• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2009년도 추계학술대회 논문집
• /
• pp.289-292
• /
• 2009

The line array roll set process, as one of many kinds of incremental forming processes, is a continuous process in which a flat metal plate is formed into a singly or doubly curved plate through successive passes of forming rolls. It was found that the curvature level of the formed plates in the previous study was well over the curvature required in shipyards. This fact shows that the LARS method has considerable potential for shipbuilding applications. In a shipbuilding yard, hull forming is an important fabrication process in which flat plates are deformed into singly or doubly curved plates. The major purpose of the present study is to estimate experimentally the general applicability of the line array roll set process for the manufacture of ship hull plates. In this study, the target shapes are selected through investigation of the shape classification of ship hull plates that comprise a certain vessel. Forming processes for twisted shapes are analyzed with the finite element method (FEM). Finally, the results of experimental work for two types of target shapes are presented.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1996년도 춘계학술대회 논문집
• /
• pp.541-545
• /
• 1996

In this paper, The performance and functions of automatic flatness control system installed on the 4 hi-reversing mill and has been investigated under actualconditions. A new automatic flatness control system incorporates a measuring roll for measurement and correction calculations, hydraulic roll benders, selective roll cooling, and a programmable controller for interface and data logging. The test results are as following. The more the exit steel strip thickness is thick, the smaller the I value, and the more it is thin, the larger the I value. And, a complex distribution of strip tension was controlled, for example, not only a quarter buckle but also a simple center wave and edge wave. Because the tension deviation is larger at acceleration speed and deceleration speed than steady speed, so automatic flatness control system of contact type is better to adopt over 450 m/min, automatic flatness control system reduces rapidly large flatness deviation. The maximum I value of strip has been decreased to 13 I, and defects caused by poor flatness have been drastically decreased. And coolant temperature for work roll cooling system on the automatic flatness control system is better to adopt about 50-55 .deg. C.

• Environmental Sciences Bulletin of The Korean Environmental Sciences Society
• /
• 제1권2호
• /
• pp.119-124
• /
• 1997

Cloud streets were successfully simulated by numerical model (RAMS) including an isolated mountain near the coast, large sensible heat flux from the sea surface, uniform stratification and wind velocity with low Froude number (0.25) in the inflow boundary. The well developed cloud streets between a pair of convective rolls are simulated at a level of 1 km over the sea. The following five results were obtained: 1) For the formation of the pair of convective rolls, both strong static instability and a topographically induced mechanical disturbance are strongly required at the same time. 2) Strong sensible heat flux from the sea surface is the main energy source of the pair of convective rolls, and the buoyancy caused by condensation in the cloud is negligibly small. 3) The pair of convective rolls is a complex of two sub-rolls. One is the outer roll, which has a large radius, but weak circulation, and the other is the inner roll, which has a small radius, but strong circulation. The outer roll gathers a large amount of moisture by convergence in the lower marine boundary, and the inner roll transfers the convergent moisture to the upper boundary layer by strong upward motion between them. 4) The pair of inner rolls form the line-shaped cloud streets, and keep them narrow along the center-line of the domain. 5) Both by non-hydrostatic and by hydrostatic assumptions, cloud streets can be simulated. In our case, non-hydrostatic processes enhanced somewhat the formation of cloud streets. The horizontal size of the topography does not seem to be restricted to within the small scale where non-hydrostatic effects are important.

• 한국정밀공학회지
• /
• 제28권10호
• /
• pp.1123-1130
• /
• 2011

The pattern shape engraved on the gravure printing roll is one of the most important factors influencing ink transfer. This study focuses on the relations between dot geometry engraved on gravure printing roll and the ink transfer during the gravure printing process. The influence of dot width on printed patterns will be demonstrated. Results reveal that as the width of a dot on the printing roll increases, the ink transfer rate also increases. But over a certain size of width, surface uniformity began to recede. Therefore, proper dot geometry on the printing roll should be decided to guarantee good printing quality according to printing conditions and expected performance of the electronic devices.

• 소성∙가공
• /
• 제19권2호
• /
• pp.120-126
• /
• 2010

The line array roll set(LARS) process, as one of many kinds of incremental forming processes, is a continuous process in which a flat metal plate is formed into a singly or doubly curved plate through successive passes of forming rolls. It was found that the curvature level of the formed plates in the previous study was well over the curvature required in shipyards. This fact shows that the LARS method has good potential for shipbuilding applications. The major purpose of the present study is to estimate experimentally the general applicability of the line array roll set process for the manufacture of ship hull plates. In this study, the target shapes are selected through investigation of the shape classification of ship hull plates that comprise a certain vessel. Forming processes for twisted shapes are analyzed with the finite element method(FEM) and the results of experimental work are presented. On the basis of the experimental and numerical results, the LARS process is applied to the production of real outer hull plates of a small patrol ship.

