• Journal of Power System Engineering
• /
• v.20 no.5
• /
• pp.5-13
• /
• 2016

This study is on wear damage of the material for a molding machine that be used at finally cutting of metal beam made in roll forming process of vehicle bump beam process line. SKD11 steel was used with the material for cutting mold jig. In the cutting mold jig, Ti diffusion heat treatment after vacuum heat treatment was carried out for upgrade of surface hardness and anti-wear. Also, the heat treatments by various methods were performed to compare the wear damage degree against above the existing heat treatment. Wear loss and friction coefficient were obtained from wear test. And, micro Vickers hardness values were compared with damaged parts or not of cutting mold jig. Micro Vickers hardness value appeared higher at the undamaged part by Ti diffusion heat treatment. The micro Vickers hardness well followed a two-parameter Weibull probability distribution.

• The Research Journal of the Costume Culture
• /
• v.25 no.3
• /
• pp.340-358
• /
• 2017

The purpose of this study is to fundamentally examine the vests of the robes "Daeraebok" and "Soraebok" of the Korean Empire from the 1876 Port Opening to the 1910 annexation of Korea to Japan. Among the collections of different robes of the Korean Empire which belong to various universities and institutions, only the vests were surveyed. The shape of the vests in the Korean Empire were single-breasted and double-breasted. Most V-necklines and vests with a shawl collar look like a tailored collar, where the collar outline was shaped like a notched and picked collar, which is a mix of the step collar and roll collar of the 19th century. The rear center line was not flat, but inclined to a triangle. All vests of the robe Daeraebok were equipped with gold buttons, and those of the robe Soraebok had black satin buttons. The tailoring characteristic is that the front has a different material (dark black wool) from the back (black silk). This characteristic is expected to be an important basic piece of information in the restoration and reproduction of the vest, which was worn during the imperial period, especially to reveal its shape, characteristics and composition. This characteristic can also be used as data of cultural contents based on Korean modern history.

• Bulletin of the Society of Naval Architects of Korea
• /
• v.21 no.3
• /
• pp.27-34
• /
• 1984

When a ship is travelling in following seas, the encounter frequency is reduced to be very low. In that case broaching phenomenon is most likely to occur, and it may be due to wave exciting forces acting on ships. It is thought that the wave exciting forces acting on ships in following seas almost consist of two components. One is hydrostatic force due to Froude-Krylov hypothesis, and the other is hydrodynamic lift force due to orbital motion of water particles below the wave surface. In the present paper, the emphasis is laid upon wave exciting sway force, yaw moment and roll moment acting on ships in following seas. The authers take the case that the component of ship speed in the direction of wave propagation is equal to the wave celerity, i.e., the encounter frequency is zero. Hydrostatic force components are calculated by line integral method on Lewis form plane, and hydrodynamic lift components are calculated by lifting surface theory. Furthermore captive model tests are carried out in regular following waves generated by means of a wave making board. Through the comparison between calculated and measured values, it is confirmed that the wave exciting forces acting on ships in following seas can be predicted in terms of present method to a certain extent.

• Journal of the KSME
• /
• v.31 no.4
• /
• pp.389-400
• /
• 1991

압정가공은 열간압정과 냉간압정으로 크게 나눌 수 있으며, 압정기와 피압정재의 종류에 따라 서도 분류한다. 열간압정에서는 알루미늄과 알루미늄합금을 제외하고는 종래에 오직 물만이 냉각겸 윤활제로 사용되어 왔다. 그러나 근년에 와서 열간압정에서도 윤활유를 사용하게 됨으 로서 롤(roll)의 수명연장, 전력소비량의 저감 및 사상(finishing) 강판의 표면품질향상등에 극히 유효하다는 것을 인식하게 되었다. 한편 냉각압정에서는 압정유를 사용해 온 것이 100년 가까이 되는 역사가 있고, 특히 과거 십 수년간에는 상당히 광범위하게 연구가 이루어져서, 많은 실적을 갖게 되었다. 예컨대, 석도원판으로 대표되는 박판압정에 있어서는 고속고압하에서 판의 형상 및 표면정쟁성 향상은 물론이고 저온(에너지 절감, 작업성 개선) 저농도사용(원단위감소)이 이루어 지고, 나아가 장수명(액의 오염이 적은 것)의 압정유가 개발되었다. 또한 마대강 압정에 있어 서는 고윤활이면서도 ECL(electric cleaning line)의 성략도 가능한 압정유 즉 밀크린시트(mill clean sheet) 압정유의 연구도 활발히 진행되고 있다. 압정유의 역할을 살펴보면 열간 또는 냉 간을 불문하고, 롤과 재료간의 감마작용이 주가 되지만 기타 실용적으로는 (1)냉각성 (2)판의 끝맺음(finishing)성 (3)선정선 (4)방장성,비부식성 (5) 내노화성 (6) 오일.스테인(oil stain) (7) 급 유성 (8)액관리성 (9)비수처리성 10) 안전위생 (11)경제성 등을 열거할 수 있다.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.20 no.2
• /
• pp.101-106
• /
• 2021

