• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.08a
• /
• pp.125-125
• /
• 2011

In this study, we investigated the electrical, optical, structural, and surface properties of indium zinc oxide (IZO)/Ag/IZO multilayer electrode grown by specially designed roll-to-roll sputtering system using the flexible substrate. By the continuous roll-to-roll sputtering of the bottom IZO, Ag, and top IZO layers at room temperature, they were able to fabricate a high quality IZO/Ag/IZO multilayer electrode. At optimized conditions, the bottom IZO layer (40 nm) was deposited on a flexible substrate. After deposition of the Bottom IZO layer, Ag layer was deposited onto the bottom IZO film as a function of DC power (200~500 W). Subsequently, the top IZO layer was deposited onto the Ag layer at identical deposition conditions to the bottom IZO layer (40 nm). We investigated the characteristics of IZO/Ag/IZO multilayer electrode as a function of Ag thickness. It was found that the electrical and optical properties of IZO/Ag/IZO multilayer electrode was mainly affected thickness of the Ag layer at optimized condition. In case of IZO/Ag/IZO multilayer electrode with the Ag power (350W), it exhibited a low sheet resistance of 7.1 ohm/square and a high transparency of 86.4%. Furthermore, we fabricated the touch screen panel using the IZO/Ag/IZO multilayer electrode, which demonstrate the possibility of the IZO/Ag/IZO multilayer electrode grown by roll-to-roll sputtering system as a transparent conducting layer in the touch screen panel.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.11a
• /
• pp.380-381
• /
• 2007

This paper reports on the deposition conditions and properties of ITO films used as electrode layer in a organic light emitting diodes on a PET substrate. The deposition technique employed was specially designed roll-to-roll sputtering. The oxide was deposited at room temperature in an argon and oxygen plasma on a transparent conducting ITO layer on a PET film. The influence of deposition parameters such as DC power, working pressure and oxygen partial pressure has been investigated, in order to obtain the best compromise between a high deposition rate and adequate electro-optical properties. Electrical and optical properties of ITO films were analyzed by Hall measurement examinations with van der pauw geometry at room temperature and UV/Vis spectrometer analysis, respectively. In addition, the structural properties and surface smoothness were measured by x-ray diffraction and scaning electron microscopy, respectively. From optimized ITO films grown by roll-to-roll sputter system, good electrical$(6.44{\times}10^{-4}\;{\Omega}-cm)$ and optical(above 86 % at 550 nm) properties were obtained. Also, the ITO films exhibited amorphous structure and very flat surface beacause of low deposition temperature.

• Journal of Institute of Control, Robotics and Systems
• /
• v.5 no.3
• /
• pp.370-378
• /
• 1999

KOMPSAT is a three-axis stabilized light weight satellite, and one of the main mission objectives of the KOMPSAT is to conduct scientific and technological analysis in the areas of high resolution imaging and ocean color imaging. This kind of mission requires the satellite to roll up to 45 degrees. Bang-bang control for this rolling maneuver may activate the flexible modes, and therefore cause satellite pointing performance degradation. To deal with this problem, the roll attitude control system, especially for the science mode and maneuver mode of the KOMPSAT, is first verified by numerical simulation. And the open-loop control law for roll maneuver is proposed by use of series expansion and optimization. The proposed control law is applied to KOMPSAT to see its effectiveness.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.8 no.5
• /
• pp.207-215
• /
• 2000

This study theoretically investigated the roll-off cleanliness operation to eliminate the built-in contaminants which are primarily the result of manufacturing and assembly procedures first. A rigorous analytical examination of the cleaning process associated with hydraulic systems was performed by developing the general filtration process equations. The sloughing process by which built-in contaminant is entrained in the system fluid was examined during the development of a general analytical expression for sloughing rate. This sloughing rate expression in conjunction with the filtration process equations have lead to a relationship rate expression in conjunction with the filtration process equations have lead to a relationship which describes the flushing and clean-up operation for the hydraulic systems. The effects of the primary roll-off cleanliness factors was discussed and illustrated on the figures. Then, the analytical results was shown to be usefully applied into the design of roll-off flushing equipment for the hydraulic system of a tractor.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.19 no.5
• /
• pp.22-28
• /
• 2011

This paper presents an active roll motion control of a passenger vehicle. The roll controller is designed in the framework of $H_{\infty}$ control scheme based on the 3 DOF vehicle model taking into consideration parameter variations, which affect the roll dynamics, and unmodeled high frequency dynamics for robustness and performance. In order to investigate the feasibility of the active roll control system in a car, its performance is evaluated by simulation in a full vehicle model with nonlinear tire characteristics under various operating conditions. Finally, in order to enhance the performance in a transient region taking into account the limited bandwidth of the actuating module, a hybrid control strategy is presented.

