer (AUSL) with the desired width, side slopes, length, and two reference shapes in accordance with CAD data. Each AUSL is stacked on the stacking plate with two pilot pins using the pilot holes in AUSL and the pilot pins. Subsequently, adhesive is supplied to the top surface of the stacked AUSL by a bonding roller and pressure is simultaneously applied to the bottom surface of the stacked AUSL. Finally, three-dimensional shapes are rapidly fabricated. This paper describes the procedure for generating the cutting path data (AUSL data) f3r automated VLM-ST. The method for the generation of the Automated Unit Shape Layer (AUSL) in Automated VLM-ST was practically applied and fabricated for a various shapes.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.21 no.8
• /
• pp.752-760
• /
• 2011

In tilting pad bearing design process, the selection of the proper configuration type of either a load-between-pad(LBP) or load-on-pad(LOP) as well as preload and pivot offset conditions is to be carefully considered. Also the bearing needs to be designed in order to be suited for the rotor-bearing system and operating condition. In this paper, it is observed that the dynamic characteristics in a five pad tilting pad bearing for the LBP and the LOP configurations are influenced by the variation of preload and pivot offset. In this context, rotor dynamic analysis of the 5 MW industrial gas turbine supported by the tilting pad bearing at the front and roller bearing at the rear is carried out based on the dynamic coefficients of the tilting pad bearing investigated. The result shows that two rigid body critical modes experience various changes according to the influence of the tilting pad bearing uniquely applied to one side of this machine. Mainly, the second critical speed, the rigid body mode of conical shape with high whirling in the tilting pad bearing, is significantly changed by preload and pivot offset regardless of the LBP and LOP configurations. And, the first critical mode, the rigid body mode of conical shape with high whirling in the roller bearing, is sensitively affected by preload applied to the LOP configuration and by its asymmetric dynamic properties.

• Tribology and Lubricants
• /
• v.34 no.2
• /
• pp.55-59
• /
• 2018

This paper proposes a new type of electro-mechanical wedge brake for commercial vehicles. The brake operates on a novel mechanism for self-boosting braking friction forces using eccentric shafts, and involves wedges that are inserted between the rampbridge and traverse; this self-boosting mechanism is explained herein. A dynamic analysis using ADAMS was conducted, and the findings are reported. The constraint and contact conditions are explained to verify the precision of the dynamic analysis. The dynamic analysis shows that in the proposed mechanism, the self-boosting effect occurs as desired. However, it is also noted that the system has a limitation in terms of the production of unlimited braking forces that can jam the roller inside the wedges. After demonstrating the self-boosting effect, dynamic analyses are performed for several values of the wedge angles and friction coefficients between the brake pads and disks. Conventionally, a lower wedge angle has been suggested owing to its provision of a larger clamping force for given friction coefficients. However, it is noted that lower wedge angles can lead to a higher probability of occurrence of undesirable high braking forces, which can jam the roller into the wedge; thus, a larger wedge angle is preferable for avoiding the undesirable jamming phenomena. These analysis results are presented and discussed herein.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2011.04a
• /
• pp.425-432
• /
• 2011

In tilting pad bearing design process, the selection of the proper configuration type of either a Load-Between-Pad (LBP) or Load-On-Pad (LOP) as well as preload and pivot offset conditions is to be carefully considered. Also the bearing needs to be designed in order to be suited for the rotor-bearing system and operating condition. In this paper, it is observed that the dynamic characteristics in a 5 pad tilting pad bearing for the LBP and the LOP configurations are influenced by the variation of preload and pivot offset. In this context, rotor dynamic analysis of the 5MW industrial gas turbine supported by the tilting pad bearing at the front and roller bearing at the rear is carried out based on the dynamic coefficients of the tilting pad bearing investigated. The result shows that two rigid body critical modes experience various changes according to the influence of the tilting pad bearing uniquely applied to one side of this machine. Mainly, the second critical speed, the rigid body mode of conical shape with high whirling in the tilting pad bearing, is significantly changed by preload and pivot offset regardless of the LBP and LOP configurations. And, the first critical mode, the rigid body mode of conical shape with high whirling in the roller bearing, is sensitively affected by preload applied to the LOP configuration and by the its asymmetric dynamic properties.

• Journal of Ship and Ocean Technology
• /
• v.6 no.3
• /
• pp.1-12
• /
• 2002

In this paper the results are reported of sixty-nine lateral collision tests, which were performed to investigate the collision resistance of plates. For the tests a collision testing machine of spring-roller conveyer type was designed and fabricated. Using this machine, various plates were tested with different masses and velocities and various headers of the striker. A simple analytical method has also been developed to predict the extent of damage of struck plates due to lateral collision. In the method, it is assumed that the kinetic energy of the striker can be dissipated by the formation of yield lines and membrane tensions in the impacted plate. The calculated predictions of extent of damage using the developed method have been substantiated with the test results, which shows reasonably acceptable correlations.

• International Journal of Aerospace System Engineering
• /
• v.1 no.1
• /
• pp.16-20
• /
• 2014

Recently, various kinds of study on light weight structure are performing in the world. The Al honeycomb sandwich structural type adopt for improvement of lightness and structural stability to major part structure of aircraft or spacecraft. Adhesion badness properties of adhesive and adhesion properties of fillet mainly studied about al honeycomb structure. But study for adhesive properties of sandwich construction with surface treatment of Aluminum alloy barely performed. In this study, adhesive film was used between Al and honeycomb core of honeycomb panel[1]. The study for adhesive properties of sandwich construction with surface treatment of AA 5052 skin was performed.

• Proceedings of the KIPE Conference
• /
• 2003.07a
• /
• pp.110-114
• /
• 2003

In this paper, a new self-oscillated type high voltage charger controller circuit is proposed, which has variable constant current source characteristics to improve charge characteristic of charger roller. The proposed control method enables high quality printing characteristics regardless of the circumstance change such as ambient temperature or humidity by changing the current reference signal. To verify the proposed control method various experiments are performed.

• Journal of the korean Society of Automotive Engineers
• /
• v.3 no.3
• /
• pp.30-38
• /
• 1981

The fatigue characteristics of Si-Mn spring steel (AISI 9260-H, JIS SUP-6) were investigated on several heat treatment conditions. Repeated impact loads of 10kg-cm and 15kg-cm energy were applied with a cam roller drop hammer type impact fatigue testing machine. Specimens were oil-quenched, and tempered at 350.deg. C, 450.deg. C and 500.deg. C, respectively. Results obtained in these experiments are summarized as follows.; 1) The fatigue life of the specimen is decreased as the magnitude of constant impact energy is increased, regardless of heat treatment. 2) Generally, the fatigue life of the specimen is decreased as the tensile strength of the materials is increased. 3) Within the limit of these experiments, the fatigue life showed abrupt decrease at the tempering temperature of about 400.deg. C 4) The fatigue life is increased as the initial value of applied stress intensity factor(K$_{1}$) is decreased. This tendency is apparent for the low tensile strength materials.