• Journal of Korean Society of Transportation
• /
• v.6 no.1
• /
• pp.43-53
• /
• 1988

This study is to find the proper method of estimating urban road traffic capacity. To estimate road traffic capacity, the following methods are chosen ; 1) crossing point of Q-V and S-V, 2) critical velocity and density of Q-V-K model, 3) V-K model with density parameter. The density estimated through S-V relation is 174 veh./km. The methods used in this paper yields more stable values with 2286 veh./h/ in average. The estimated average capacity by three methods are 2272 veh./h. in multilane road. 2411 veh./h in three lane road and 2185 veh./h. in two lane road.

• Journal of the Korean Geosynthetics Society
• /
• v.11 no.3
• /
• pp.11-17
• /
• 2012

This paper presents the results of investigation into bearing capacity of a geocell reinforced load base. In order to analyze variation of bearing capacity of the geocell reinforced road base comparing to without reinforced geocell road base, a series of full-scale tests were performed and measured using FWD (Falling Weight Deflectometer). The results indicate that bearing capacity of geocell (T=1.5 mm) reinforecd road base increase than the unreinforced road base.

• KIPS Transactions on Computer and Communication Systems
• /
• v.5 no.10
• /
• pp.327-330
• /
• 2016

In the road environment with lots of vehicles, we can increase the number of vehicles on the road (i.e., road capacity) and enhance the comfortability of drivers if vehicles are organized into platoons. In the traditional vehicle platooning mechanisms, a pre-determined set of vehicles are allowed to form a platoon and, among them, a specific vehicle is designated as the platoon leader. In this type of platoon mechanisms, platoon is limited in improving the road capacity because the vehicles allowed to involve into platooning are restricted. Therefore, in this paper, we propose an adaptive platoon formation mechanism that allows any vehicle to be a platoon leader from which a platoon is formed. In the proposed mechanism, a platoon leader is elected based on the relative velocity and location information of neighboring vehicles obtained through the periodic exchange of beacon messages among vehicles. Through the NS-3 based simulations, we show the performance of our proposed mechanism in terms of road capacity improvement.

• Korean System Dynamics Review
• /
• v.12 no.1
• /
• pp.75-87
• /
• 2011

Congestion problems can be approached from the viewpoint of system dynamics theory. The relationship between road capacity and congestion can be explained by the 'relative control' archetype among four system archetypes suggested by Wolstenholme. There is a balancing feedback loop between road capacity and road congestion. However, there is another balancing loop between road congestion and car traffic volume, which keeps disrupting the equilibrium of the former loop. A system dynamics model, which is based on a partial adjustment model of induced traffic in the literature, is built to simulate three road building scenarios: 'Expanding investment', 'Balancing investment' and 'Frozen road investment' scenarios. The 'Expanding investment' scenario manages to drop congestion levels by 9% over 30 years, however, causing much higher emissions of $CO_2$ than other scenarios. The trade-off relationship between congestion levels and environmental costs must be taken into consideration for road investment policies.

• Environmental Engineering Research
• /
• v.25 no.3
• /
• pp.366-373
• /
• 2020

The autonomous vehicles (AVs) could make a positive or negative impact on reducing mobile emissions. This study investigated the changes of mobile emissions that could be caused by large-scale adoption of AVs. The factors of road capacity increase and speed limit increase impacts were simulated using a conceptual modeling approach that combines a hypothetical speed-emission function and a traffic demand model using a virtual transportation network. The simulation results show that road capacity increase impact is significant in decreasing mobile emissions until the market share of AVs is less than 80%. If the road capacity increases by 100%, the mobile emissions will decrease by about 30%. On the other hand, driving speed limit increase impact is significant in increasing mobile emissions, and the environmentally desirable speed limit was found at around 95 km/h. If the speed limit increases to 140 km/h, the mobile emissions will increase by about 25%. This is because some vehicles begin to bypass the congested routes at high speeds as speed limit increases. Based on the simulation results, it is clear that the vehicle platooning technology implemented at reasonable speed limit is one of the AV technologies that are encouraging from the environmental point of view.

• Journal of Korean Society of Forest Science
• /
• v.107 no.3
• /
• pp.287-293
• /
• 2018

This study was carried out to provide surface bearing capacity reinforcement of forest road by sub-base facilities based on a soft ground use of geosynthetics to prevent the damage of the road surface passing heavy logging trucks and to pass smoothly heavy truck against growing timber harvesting. The analysis of the road surface bearing capacity as progressing time and the increase of the number of passage of heavy logging trucks were conducted experimental section of forest road on the soft ground in the Forest Technology and Management Research Center. As a result, it was found that the road surface bearing capacity were stabilized at CBR of 15% or more, the effect of reinforcement by type of geosynthetics showed no significant difference after the lapse of about 1 year. After reaching the passage of 300 times for the heavy logging trucks on the sub-base construction section, the settlements was stabilized below the allowable standard of 50 mm, road surface bearing capacity also improved to more than CBR 20% and there was no significant difference in the thickness of the sub-base. However, in the section where the sub-base is not constructed, it is found that the lack of surface bearing capacity with the settlements more than the allowable standard is not possible to pass the heavy logging trucks. Therefore, in order to reinforce the road surface bearing capacity of the soft ground for the passage of the heavy logging trucks, it is necessary to construct a sub-base of at least 0.2 m when using geosynthetics.