• 대한조선학회논문집
• /
• 제50권2호
• /
• pp.69-78
• /
• 2013

This study is constructed to investigate the sloshing effect on the motions of a two-dimensional rectangular cylinder experimentally and numerically. The modes of motion under consideration are sway and roll, and also experimental cases are divided by two categories; 1-DoF roll motion and 2-DoF motion (Coupling sway and roll). It is found that the sway response is considerably affected by the motion of the fluid, particularly near the sloshing natural frequency, while the roll response changes comparatively small. The dominant mode of motion is analyzed for 2-DoF experiments as well. The measured data for 1-DoF motions is compared with numerical results obtained by the Multi-modal approach. The numerical schemes vary in detail with the number of dominant sloshing modes; i.e. there is a single dominant mode for the Single-dominant method, while the Model 2 method assumes that the first two modes are superior. For the roll motion, numerical results obtained by the two different methods are relatively in good agreement with the experiments, and these two results are similar in most wave frequency range. However, the discrepancies are apparent where the fluid motion is not governed by a single mode. But both of numerical methods over-predict the motion at the vicinity of the sloshing natural frequency. In order to correct the discrepancy, the modal damping needs to be investigated more precisely. Furthermore, another multi-modal approach, such as the Boussinesq-type method, seems to be required in the region of the intermediate liquid.

• 한국농업기계학회:학술대회논문집
• /
• 한국농업기계학회 2001년도 하계 학술대회 논문집
• /
• pp.73-78
• /
• 2001

• 농업과학연구
• /
• 제49권4호
• /
• pp.771-783
• /
• 2022

In this study, the feasibility of alternative tractor Roll Over Protective Structure (ROPS) designed to evaluate conditions required for testing was confirmed. In accordance with Organization for Economic Cooperation and Development (OECD) code 4, the required load energy of the tractor ROPS was determined. First, the tractor ROPS test was performed and a repeated test was performed using a simplified ROPS as an alternative tractor ROPS. The test procedure is first rearward, second lateral, and last forward based on ROPS. The load test device consists of a load cell that measures force and a LVDT that measures deformation. Precision was confirmed by calculating the relative standard deviation of the simplified ROPS repeated test. Accuracy was analyzed by calculating the mean relative error between the mean measured values in the simplified ROPS test and the tractor ROPS test. As a result, the relative standard deviation was less than 2.5% for force and 3.3% for maximum deformation overall, showed the highest precision in lateral load. The mean relative error value for force measured at the lateral load of simplified ROPS was 0.5%, showing the highest accuracy. In the front load test, the mean relative error of maximum deformation was 20.5%, showing the lowest accuracy. The mean relative error (MRE) was high in the forward load test was because of structural factors of the ROPS. The simplified ROPS model is expected to save money and time spent preparing tractors.

• 대한전자공학회논문지TC
• /
• 제40권12호
• /
• pp.155-160
• /
• 2003

ADC (Analog-to-Digital Converter) 와 DSP (Digital Signal Processor) 의 성능이 향상됨에 따라 아날로그 방식으로 처리하던 IF(Intermidiate Frequency) 대역의 신호를 디지털 방식으로 처리할 수 있게 되었다. 이를 디지털 라디오 또는 디지털 IF라 하고 이는 SDR (software definied radio) 의 초기단계라 할 수 있다. 디지털 라디오 개념을 수신단에 적용할 경우 오버샘플링에 의한 처리 이득을 얻을 수 있으며, 다중 캐리어방식의 수신단 설계가 가능하다. 디지털 수신기에서는 연산량 이득을 위해 데시메이션이 이루어지며, CIC (Cascaded Integrated Comb) 및 halfbandHalfband 필터 등이 앨리어싱방지 필터로 사용된다. 그런데, CIC 필터는 필연적으로 통과대역 내에서 롤 오프 현상이 발생하며, 이것은 수신단 필터의 통과대역 평탄도를 악화시켜서 수신성능의 저하를 초래한다. FIR 필터를 이용하여 보상해 주어야 한다. 본 논문에서는 W-CDMA 디지털 수신기의 수신성능에 최적인 CIC 롤오프 보상 필터를 설계방법을 제시하고, 설계된 필터가 CIC필터의 롤오프 특성을 보상하여 BER(Bit Error Rate)을 최소화시킴을 컴퓨터 시뮬레이션을 통해 확인하였다. 필터 성능을 검증하였다.

• 한국염색가공학회지
• /
• 제29권2호
• /
• pp.86-96
• /
• 2017

To make uniform pressure distributed over the contact surface was necessary to cold pad batch dyeing machine. In this study, to confirm characteristic of flexibility and the contact pressure distribution through experimental analysis of padder roll were controlled by hydraulic cell. When there were no load pressure only inner pressure, the value of displacement in the center of padder were greater than the end of the padder. The results of this study showed that the padder had the optimum value of inner pressure for uniform contact pressure distribution. Measuring the contact pressure in a padder system were driven by using a pre-scale film. Uniform contact pressure distribution of cell padder were a linearly with load pressure and inner pressure. When the load pressure was less than 8 tons, the inner pressure for the uniform contact pressure was 1~4 bar. The padder roll performance curves proposed in this study were available for practical production environments and various roll designs.