• Transactions of the Korean Society of Mechanical Engineers
• /
• v.19 no.1
• /
• pp.99-110
• /
• 1995

An industrial robot needs a simple and robust control algorithm obtaining high precision control performance in spite of disturbance and parameter's change. In this paper, for solving this problem, a new sliding mode control algorithm is proposed and applied to the trajectory control of a SCARA type robot. The proposed algorithm has diminished the chattering occurring in sliding mode by setting a dead band along the switching line on the phase plane. It shows that we can easily obtain a simple switching control input satisfying sliding mode in spite of regarding nonlinear terms of a manipulator and servo system as disturbance. A guideline for selection of dead-band width is determined by optimal value of cost function presenting magnitudes of chattering and error. By this algorithm, we can expect the high performance of the trajectory tracking of an industrial robot which needs a robust and simple algorithm.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.55 no.2
• /
• pp.83-88
• /
• 2006

This paper proposes a method that minimizes the consumed energy by searching the optimal locations of the mass centers of the biped robot's links using Genetic Algorithm. This paper presents a learning controller for repetitive gait control of the biped robot. The learning control scheme consists of a feedforward learning nile and linear feedback control input for stabilization of learning system. The feasibility of learning control to the biped robotic motion is shown via computer simulation and experimental results with 24 DOF biped walking robot.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.16 no.2
• /
• pp.162-172
• /
• 2011

This paper proposes embedded System of two wheeled inverted pendulum robot designed by model based design method, using MATLAB/SIMULINK and LEGO NXT Mindstorms. At first, stability and performance of controller is verified through modeling and simulation. After that direct conversion from simulation model to C code is carried and effectiveness of controller is experimentally verified. Two wheeled inverted pendulum robot has basic function about autonomous balancing control using principle of inverted pedulum and it is also possible to arrive at destination. In this paper, state feedback controller designed by quadratic optimal control method is used. And quadratic optimal control uses state feedback control gain K to minimize performance index function J. Because it is easy to find gain, this control method can be used in the controller of two wheeled inverted pendulum robot. This proposed robot system is experimentally verified with following performances - balancing control, disturbance rejection, remote control, line following and obstacle avoidance.

• 제어로봇시스템학회:학술대회논문집
• /
• 1997.10a
• /
• pp.1840-1843
• /
• 1997

The task environment of a robot is changing rapidly and task itself becomes complicated due to current industrial trends of multi-product and small lot size production. A convenient user-interfaced off-line programming(OLP) system is being developed in order to overcome the difficulty in teaching a robot task. Using the OLP system, operators can easily teach robot tasks off-line and verify feasibility of the task through simulation of a robot prior to the on-line execution. However, some task errors are inevitable by kinematic differences between the robot model in OLP and the actual robot. Three calibration methods using image information are proposed to compensate the kinematic differences. These methods compose of a relative position vector method, three point compensation method, and base line compensation method. To compensate a kinematic differences the vision system with one monochrome camera is used in the calibration experiment.

• 제어로봇시스템학회:학술대회논문집
• /
• 2003.10a
• /
• pp.813-817
• /
• 2003

By increasing trades between countries, importance of harbors is becoming serious, including our country. When it comes to Container Crane Operation, the most important matter is how many containers are loaded in a truck or a ship by given time. This can be a crucial matter of harbors in taking care of materials. The present harbors' crane uses a wire-rope conveyance materials are transported in the air and have high free-angle of location. The sway can cause the delay of time, wrong position of Trolley and the damage of materials. In this study, we obtain the optimal PID parameters with GA(Genetic Algorithm) and apply those parameters to the PID Controller. In the result of the experimentation, we can see how effectively the PID controller, applied with the optimal parameters obtained by GA, can control the sway angle.

