• 한국자동차공학회논문집
• /
• 제8권6호
• /
• pp.267-278
• /
• 2000

Vehicle dynamic models in handing and stability analysis are divided into three groups: bicycle model, roll axis model and full vehicle model. Bicycle model is a simple linear model, which hag two wheels with load transfer being ignored. Roll axis model treats left and right wheels independently. In this model, load transfer has a great effect on nonlinearity of tire model. Effects of suspension system can be analyzed by using full vehicle model, which is included suspension stroke motions. In this paper, these models are validated and compared through comparison with road test, and the effects of suspension kinematics and compliance characteristics on vehicle motion are analyzed. In handling and stability analysis, roll axis model can simulate the real vehicle motion more accurately than full vehicle model. Compliance steer has a significant effect, but the effect of suspension kinematics is negligible.

• Journal of Welding and Joining
• /
• 제27권3호
• /
• pp.85-91
• /
• 2009

A roll projection welding machine is introduced to fabricate metallic sandwich plate consisting of a structured inner sheet with projection-like shape and a pair of skin sheets. To fabricate the metallic sandwich plate of consistent and good quality, two process monitoring methods are introduced; dynamic resistance monitoring and skin sheet temperature monitoring. Dynamic resistance monitoring has no time delay but gives only averaged value over plate width. Skin sheet temperature monitoring has certain amount of time delay but is good for predicting weld quality of specified position. By the two complementary monitoring methods, the characteristics of the new welding process is successfully understood.

• Journal of Positioning, Navigation, and Timing
• /
• 제6권4호
• /
• pp.135-140
• /
• 2017

This paper proposes a signal merging algorithm to increase the signal-to-noise ratio (SNR) of a GPS correlator output to estimate the roll angle of a rotating vehicle in a weak GPS signal environment. Rotation Locked Loop (RLL) algorithm is used to estimate a roll angle using the characteristics that the power of the GPS signal measured at the receiver of a rotating vehicle varies periodically. First, delay times are calculated to synchronize GPS signals using satellites' and receiver's positions and the rotation frequency of a vehicle, and then correlator outputs are delayed in time and merged with each other, resulting in the increase of an SNR in a correlator output. Finally, simulations are conducted and the performance of the proposed algorithm is validated.

• 대한기계학회논문집
• /
• 제18권4호
• /
• pp.946-957
• /
• 1994

In the steel industries, direct rolling process for production of strip from molten metal has been investigated to simplify processes, to minimize energy consumption, and to improve quality of the strip. In this study, two kinds of practicable scale cooling rollers are proposed. And heat transfer analysis of pool region and cooling roller considering flow of molten metal and roll rotation respectively using the finite element method are performed to obtain the proper initial condition and to observe cooling characteristics of cooling roller. From the results, variations of solidification final points and temperature distribution in roller are observed quantitatively according to roll rotation.

• International Journal of Automotive Technology
• /
• 제3권3호
• /
• pp.123-128
• /
• 2002

This paper presents the design of an active roll control system for a ground vehicle and an experimental study using an devised electric-actuating roll control system. Based on a three degree of freedom linear vehicle model, the controller is designed using lateral acceleration and rollrate feedback. In order to investigate the feasibility of an active control system, experimental work is carried out using a hardware-in-the-loop (Hil) setup which has been constructed by the devised electric-actuating system and the full vehicle model including tire characteristics. The performance is evaluated by an experiment using the Hil setup with limited bandwidth. Finally, in order to enhance the control performance in the transient region, a hybrid control strategy is proposed and evaluated.

• 한국자동차공학회논문집
• /
• 제12권5호
• /
• pp.146-153
• /
• 2004

Torsion beam rear suspension has been widely adopted to the rear suspension of vehicle by reason of simple structure and cost competitiveness. Since the kinematic characteristics of torsion beam rear suspension are determined by elastic behavior of torsion beam, quasi-static analysis based on finite element modeling of torsion beam has been conducted to obtain the kinematic parameters of torsion beam rear suspension. In this paper, simple kinematic equations with rear geometric parameters are derived to predict the kinematic behavior of torsion beam rear suspension. The suspension design parameters such as roll center height, roll stiffness, roll steer and roll camber can be easily obtained with the kinematic equations. The suggested kinematic equations are validated from comparison with the test results and solution offered by ADAMS. The suspension design parameters varied with the position of torsion beam are discussed.