In this paper, an inspection system has been developed where pneumatic instruments are used to stretch the film using compressed air, thus the curl problem can be overcome. When the pneumatic system is applied, a line scan camera should be used instead of an area camera because the COF surface makes an arc by the air pressure. The distance between the COF and the inspection camera should be kept constant to get a clear image, thus the position of COF is to be monitored on real-time. An operating software has been also developed which is switching on/off the pneumatic system, determining the COF position using a camera vision, displaying the contour of the COF side view, sending self-diagnosis result and etc. The developed system has been examined using the actual roll of COF, which convince that the system can be an effective device to inspect the COF rolls in process.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.29 no.2
• /
• pp.248-253
• /
• 2023

Most offshore platforms utilize chain mooring systems for position keeping. However, information regarding related design modification processes is scarce in literature. This study focuses on the floating liquefied natural gas (LNG) bunkering terminal (FLBT) as the target of shore platform and analyzes the corresponding initial mooring design and model tests via numerical simulations. Subsequently, based on the modified design conditions, a new mooring system design is proposed. Adjusting the main direction of the mooring line bundle according to the dominant environmental direction is found to significantly reduce the mooring design load. Even turret-moored offshore platforms are exposed to beam sea conditions, leading to high mooring tension due to motions in beam sea conditions. Collinear environmental conditions cannot be considered as design conditions. Mooring design loads occur under complex conditions of wind, waves, and currents in different environmental directions. Therefore, it is essential appropriately assign the roll damping coefficients during mooring analysis because the roll has a significant effect on mooring tension.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.19 no.2
• /
• pp.200-206
• /
• 2013

The paper was investigated on the mooring forces(or tension) and motion response characteristics for a 8-point mooring floating dock in regular waves using a commercial code(AQWA). To achieve the aim of the research, a numerical simulation was adapted on an inner port environment condition, which the water depth is 10 meters, significant wave amplitude(1.05 m). wave period(3.85 sec), wind speed(20.21 m/s), wind and current direction ($90^{\circ}$), incident waves(${\chi}=180^{\circ}$, $135^{\circ}$ and $90^{\circ}$). The dimension of the numerical model is length(140 m), breadth(32 m), depth(14.6 m). The maximum length of a mooring line is 120m. We can expected that roll and pitch motions appeared in beam seas better than head sea. the mooring forces also indicated higher in bean seas than in head seas including wind forces.

• Journal of the Korean Society for Marine Environment & Energy
• /
• v.20 no.2
• /
• pp.91-99
• /
• 2017

The parametric study was performed for performance enhancement of wave energy converter(WEC) using a submerged pendulum plate. The wave exciting moment and hydrodynamic moment were obtained by means of eigenfunction expansion method based on the linear potential theory, and then the roll response of a pendulum plate and time averaged extracted power were investigated. The optimal PTO damping coefficient was suggested to give optimal extracted power. The peak value of optimal extracted power occurs at the resonant frequency. The resonant peak and it's width increase, as the height and thickness of a pendulum plate increase. The mooring line installed at the end of the pendulum plate is effective for extracting wave energy because it can not only induce the resonance with the waves of the installation site but also increase the restoring moment in case of PTO-on. The WEC using a rolling pendulum plate suitable for the shallow water acts as breakwater as well as energy extraction device.

• Korean Journal of Applied Biomechanics
• /
• v.21 no.2
• /
• pp.223-230
• /
• 2011

The purpose of this study was to analysis the effect of form and hardness of outsoles on the motion of the lower extremity joints and on foot pressure during gait. The subjects were 15 women(mean age, $48.5{\pm}2.4$ years), who had no serious musculoskeletal, coordination, balance or joint/ligament problems within 1 year prior to the study. The pelvic tilt, joint angles at the lower extremities and the vertical ground reaction force(GRF) were compared during gait with 3 types of shoes (A, B, C) by using one-way repeated ANOVA(p<.05). During gait, the peak tilt angle and the range of motion(ROM) of the ankle and knee joints were found to be significantly different among the 3 types of shoes. The type C shoes showed a significantly lower mean second maximum vertical GRF than types A and B. The curved outsoles of type C shoes, which had a form and hardness different from those of A and B, was designed strategically for walking shoes to provide stability to the Additionally, type C induced the dispersion of eccentric pressure and made the center of pressure roll over to the center line of the foot.

• 한국신재생에너지학회:학술대회논문집
• /
• 2011.05a
• /
• pp.116.1-116.1
• /
• 2011

Materials with a combination of high electrical conductivity and optical transparency are important components of many electronic and optoelectronic devices such as liquid crystal displays, solar cells, and light emitting diodes. In this study, to fabricate a low-resistance and high optical transparent electrode film for organic photovoltaic, the following steps were performed: the design and manufacture of an electroforming stamp mold, the fabrication of thermal roll imprinted (TRI) poly-carbonate (PC) patterned films, the manufacture of high-conductivity and low-resistance Ag paste which was filled into patterned PC film using a doctor blade process and then coated with a thin film layer of conductive polymer by a spin coating process. As a result of these imprinting processes the PC films obtained a line width of $10{\pm}0.5{\mu}m$, a channel length of $500{\pm}2{\mu}m$, and a pattern depth of $7.34{\pm}0.5{\mu}m$. After the Ag paste was used to fill part of the patterned film with conductive polymer coating, the following parameters were obtained: a sheet resistance of $9.65{\Omega}$/sq, optical transparency values were 83.69 % at a wavelength of 550 nm.