• Journal of the Semiconductor & Display Technology
• /
• v.9 no.2
• /
• pp.73-78
• /
• 2010

This research is about the drying and curing characteristic of conductivity metallic ink on-line curing device in order to improve the curing time for productivity in RFID Gravure printing. The curing process is carried out to increase the electric conductivity after the metallic ink is printed on the substrate. The metal ink is composed of nano-sized silver or copper particles. In this research, the combined IR and Hot air curing system is used and its results is compared with those of oven, IR and Hot Air type respectively. Generally the curing time in the past is about 3 minutes. But the combined system (IR+Hot Air) in this research shows that curing time is less than 30 seconds. These results is much faster than those of other system. This study can be help to make Roll-to-Roll drying and curing process for mass and continuous production on-line.

• Proceedings of the KSME Conference
• /
• 2007.05a
• /
• pp.461-466
• /
• 2007

There has been a great interest in printing technology as a low cost and mass production method for the application of printed electronics such as printed TFT, solar cell, RFID Tag, printed battery, and so on. In this study, apparatuses of gravure-offset printing are developed for fine line-width/gap printing and examining pattern distortion occurred in gravure-offset printing process. The fine line-width/gap pattern shows that it is possible to make around 20 micro-meter line-width/gap printing patterns. Pattern distortion is modeled, and the amount and shape of the distortion are calculated by using commercial FEM code. The roll-to-roll printing system under development consists of unwinder/rewinder, two printing units, one coating unit, drying units, guiding unit, vision system, and other auxiliary devices. For multi-layer printing, the system is designed to be capable of printing two different materials.

• Laser Solutions
• /
• v.13 no.2
• /
• pp.6-9
• /
• 2010

In printed electronics, printing rolls are used to transfer electronic ink onto a flexible substrate. Generally printing rolls are being made by the indirect laser method which is based on the etch process, thus not environment-friendly and not suitable for making a large printing roll. For the pursuit of making a large printing roll for mass printing of electronic devices, we have directly engraved micro-patterns into a Zn plated printing roll using a 30W pulse-modulated fiber laser. We have successfully engraved line patterns ranging from about 15-30${\mu}m$ in width.

• Journal of Auto-vehicle Safety Association
• /
• v.5 no.1
• /
• pp.37-43
• /
• 2013

This paper describes an investigation into coordinated control of electronic stability control (ESC) and active roll control system (ARS). The coordinated control is suggested to improve the vehicle stability and agility features by yaw rate control. The proposed integrated chassis control algorithm consists of a supervisor, control algorithms, and a coordinator. The supervisor monitors the vehicle status and determines desired vehicle motions such as a desired yaw rate and desired roll motion based on control modes to improve vehicle stability. According to the corresponding the desired vehicle dynamics, the control algorithm calculated a desired yaw moment and desired roll moment, respectively. Based on the desired yaw moment and the desired roll moment, the coordinator determines the brake pressures and the ARC motor torques based on control strategies. Closed loop simulations with a driver-vehicle-controller system were conducted to investigate the performance of the proposed control strategy using CarSim vehicle dynamics software and the integrated controller coded using Matlab/Simulink.

• Applied Chemistry for Engineering
• /
• v.33 no.6
• /
• pp.613-617
• /
• 2022

The equipment for fabricating the large-area PTFE nanofiber coated-PTFE foam filter for use as filtration parts of the baghouse that removes particulate matter (PM) in industrial sites was designed and manufactured in this study. The PTFE nanofiber was coated on a commercial PTFE foam filter to increase its PM collection efficiency. The equipment and fabrication processes using a roll-to-roll system were proposed to continuously coat PTFE nanofibers on the surface of the PTFE foam filter. The electrospinning and annealing parts were designed and made by optimizing the equipment for the roll-to-roll system. The surface morphology, composition, and filtration characteristics of the large-area filter fabricated by this equipment were confirmed. PTFE nanofibers were uniformly coated on the large-area filter, and the PTFE nanofiber coated-PTFE foam filter showed PM_2.5 collection efficiency of 91.79% and an appropriate pressure drop of 62 Pa with a face velocity of 1 m/min at 280 ℃.