• International Journal of Highway Engineering
• /
• v.17 no.2
• /
• pp.123-134
• /
• 2015

PURPOSES : The key point of a multimodal LOS (level-of-service) evaluation system is that all of the modes are mutually associated to determine each mode's LOS. For example, the LOS of the bicycle mode is measured based on not only bicycle volumes, but also automobile volumes. However, the Korea Highway Capacity Manual (KHCM) still focuses on the automobile mode in evaluating the LOS of the roads. Additionally, the KHCM's LOS of the other modes, except for the automobile, is not consistent with actual road conditions. The KHCM, therefore, needs to develop and introduce a multimodal LOS system in order to evaluate the service conditions more accurately. METHODS: As a preliminary step to the introduction of multimodal LOS research, in this study the current problem of the KHCM's LOS system through a close review and comparison with other HCMs (highway capacity manuals) was identified. Secondly, a field survey and investigation of the urban streets to apply the HCM's multimodal LOS system was conducted. Finally, a comparison analysis of the results of the HCM and KHCM LOS was performed. RESULTS: In the study, it was found that the results of the LOS for the automobile mode did not show a significant difference between the HCM and KHCM. However, the LOS of the bicycle and pedestrian mode tended to be worse in the multimodal LOS system, which results from considering the effects of the automobile mode. Moreover, it was found that many cases have the potential to improve the overall LOS conditions, while reducing the automobile capacity. CONCLUSIONS: With the introduction of the multimodal LOS system, road diet and complete streets can be easily applied to ans actual road improvement project. Ultimately, the multimodal LOS system should be introduced into the KHCM, which can then be applied to traffic impact studies and other road improvement projects for more accurate evaluations.

• Journal of the Korean GEO-environmental Society
• /
• v.24 no.12
• /
• pp.19-29
• /
• 2023

The main problem with roads is that cracks and settlement occur over time due to loads acting from the surface layer. One way to solve this problem is to use Geocell. Geocell can be used for structural reinforcement for erosion prevention, ground stabilization on flat and steep slopes, load bearing, and ground preservation. In this study, analyzed road pavement application cases using Geocell and purpose of this study is to analyze the bearing capacity of a road paving method including Geocell using field tests and LFWD(Light Falling Weight Deflectometer) equipment. In addition, the bearing capacity was compared and analyzed with the existing traditional road pavement method.

• Journal of the Korean Geotechnical Society
• /
• v.28 no.3
• /
• pp.5-14
• /
• 2012

In the current design codes for anti-freezing layer, the thickness of anti-freezing layer is calculated by freezing depth against the temperature condition. Therefore, they have a tendency of over-design and uniform thickness without the considerations of thermal stability, bearing capacity and frost susceptibility of materials. So, it is essential for studying the appropriateness and bearing capacity of road foundation materials as well as their seasonal and mechanical properties to take an appropriate and reasonable design of the road structure system. In this paper, the freezing and bearing capacity characteristics of typical road foundation materials were evaluated in the large scale laboratory test. LFWD (light falling weight deflectometer) was used to determine the change of elastic modulus ($E_{LFWD}$) caused by to the frost heave and thaw. Furthermore, the influence of crushed natural aggregate on the freezing of the subgrade soil was studied to verify the function and effectiveness of the anti-freezing layer.

• International Journal of Highway Engineering
• /
• v.16 no.1
• /
• pp.57-62
• /
• 2014

PURPOSES : Capacity is a main factor of determining the number of lane in highway design or the level of service in road on operation. Previous studies showed that breakdown may occur before capacity is reached, and then it was concluded that capacity is a stochastic value rather than a deterministic one. In general, estimating capacity is based on average over maximum traffic volume observed for capacity state. This method includes the empirical distribution method(EDM) and would underestimate capacity. This study estimated existing empirical methods of estimating stochastic highway capacity. Among the studied methods are the product limit method(PLM) and the selected method(SM). METHODS : Speed and volume data were collected at three freeway bottleneck sites in Cheonan-Nonsan and West Sea Freeway. The data were grouped into a free-flow state or capacity state with speeds observed in the bottlenecks and the upstream. The data were applied to the empirical methods. RESULTS : The results show that the PLM and SM estimated capacity higher than EDM. The reason is that while the EDM is based on capacity observations only, the PLM and SM are based on free-flow high volumes and capacity observations. CONCLUSIONS : The PLM and SM using both free-flow and capacity observations would be improved to enhance the reliability of the capacity estimation.