• International Journal of Automotive Technology
• /
• 제7권6호
• /
• pp.703-714
• /
• 2006

The growing concern surrounding rollover incidences and consequences of Sports Utility Vehicles(SUV) have prompted to investigate the sensitivity of critical vehicle parameters on rollover. In this paper, dynamic rollover simulation of Sports Utility Vehicles is carried out using a validated nonlinear vehicle model in Matlab/Simulink. A standard model is considered and critical vehicle parameters like CG height, track width and wheel base are varied within chosen specified limits to study its influence on roll behavior during a Fishhook steering maneuver. A roll stability criterion based on Two Wheel Lift Off(TWLO) phenomenon is adopted for rollover propensity prediction. Further dynamic rollover characteristics of the vehicle are correlated with Static Stability Factor(SSF), Roll Stability Factor(RSF) and Two Wheel Lift Off Velocity(TWLV). These findings will be of immense help to SUV chassis designers to determine safety limits of critical vehicle parameters and minimize rollover incidences.

• 소성∙가공
• /
• 제28권4호
• /
• pp.197-202
• /
• 2019

This paper proposes a precise mathematical model for the prediction of the variation of the roll force across a strip in cold rolling. It further describes the deformation characteristics of the strip using a 3-D finite element method. The different features of hot rolling and cold rolling through a 3-D finite element method are shown. The predicted roll force profile and tension profile are verified through comparison with the prediction from a 3-D finite element method.

• 한국결정성장학회지
• /
• 제33권5호
• /
• pp.191-195
• /
• 2023

핸드폰 Backcover에 적용한 3층 나노코팅 필름을 롤투롤(roll-to-roll) 연속 공정을 통하여 제조하였다. 세라믹/금속/세라믹 3층 구조의 코팅층을 도입함으로써 금속 고유의 반사 특성을 유지하면서 전기적으로는 절연 특성을 유지하였다. 길이와 폭이 각각 1500 nm, 500 nm인 대면적 PET 필름 위에 도입된 복합 코팅층의 두께는 60 nm 이하를 보였고 모든 영역에서 균일한 두께를 유지하고 있음을 확인하였다. 나노코팅 필름의 파장대(240~1600 nm)에 따른 투과율은 파장이 증가함에 따라 투과율 역시 점차 증가하고 있으며, 적외선 영역인 1,000 nm에서 약 48 %, 가시광선 영역에 해당하는 550 nm에서는 약 35.5 %의 투과율을 보였다. 이는 코팅된 Backcover의 요구 수준(< 40 %)에 부합한다.

• 대한조선학회논문집
• /
• 제37권2호
• /
• pp.30-37
• /
• 2000

3톤급 소형어선의 나선, 빌지킬 및 중앙날개(central wing)가 부착된 상태의 3가지 모델에 대해 파랑중(선수파)에서 속도 변화, 초기각의 변화 및 OG(무게중심과 횡동요 중심간의 거리)의 변화에 따른 횡동요 감쇠시험에 의해 감쇠 특성을 비교하였다. 파주기 변화에 대한 영향도 포함시켰다. 또한 에너지법에 의해 선형 및 비선형 속도항에 의존하는 횡동요 감쇠모멘트를 계산하여 시험값과 비교하였으며 3가지 모델에 대한 에너지 발산 형태도 비교하였다. 파랑이 있을 때 감쇠력은 전진속도가 없는 경우는 증가하였으나 전진속도가 있는 경우는 부가물이 부착된 경우에는 양력증가에 의한 감쇠력 증가 기여도가 아주 크기 때문에 파랑에 의한 감쇠력 증가는 미소하였다.