• Journal of the Korean Institute of Telematics and Electronics B
• /
• v.31B no.1
• /
• pp.41-48
• /
• 1994

The conventional resolved motion control is not applicable for the control of robots on the spacecraft on account of the floating base of the robots. When the robots perform the assembly or repair operations, the position and attitude of the base satellite are disturbed by the reaction force/moment caused by the robot motion. This reaction will cause error on the robot. motion. Therefore, we define a new type of Jacobian(Extended Jacobian) to minimize the effects of reaction on the accuracy of the robot performing assembly or repair operations. In this paper, we utilize the redundancy of the closed chain system to minimize the effects of the robot motion on the position and attitude of spacecraft. This will results in the accurate assembly and repair operations by the robot.

• Journal of the Korean Society for Precision Engineering
• /
• v.25 no.2
• /
• pp.65-71
• /
• 2008

In this paper, we propose a new driving mode control algorithm for a mobile robot based on obstacle detection. The robot has a variable geometry single-tracked mechanism, so it can maximize a contact length with ground for the adaptability to off-road and puesue a stable system due to the lower center of gravity. However this robot system embodied passive type according to operator. In this reason, several problems are detected. So, this research presents a new method of obstacle detection using PSD infrared sensors and translates the variable tracks on the best suited driving mode actively. And experimental results about mentioned are presented.

• 제어로봇시스템학회:학술대회논문집
• /
• 1992.10a
• /
• pp.387-392
• /
• 1992

This paper presents a local trajectory generation method which is based on a sequence of reference posture-velocities and the efficient low level control algorithm which constructs the complete smooth curve from the trajectory specification. The reference trajectory generator(RTG) which is in between the local path planner(LPP) and the robot motion controller(RMC) generates a sequence of set-points for each path segments from the LPP and pass it to the RMC. The RMC controls the motions of vehicle which should follow the sequence. In the feedback controller of VMC, the method which compensates robot posture-velocity error correctly is used. These methods are implemented on indoor autonomous vehicle, 'ALIVE' mobile robot. The ALIVE mobile robot system is implemented on the 32bit VME bus system: the two VME CPU's are used for RTG and RMC, while the 80C196KC-based VME board is used for motor controller.

• Journal of the Korean Society for Precision Engineering
• /
• v.15 no.11
• /
• pp.100-107
• /
• 1998

This paper presents the development of estimation model and control method based on the new robot vision. This proposed control method is accomplished using the sequential estimation scheme that permits placement of the rigid body in each of the two-dimensional image planes of monitoring cameras. Estimation model with six parameters is developed based on the model that generalizes known 4-axis scara robot kinematics to accommodate unknown relative camera position and orientation, etc. Based on the estimated parameters, depending on each camera the joint angle of robot is estimated by the iteration method. The method is experimentally tested in two ways, the estimation model test and a three-dimensional rigid body placement task. Three results show that control scheme used is precise and robust. This feature can open the door to a range of application of multi-axis robot such as assembly and welding.

• Journal of Institute of Control, Robotics and Systems
• /
• v.21 no.6
• /
• pp.497-502
• /
• 2015

One of the goals in the field of mobile robotics is the development of personal service robots for the elderly which behave in populated environments. In this paper, we describe a security robot system and ongoing research results that minimize the risk of the elderly and the infirm to access an area to enter restricted areas with high potential for falls, such as stairs, steps, and wet floors. The proposed robot system surveys a potential falling area with an equipped laser scanner sensor. When it detects walking in elderly or infirm patients who in restricted areas, the robot calculates the velocity vector, plans its own path to forestall the patient in order to prevent them from heading to the restricted area and starts to move along the estimated trajectory. The walking human is assumed to be a point-object and projected onto a scanning plane to form a geometrical constraint equation that provides position data of the human based on the kinematics of the mobile robot. While moving, the robot continues these processes in order to adapt to the changing situation. After arriving at an opposite position to the human's walking direction, the robot advises them to change course. The simulation and experimental results of estimating and tracking of the human in the wrong direction with the mobile robot are presented.